Fisher & Paykel 900PT561, OPT944, OPT970, OPT844, 900PT913

Contents

User Manual: Fisher & Paykel AIRVO2 Healthcare Respiratory Humidification Therapy Circuits

Models: 900PT561, OPT944, OPT970, OPT844, 900PT913

1. Introduction

This manual provides essential information for the safe and effective use of Fisher & Paykel AIRVO2 Healthcare Respiratory Humidification Therapy Circuits. These circuits are designed for single use with compatible Fisher & Paykel AIRVO and MR850 humidification systems to deliver warmed and humidified respiratory gases to patients requiring respiratory support.

Always consult the instructions for use provided with your main AIRVO2 or MR850 humidification device for complete system setup and operation details.

2. Product Overview

The Fisher & Paykel AIRVO2 humidification therapy circuits are available in several configurations to suit different patient needs and interfaces:

  • 900PT561: Heated Breathing Tube and Chamber Kit
  • OPT944 (Medium): Optiflow+ Nasal Cannula
  • OPT970: Optiflow+ Tracheostomy Direct Connection
  • OPT844 (Medium): Nasal Cannula
  • 900PT913: (Specific type not detailed in packaging, but listed as an option)

These circuits are intended for prescription use only (Rx only).

3. Setup and Connection

Follow these general steps for connecting the humidification circuit. Refer to the specific packaging and the main device manual for detailed, model-specific instructions.

  1. Inspect Packaging: Before opening, visually inspect the sterile packaging for any damage. Do not use if the packaging is compromised.
  2. Open Packaging: Aseptically open the packaging and remove the circuit components.
  3. Connect Humidification Chamber (if applicable, e.g., 900PT561): Securely attach the humidification chamber to the main AIRVO2 or MR850 device according to its instructions. Ensure a tight seal.
  4. Connect Breathing Tube: Attach the heated breathing tube to the outlet of the humidification chamber and to the patient interface (nasal cannula or tracheostomy connection).
  5. Connect Patient Interface: Securely connect the appropriate patient interface (nasal cannula, tracheostomy direct connection) to the breathing tube.
  6. Position Patient Interface: Carefully position the nasal cannula or tracheostomy connection on the patient as instructed by a healthcare professional. Ensure a comfortable and secure fit.
  7. Verify Connections: Double-check all connections to ensure they are secure and free from leaks.
Packaging for 900PT561 Heated Breathing Tube and Chamber Kit

Figure 3.1: Packaging for 900PT561 Heated Breathing Tube and Chamber Kit, showing components.

Packaging for OPT944 M Optiflow+ Nasal Cannula

Figure 3.2: Packaging for OPT944 M Optiflow+ Nasal Cannula, showing components.

Packaging for OPT970 Optiflow+ Tracheostomy Direct Connection

Figure 3.3: Packaging for OPT970 Optiflow+ Tracheostomy Direct Connection, showing components.

Packaging for OPT844 Nasal Cannula

Figure 3.4: Packaging for OPT844 Nasal Cannula, showing components.

4. Operating Instructions

These circuits are components of a respiratory humidification system. Operation involves the main AIRVO2 or MR850 device. Once the circuit is correctly installed:

  • Ensure the main humidification device is powered on and set to the prescribed temperature and flow rate.
  • Monitor the patient's comfort and respiratory status.
  • Regularly check for condensation in the breathing tube and ensure proper humidification delivery.
  • For nasal cannulas (OPT944, OPT844), ensure the prongs are correctly seated in the nostrils and the head strap is secure but not overly tight.
  • For tracheostomy connections (OPT970), ensure a secure and comfortable fit to the tracheostomy tube.

Always follow the specific operating instructions provided by your healthcare professional and the main device's user manual.

5. Maintenance and Disposal

Important: All Fisher & Paykel AIRVO2 Healthcare Respiratory Humidification Therapy Circuits (900PT561, OPT944, OPT970, OPT844, 900PT913) are designed for Single Use Only.

  • Do Not Reuse: Reusing single-use devices can lead to cross-contamination, infection, and compromised performance.
  • Do Not Clean or Sterilize: These circuits are not designed for cleaning, disinfection, or sterilization. Attempts to do so may damage the components and render them unsafe for use.
  • Disposal: Dispose of the used circuit components according to hospital policy, local regulations, and guidelines for medical waste.

6. Troubleshooting

If you encounter any issues with the humidification therapy, first refer to the troubleshooting section of your main AIRVO2 or MR850 device manual. For problems specifically related to the circuit, consider the following:

  • No Flow/Reduced Flow: Check all connections for kinks or disconnections. Ensure the main device is operating correctly.
  • Excessive Condensation: Verify that the heated breathing tube is functioning. Ensure the humidification chamber is correctly filled and connected.
  • Patient Discomfort/Leakage: Re-adjust the patient interface for a better fit. Ensure the correct size and type of interface is being used.

If problems persist, immediately contact a healthcare professional or qualified service technician. Do not attempt to repair or modify the circuit components.

7. Specifications

Feature Detail
Product Type Respiratory Humidification Therapy Circuits
Compatibility Fisher & Paykel AIRVO and MR850 Humidification Systems
Usage Single Use Only
Flow Rate (Nasal Cannula/Tracheostomy) 10 - 60 L/min (for OPT944, OPT970)
Latex Free Yes (for OPT844, generally for all F&P circuits)
Manufacturing Origin New Zealand
Regulatory Compliance CE 0123 (Medical Device Directive)

Individual Model Details:

  • 900PT561 (Heated Breathing Tube and Chamber Kit): Production Date: 2021-11-05, Expiry Date: 2024-11-05, LOT: 2101880309
  • OPT944 M (Optiflow+ Nasal Cannula): Production Date: 2020-01-28, LOT: 2100992993, PN: 183043711_e
  • OPT844 M (Nasal Cannula): Production Date: 2020-03-10, Expiry Date: 2025, LOT: 2101035358

8. Warranty and Support

For warranty information, technical support, or to report any issues with your Fisher & Paykel AIRVO2 Healthcare Respiratory Humidification Therapy Circuits, please contact:

  • Manufacturer: Fisher & Paykel Healthcare Ltd., 15 Maurice Paykel Place, East Tamaki, Auckland 2013, New Zealand.
  • EU Authorized Representative: Fisher & Paykel Healthcare SAS, 10 Av. du Québec, Bât. F5, BP 512, 91946 Courtaboeuf Cedex, France.
  • General Contact (China): +86 20-3205 3486
  • Your Supplier: Accessories Export Store

Always provide the model number, lot number, and date of purchase when seeking support.

9. User Tips

  • Adhere to Prescriptions: Always use the device and circuits strictly as prescribed by your healthcare provider.
  • Regular Monitoring: Ensure regular monitoring of the patient and the device's performance as instructed by medical staff.
  • Proper Fit: A proper and comfortable fit of the patient interface is crucial for effective therapy and patient comfort. Avoid overtightening straps.
  • Storage: Store unused circuits in their original, unopened packaging in a cool, dry place away from direct sunlight.
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.