1. Introduction
The KC23C01 is a versatile 1-channel multifunction delay relay module designed for various timing and counting applications. It supports DC 5V, 12V, or 24V power inputs and offers adjustable delay times and pulse counting capabilities. This manual provides essential information for setting up, operating, and troubleshooting your module.
2. Features
- Wide range of applications for timing and counting tasks.
- User-friendly interface for easy operation.
- Stable and reliable performance.
- Available in three voltage specifications: 5V, 12V, and 24V.
- Adjustable pulse count value from 0 to 9999.
- Delay time adjustable from 0.1 seconds to 9,999,999.9 seconds (approximately 115.7 days).
- Supports 12 working modes (F00-F05 for single-shot pulse control, F10-F15 for pulse counting control).
- 8 working modes allow setting the number of cycles.

Figure 2.1: KC23C01 Multifunction Relay Module Overview with key features highlighted.
3. Specifications
| Parameter | Value |
|---|---|
| Working Voltage | DC 5V / DC 12V / DC 24V (optional) |
| Relay Load | 10A/250VAC; 10A/30VDC |
| Working Current (Digital Tube OFF) | Relay OFF: 6mA, Relay ON: 35mA |
| Working Current (Digital Tube ON) | Relay OFF: 29mA, Relay ON: 56mA |
| Operating States | Working, Power Saving, Setting |
| Input Port | Optocoupler isolation, compatible with NPN/PNP input (5-24V switch signal) |
| Output Port | 10A Relay (NO, COM, NC terminals) |
| Working Modes | F00-F05 (Single-shot pulse control/General delay relay), F10-F15 (Pulse counting control) |
| Delay Time Range | 0.1s - 9,999,999.9s (115.7 Days) |
| Delay Time Step/Precision | 0.1s / 0.01s |
| Pulse Count Value | 0 - 9999 (settable) |
| Dimensions (L*W*H) | 74.4mm * 40.5mm * 19.6mm |
| Weight | 29g |
4. Setup and Wiring
4.1 Component Identification
Familiarize yourself with the components and terminals on the module:

Figure 4.1: Key components and terminals of the KC23C01 module. Includes Power Supply (VCC, GND), 4-bit digital tube, NPN/PNP switch/digital signal input port (IN+, IN-), and control buttons (Set, ++, --, OK).
4.2 Wiring Methods for Trigger Signal Input
There are three primary methods for connecting the trigger signal to the input terminal:
- No External Signal Source Required: The module can be triggered directly, often using an onboard or simple external button connected to the input terminals.
- Trigger with NPN Source: For low-level trigger signals from NPN type sensors or switches.
- Trigger with PNP Source: For high-level trigger signals from PNP type sensors or switches.

Figure 4.2: Wiring diagrams for the KC23C01 module, showing connections for power, load, and the three trigger input methods.
Important: Ensure correct polarity when connecting the power supply (VCC and GND) and the load to the relay terminals (NO, COM, NC). The relay can switch DC 1-110V or AC 85-265V loads.
5. Operating Instructions
5.1 Button Functions
- Short press: Key press duration less than 2 seconds.
- Long press: Key press duration more than 2 seconds.
5.2 Module States
The module operates in three main states: Working, Power Saving, and Setting. A Query state is also available.
- Working State: This is the default power-on state.
- In F00-F05 modes, the digital tube displays the remaining time.
- In F10-F15 modes, it displays both the remaining time and the pulse count value.
- If the remaining time is greater than four digits, a short press of the 'OK' key will scroll and display the full remaining time once.
- Setting State: Used to configure parameters.
- Short press the 'SET' key to enter the setting state.
- Short press 'SET' again to cycle through parameters.
- Use '++' and '--' keys to modify the selected parameter value.
- Short press the 'OK' key to save the parameters and exit the setting state.
- Note: After setting parameters, the module must be powered off and on again for changes to take effect.
- Query State: Allows viewing current parameters without modifying them.
- Without entering the parameter setting state, short press the 'SET' button to enter the query state.
- Press 'SET' to switch between parameters.
- Short press the 'OK' button to exit the query state.
- Power-Saving State: The digital tube display is off to conserve power, but other functions continue to operate normally.
- To enter: Long press the 'OK' button for 5 seconds.
- To exit: Long press the 'OK' button for 5 seconds.
- Even in power-saving state, you can still enter the setting and query states. The module will automatically return to power-saving state after 20 seconds of no key operation.
- After powering on, the digital tube displays for 20 seconds before potentially entering power-saving mode if configured.
5.3 Factory Settings
To restore the module to its default factory settings:
- Press and hold the '++' and '--' keys simultaneously for 3 seconds.
- This action will restore factory settings and turn off the digital tube display.
- Note: The module will run with default parameters after a reboot following a factory reset.
6. User Tips
- Understanding Programming Modes: The module offers F00-F15 working modes. For detailed programming instructions specific to each mode (e.g., how to set delay types, cycle counts, or pulse triggers for F01, F02, F10, etc.), it is recommended to consult the comprehensive programming guide or specific mode documentation provided by the manufacturer, as these details can be extensive.
- Power Cycle After Settings: Always remember to power cycle the module (turn it off and then on again) after making any changes in the setting state to ensure the new parameters are properly loaded and active.
7. Troubleshooting
- Inexplicable Problems: If the module behaves unexpectedly or encounters issues, first try powering it off and then on again. Many issues can be resolved by a simple reboot, especially if parameters were recently changed without a power cycle.
- Persistent Problems: If issues persist after a power cycle, perform a factory reset by pressing and holding the '++' and '--' keys simultaneously for 3 seconds. After the reset, power cycle the module again. This will revert all settings to their defaults, which can help identify if the problem is configuration-related.
- No Display/Module Unresponsive: Check the power supply connections and ensure the correct voltage (5V, 12V, or 24V) is being supplied. Verify that the module is not in a power-saving state (long press 'OK' for 5 seconds to exit).
8. Maintenance
- Keep the module clean and free from dust and debris.
- Avoid exposing the module to moisture, extreme temperatures, or corrosive environments.
- Ensure proper ventilation if the module is enclosed, especially when switching high loads, to prevent overheating.
- Do not attempt to disassemble the module beyond what is necessary for wiring, as this may void any potential warranty and could damage internal components.
9. Warranty and Support
For warranty information, technical support, or further assistance, please contact the seller or manufacturer directly. Keep your purchase records handy when seeking support.