1. Introduction
Thank you for choosing the Hirisi Wireless Fishing Bite Alarm Set B1235. This advanced system is designed to enhance your fishing experience by providing reliable bite indication for carp and coarse fishing. The set includes wireless bite alarms and a receiver, offering adjustable settings for volume, tone, and sensitivity, along with a waterproof design and a long operating range. Please read this manual carefully to ensure proper setup and operation of your new fishing alarm set.

2. Package Contents
Your Hirisi Wireless Fishing Bite Alarm Set B1235 comes in two configurations:
- 1 plus 2 set: Includes 1 Receiver + 2 Bite Alarms
- 1 plus 3 set: Includes 1 Receiver + 3 Bite Alarms
Please verify that all components are present and in good condition upon unboxing.


3. Product Overview
The Hirisi B1235 system consists of individual bite alarms and a central receiver. Each component is designed for ease of use and durability in fishing environments.
3.1. Component Identification

| No. | Component (Bite Alarm) | No. | Component (Receiver) |
|---|---|---|---|
| 1 | Warning LED-light (Left) | 8 | Volume Control |
| 2 | Tone Control (T) | 9 | 4-Color LED-light (synchronizes with alarms) |
| 3 | On/Off Button (U) | 10 | On/Off Button |
| 4 | Warning LED-light (Right) | 11 | Tone Control |
| 5 | Volume Control (V) | ||
| 6 | Sensitivity Control (S) | ||
| 7 | 2.5mm DC-connection (for illuminated swinger) |
4. Setup
4.1. Battery Installation
Both the bite alarms and the receiver require one 9V battery each (batteries are not included). Follow these steps to install the batteries:
- Locate the battery compartment cover on the back of the bite alarm/receiver.
- Slide or unclip the cover to open the compartment.
- Connect a 9V battery to the battery clip inside the compartment, ensuring correct polarity.
- Place the battery into the compartment and close the cover securely.

4.2. Initial Power On and Pairing
After installing batteries, power on both the alarms and the receiver. The units are designed to automatically pair. Test the connection by activating an alarm.
5. Operating Instructions
5.1. Bite Alarm Operation
- Power On/Off: Press and hold the 'U' button (3) to turn the alarm on or off.
- Volume Control: Use the 'V' button (5) to adjust the alarm volume.
- Tone Control: Use the 'T' button (2) to change the tone of the alarm.
- Sensitivity Control: Use the 'S' button (6) to adjust the sensitivity to line movement. Higher sensitivity will detect smaller movements.
- LED Indication: The warning LED lights (1, 4) will flash and the alarm will sound upon a bite. The system features a 20-second latch light, meaning the LED will remain lit for 20 seconds after a bite, allowing you to identify which alarm was triggered.
- Swinger Connection: An extra 2.5mm DC-connection (7) is provided for an illuminated swinger (not included).

5.2. Receiver Operation
- Power On/Off: Use the On/Off button (10) to power the receiver.
- Volume Control: Use the 'V' button (8) to adjust the receiver's volume.
- Tone Control: Use the 'T' button (11) to adjust the receiver's tone.
- Bite Indication: The 4-color LED lights (9) on the receiver will synchronize with the corresponding bite alarm when a bite occurs. The receiver also features a 20-second latch light and a vibration alert for discreet notification.


6. Maintenance
- Cleaning: Wipe the units with a soft, damp cloth. Do not use harsh chemicals or abrasive cleaners.
- Storage: When not in use for extended periods, remove batteries from both the alarms and the receiver to prevent leakage and damage. Store the set in its protective case in a cool, dry place.
- Water Resistance: The units are waterproof, but avoid prolonged submersion. Ensure battery compartments are securely closed before use near water.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No power/Unit not turning on | Dead or incorrectly installed battery. | Check battery polarity, replace with a fresh 9V battery. |
| Alarm not sounding/Receiver not responding | Out of range, low battery, or pairing issue. | Ensure units are within 150m range. Check/replace batteries. Power cycle both units. |
| False alarms | Sensitivity set too high, wind, or water movement. | Reduce sensitivity using the 'S' button on the alarm. |
| Difficulty adjusting settings | Buttons not pressed correctly or unit malfunction. | Ensure firm presses. If issue persists, contact support. |
8. Specifications
- Model: B1235
- Type: Fish Bell/Alarm
- Material: ABS
- Power Source: 1 x 9V battery per unit (Alarms and Receiver)
- Operating Range: Over 150 meters (wireless)
- Features: Adjustable Volume, Tone, Sensitivity; 20-second Latch Light; Vibration Alert (Receiver); 2.5mm DC-connection for swinger (Alarms); Waterproof design.
- Bite Alarm Dimensions: Approximately 11.5 cm (Height) x 4.5 cm (Width)
- Receiver Dimensions: Approximately 11 cm (Height) x 6 cm (Width)
- Package Dimensions: 28 cm (Length) x 21 cm (Width) x 8 cm (Height)
- Package Weight: 0.494 kg
- Origin: Mainland China

9. User Tips & FAQ
- Adding More Alarms: The system is designed to be expandable. If you wish to add more alarms (e.g., a fourth yellow alarm), please contact the seller or manufacturer for compatibility and pairing instructions for individual components.
- Waterproofing: The alarms and receiver are designed to be waterproof, making them suitable for various weather conditions. However, always ensure battery compartments are sealed properly.
- Bite Indication: The alarms provide both visual (LED) and audible signals. The LED lights on both the alarm and receiver will indicate a bite. Some models may differentiate between a 'run' (line moving away from shore) and a 'drop back' (line moving towards shore) through distinct light patterns or sounds, but the primary indication is a general bite alert.
- Swinger Use: Utilize the 2.5mm DC-connection on the bite alarms to connect an illuminated swinger for enhanced visual bite indication, especially in low light conditions.
10. Warranty and Support
For any questions, technical support, or warranty claims, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.