feyree Portable EV Charger Type2 32A 7KW EVSE User Manual

1. Introduction

This manual provides essential information for the safe and efficient operation of your feyree Portable EV Charger. It covers setup, usage, maintenance, troubleshooting, and specifications. Please read this manual thoroughly before using the device to ensure proper function and safety.

feyree Portable EV Charger connected to an electric vehicle, showing the control box and a smartphone displaying the app interface.

Figure 1: feyree Portable EV Charger in use with smartphone app control.

2. Safety Information

2.1. WARNING!

Avoid immersing the AC charging connection device in water.
Do not step on, pull, bend, or knot the charging cable.
Do not insert foreign objects into any part of the Charging vehicle connector.
Refrain from dropping the control box or placing heavy objects on its surface.
Do not install or use the charger near flammable, explosive, harsh, or combustible materials, chemicals, or vapors.
Ensure the operating ambient temperature of the equipment remains within the range of -30 °C to +55 °C.
Do not use the charger when you, the vehicle, or the charger is exposed to severe rain.
Do not use the charger if it is defective, appears cracked, frayed, broken, otherwise damaged, or fails to operate.
Do not use this product if the enclosure or the EV connector is broken, cracked, open, or shows any other indication of damage.
Do not attempt to open, disassemble, repair, tamper with, or modify the charger.
This product is exclusively designed for electric vehicle charging purposes.
Avoid using external wires or adapters.
This product must be well-grounded when used.
Never insert your fingers into the charging plug.
The EV charger is not user serviceable. Contact customer support for any repairs.
If the device fails to charge normally as per the operation manual, please contact the seller or consider a replacement.
Never allow children to play with the charger cable.
To avoid the risk of fire or electric shock, do not use this device with an extension cord.
Using a worn or damaged AC outlet may cause burns or start a fire.
Risk of explosion. This equipment has arc or sparking parts that should not be exposed to flammable vapors.
Risk of electric shock. Do not remove the cover or attempt to open the enclosure of the charger unit. No user-serviceable parts inside. Refer servicing to qualified service personnel.

2.2. CAUTION! Please Note Before Starting Charging

It is recommended that electrical outlets for your charger should be installed by a licensed and qualified electrician. Installation must comply with local codes.
This product must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to help reduce the risk of electric shock.
Ensure the power plug and socket are compatible before initiating the charging process.
Do not charge if the socket is damaged, rusty, cracked, or has a loose connection. In case the socket is dirty or wet, please disconnect the power supply first. Wipe the charging plug with a dry and clean cloth to ensure it is dry and free from any debris.
Verify that the charging connector, cable, control box, and plug surface are in good condition without any scratches, rust, breaks, or damages.

3. Product Overview

3.1. Control Box Dimensions

Diagram showing the dimensions of the feyree EV charger control box: 227mm length, 100mm width, 56.5mm thickness.

Figure 2: Control Box Dimensions (Length: 227mm, Width: 100mm, Thickness: 56.5mm)

3.2. Smart LCD and Button Functions

Close-up of the feyree EV charger LCD screen and control buttons. Buttons are labeled A, D, T. A is for Adjust Current, D for Set Delay Time, T for Set Charging Time.

Figure 3: Smart LCD and Button Functions

Button A: Adjust Current (Downward when in menu page)
Button D: Set Delay Time (0-15h) / Enter (when in menu page)
Button T: Set Charging Time (short press) / Enter Menu Page (long press for 10 seconds) / Back (when in menu page)

Note: The device cannot adjust the current during charging. Current must be set before charging begins.

3.3. LCD Display Information

Detailed view of the feyree EV charger LCD screen showing charging state, real-time temperature, charging voltage, current, power, power consumption, charging time, and delay time settings.

Figure 4: LCD Display Elements

The LCD screen provides real-time charging status and settings:

Charging State: Indicates if charging is active.
Set Current: Displays the selected charging current (e.g., 32A).
Real-time Temperature: Current operating temperature.
Charging Voltage: Current voltage.
Charging Current: Actual current being drawn.
Real-time Power: Instantaneous power consumption.
Power Consumption: Total energy consumed (kWh).
Charging Time: Duration of current charging session.
Set Delay Time: Configured delay before charging starts.
Set Charging Time: Configured duration for charging.
Wi-Fi State: Connection status (Connection waiting, Connect, Not connected).

4. Setup

4.1. App Installation

To utilize the smart features, download the companion app:

Download the "Tuya Smart" or "Smart Life" App from your smartphone's app store. The app icons are typically a green house for Smart Life and a blue 't' for Tuya Smart.
After downloading, open the app, ensure your phone's Wi-Fi and Bluetooth are enabled.
Select "Add Device" and follow the in-app instructions to complete the device pairing.

Screenshots of the Tuya Smart app showing steps to set up charging periods and schedule charging to save money during off-peak hours.

