Dancing Wings Hobby E30 PITTS

Contents

Dancing Wings Hobby E30 PITTS 450mm RC Airplane Instruction Manual

Model: E30 PITTS | Brand: Dancing Wings Hobby

Introduction

This manual provides comprehensive instructions for the assembly, setup, and safe operation of your Dancing Wings Hobby E30 PITTS 450mm RC Airplane. Please read this manual thoroughly before attempting to assemble or fly the model to ensure safe and enjoyable use.

Dancing Wings Hobby E30 PITTS 450mm RC Airplane
The E30 PITTS 450mm RC Airplane, a micro biplane model.

Safety Precautions

WARNING: This product is not a toy. It is a complex and sophisticated flying model. Your safety and the safety of others depend on how you operate it. Improper operation can cause serious injury. Not suitable for children under 14 years of age.

  • Do not fly around restricted locations such as airports, military bases, or residential areas.
  • Always perform a range check on the transmitter to ensure no interference.
  • Always turn on the transmitter first, then the receiver. Turn off the receiver first, then the transmitter.
  • If you are a beginner, seek assistance from experienced fliers.
  • Keep all relevant items out of reach of children.
  • While designed for rigid performance, if performing high-stress flying, you are responsible for reinforcing the body strength and controlling movement range.
  • This product may contain fiberglass and carbon-fiber reinforced plastic parts. Wear goggles or dust-proof clothing if needed to avoid eye and skin discomfort from dust.
  • Due to air traffic safety regulations, glue may not be included. Please purchase suitable glue (e.g., UHU, 502) from your local stationery store.

Specifications

FeatureDetail
Brand NameDancing Wings Hobby
Item NameE30 PITTS
MaterialPP Foam
Wingspan450mm
Length425mm
Flying WeightApprox. 57g
Control Channels4 channels
Flight Time5~10 minutes
Remote ControlYes
Power SourceElectric
Recommend Age14+ years
State of AssemblyUnassembled Kit
Operator Skill LevelBeginner, Intermediate, Expert
Indoor/Outdoor UseOutdoor
CertificationCE
  • Motor: MM1106 KV3800 brushless
  • ESC: 5A brushless
  • Servo: 2g *1pc + 1.7g *2pcs
  • Propeller: 5 Inch
  • Battery: 2S 7.4V 150-250mAh LiPo
  • Radio System: 2.4G 4CH above
E30 PITTS Specifications Diagram
Visual overview of E30 PITTS specifications including wingspan, length, flying weight, motor, ESC, LiPo, propeller, and channels.

Kit Contents

The E30 PITTS RC Airplane is available in two versions: KIT (E3001) and KIT+Motor+Prop+Servo+ESC (E3004).

E3001 KIT Version Includes:

  • 1x Dancing Wings Hobby E30 PITTS Airplane KIT

Note: All electronic devices and glue are not included in the E3001 KIT version.

E3004 KIT+Motor+Prop+Servo+ESC Version Includes:

  • 1x Dancing Wings Hobby E30 PITTS Airplane KIT
  • 1x MM1106 3800KV Motor
  • 1x 5A/2S ESC
  • 1x 5 Inch Propeller
  • 1x 2g Servo
  • 2x 1.7g Servo (1.00pin)

Note: Transmitter, receiver, battery, charger, and glue are not included in the E3004 version.

E30 PITTS Kit Contents Diagram
Diagram showing the various components included in the E30 PITTS kit, labeled A1, A2, B1, B2, B3, C, D1-2, E1-3, F, G1, G2, H1-2, I, J.

Assembly Instructions

1. Assemble the Fuselage

  1. Step 01-1: Spread foam glue evenly on the reverse sides of the two pieces of A1.
  2. Step 01-2: Spread foam glue evenly on both sides of A2.
  3. Step 01-3: Paste the glued A1 to both sides of A2, aligning the edges and corresponding spaces when pasting.

2. Assemble the Wing

  1. Step 02-1: Insert the E1 carbon sheet into the reserved groove on the bottom of the lower wing B2, and fix the carbon sheet in the groove with foam glue.
  2. Step 02-2: Power on the servo to center it, then install a flat servo arm. Cut off the servo bracket.
  3. Step 02-3: Turn over the wing glued in step 02-1. Install the servo and place the servo line to the front (as shown in the left image). Do not glue the servo at this stage.
  4. Step 02-4: Insert the lower wing into the reserved groove at the lower end of the fuselage. Adjust the center and the servo position, then apply foam glue to the connection to fix it.
  5. Step 02-5: Insert a small carbon sheet into the reserved slot of the tail wing and fix it with foam glue.
  6. Step 02-6: Insert the horizontal tail into the tail of the fuselage, and fix the joint with foam glue.
  7. Step 02-7: As shown in the left image, paste a piece of transparent glue on the steering rudder, and then paste the steering rudder to the tail of the fuselage, maintaining a 1mm spacing.
  8. Step 02-8: Use a small amount of foam glue at the connection point under the steering rudder and the fuselage.
  9. Step 02-9: Cut the steering rudder from the fuselage. Use a model knife to cut the connection between the steering rudder and the fuselage, and cut a 45-degree slope.
E30 PITTS Assembly Steps 02-6 to 02-9
Visual guide for wing and tail assembly, including steps 02-6 through 02-9.

3. Make the Connecting Rod

  1. Step 03-5 (Components): The connecting rod consists of a carbon rod (F), heat-shrinkable tube (J), and Z-shape steel wire (H1).
  2. Step 03-6 (Assembly): Cut a suitable length of heat shrinkable tube. Sleeve the Z-shaped steel wire and the carbon rod together. Heat the heat shrinkable tube to shrink it, then add a small amount of CA glue to reinforce it.
  3. Note: For the two connecting rods, only one end of the Z-shaped head should be made initially. The other end will be made after determining the position according to the distance between the upper and lower ailerons.

4. Install Servo and Connecting Rod

  1. Step 03-1: As shown in the image, install the servo in the middle of the fuselage, staggered up and down. Arrange the servo wires from the reserved holes to the same side.
  2. Step 03-2: Insert one end of the steel wire linkage into the servo arm, and the other end into the servo horn. Pre-install the servo horn on the aileron, and trim the pin length of the servo horn. After adjusting the servo horn, spread foam glue to fix the servo horn on the aileron.
  3. Step 03-3: After finishing the Z-shaped head, insert the Z-shaped head into the rudder horn, and glue the rudder horn to the rudder surface with foam glue.
  4. Step 03-4: Insert the finished Z-shaped end into the rudder arm of the steering gear. Then, refer to the position of the rudder horn on the tail to determine the appropriate length of the connecting rod, and cut off the excess carbon rod.
E30 PITTS Servo and Connecting Rod Installation
Detailed steps for installing servos and connecting rods, including Z-bend creation and attachment to control surfaces.

Power System Installation and Adjustment

  1. Install the motor on the motor mount and fix it with screws. Install the propeller saver on the motor. Then, paste the assembly to the head of the fuselage and fix it with foam glue.
  2. For receiver welding, refer to the welding plug on the left image, or weld it yourself according to the receiver manual. The AEO RX15x-E series all-in-one receiver is recommended.
  3. Paste the wing bracket on the abdomen of the fuselage and fix it with foam glue.
  4. Insert the carbon rod and install the wheels. Firmly fix at both ends.

For more detailed information on power system adjustment, please refer to the online manual: AEO RX15x-E User Manual

E30 PITTS Power System and Landing Gear Installation
Illustrations for motor, receiver, and landing gear installation.

Pre-Flight Checks

  • Check/adjust servo centering to ensure control surfaces are properly aligned.
  • Double-check the motor's spinning direction to ensure it is suitable for your model.
  • Set the center of gravity (CG) at the position marked in the manual. Add weight to the nose or tail if necessary for optimal flight performance.
  • Verify all internal equipment is correctly connected and secure. Check the heat-shrink covering material, screws, bolts, cabin, and canopy.
  • Check battery condition. Replace immediately if low voltage or damaged.
  • Ensure your transmitter-receiver device connections are correct. For advanced devices, you may simplify connections through settings.
  • If pairing the power system and transmitter-receiver for the first time, set the maximum throttle stroke as needed.

Control Directions Tests

Perform these tests to ensure your control surfaces respond correctly to transmitter inputs.

Control SurfaceRemote ActionAirplane Reaction
ElevatorLifting rod up (pull back)Elevator moves up
Lifting rod down (push forward)Elevator moves down
AileronSteering rod to the leftLeft aileron moves up, right aileron moves down
Steering rod to the rightLeft aileron moves down, right aileron moves up
RudderDirection rod to the leftRudder moves left
Direction rod to the rightRudder moves right

Control Surface Throws

  • Normal Flying:
    • Aileron: ±15°-30°
    • Elevator: ±15°
    • Rudder: ±15°
  • 3D Flying (if supported):
    • Aileron: ±40° or larger
    • Elevator: ±40° or larger
    • Rudder: ±40° or larger

For special models with V-tails, flaps, or leading-edge wings, use normal flight angles as a reference. If unsure or without expert guidance, test at small angles first to confirm settings.

Center of Gravity (CG)

The recommended Center of Gravity (CG) for the E30 PITTS is 125mm from the leading edge of the wing.

The battery placement shown in the diagram is a guide. Use a knife to cut the slot along the dotted line to place the battery. If your battery does not fit the hole, you do not need to cut it.

E30 PITTS Center of Gravity Diagram
Diagram illustrating the recommended Center of Gravity (CG) position at 125mm and suggested battery placement.

User Tips

No specific user tips were found in the provided reviews or Q&A content.

Troubleshooting

If you encounter issues during assembly or flight, please review the relevant sections of this manual. Common issues include incorrect servo centering, loose connections, or improper CG. Ensure all components are securely attached and functioning correctly. For electronic issues, double-check wiring and power connections.

Maintenance

Regular maintenance will extend the life of your E30 PITTS RC Airplane. After each flight, inspect the airframe for any damage, especially to the foam, control surfaces, and propeller. Check all screws and connections for tightness. Keep the model clean and store it in a dry, safe place away from direct sunlight and extreme temperatures. Periodically check battery health and charge levels.

Warranty and Support

For further assistance or detailed information, please refer to the official English manual PDF: Dancing Wings Hobby E30 PITTS Manual PDF.

Contact the seller or manufacturer for any warranty-related inquiries or technical support not covered in this manual.

© 2023 Dancing Wings Hobby. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.