Figure 5: App setup for scheduling charging periods.

4.2. Wi-Fi Connection Reset

If you need to reset the Wi-Fi connection:

Long press the "T" button on the control box for 10 seconds to enter the Menu page.
Press "A" to select "Settings", then press "D" to enter.
Press "A" to select "Reset Wifi", then press "D" to confirm the reset.

Diagram illustrating the steps to reset the Wi-Fi connection on the EV charger control box using the A, D, and T buttons.

Figure 6: How to reset Wi-Fi connection.

5. Operating Instructions

5.1. Basic Charging Steps

Adjust Current: Tap button "A" to adjust the current before connecting the charger to the EV. The charging current set shouldn't be higher than the supply current to avoid safety hazards.
Plug in the Charging Connector: Connect the charging plug to your EV. Charging will begin automatically.

Table showing adjustable current settings from 8A to 32A and their corresponding estimated miles per hour charging rate.

Figure 7: Adjustable Current Settings and Charging Rates

5.2. Ending Charging

WARNING: Do not unplug the charger during charging.

There are several ways to stop charging:

Plan A (Automatic Stop): The charger will automatically stop charging when the car is fully charged. You can then safely unplug it.
Plan B (Power Switch): Turn off the power switch supplying the charger, then unplug the charger.
Plan C (Vehicle Control): Use the stop charging button or switch in your electric vehicle to stop charging, then unplug the charger plug.
Plan D (App Control): Click "Stop charging" in the feyree app, and then pull out the charger plug.

5.3. Smart Timing and Scheduling

The charger supports smart timing and scheduling features to optimize charging based on electricity rates:

Delay Charging: Press the "D" button on the control box to set a delay time (0-15 hours) before charging begins. This is useful for starting charging during off-peak hours.
Scheduled Charging via App: Use the "Tuya Smart" or "Smart Life" app to set weekly charging plans, similar to an alarm clock, to charge during specific periods (e.g., off-peak at night).

Diagram illustrating scheduled charging to save money by charging during off-peak periods, with a delay charging option from 1-15 hours.

Figure 8: Schedule Charging to save money.

5.4. App Remote Control

The app provides comprehensive remote control capabilities:

Real-time monitoring of charging status.
Remote control for delay/timed charging.
Remote control to start/end charging.

Smartphone screen showing the feyree app interface with options for setting current, delay time, charging time, and starting/stopping charging remotely.

Figure 9: App Remote Control Interface.

5.5. App Use Without Wi-Fi (Bluetooth)

The app can also be used via Bluetooth if Wi-Fi is unavailable:

Connect your phone and charger by hotspot the first time. Then you can control the charger by app through Bluetooth within 10 meters (requires your SIM card to have a signal).

Diagram showing how to connect the charger to a smartphone via hotspot for Bluetooth control when Wi-Fi is not available, allowing app control within 10 meters.

Figure 10: App control via Bluetooth.

6. Maintenance

To ensure the longevity and safe operation of your feyree EV charger, follow these maintenance guidelines:

Regular Cleaning: Keep the control box, cable, and connectors clean and free from dust, dirt, and moisture. Use a dry, clean cloth for wiping.
Inspect for Damage: Periodically inspect the entire charging unit, including the cable, plugs, and control box, for any signs of wear, cracks, fraying, or other damage. Do not use the charger if any damage is found.
Storage: When not in use, store the charger in a dry, cool place, away from direct sunlight and extreme temperatures.
Avoid Stress: Do not pull, bend, or knot the charging cable excessively. Avoid placing heavy objects on the control box.
Professional Servicing: The charger is not user-serviceable. Any repairs or modifications should only be performed by qualified service personnel.

7. Troubleshooting

This section provides solutions to common issues you might encounter. Refer to the LCD display for error messages.

7.1. LCD Error Messages (Single-phase)

Screenshots of the feyree EV charger LCD display showing various single-phase error messages like Error cp, Under Voltage, Over Voltage, Leakage, Over Current, Over TEMP, PE missing warns, Leakage self check, and Relay self check.

Figure 11: Single-phase LCD Error Messages

7.2. LCD Error Messages (Three-phase)

Screenshots of the feyree EV charger LCD display showing various three-phase error messages like Error cp, Under Voltage, Over Voltage, Leakage, Over Current, Over TEMP, PE missing warns, Leakage self check, and Relay self check.

Figure 12: Three-phase LCD Error Messages

7.3. Common Troubleshooting Table

Fault Name	Reason for Failure	Recommendations
Over Voltage	AC input voltage is too high	Ask an electrician to measure the input voltage of the charger's power distribution box. If the actual voltage is over 264V for a short time, wait for the power system to restore itself to the normal voltage range. If the actual voltage is over 264V for a long time, contact the local power supply department. If the actual voltage of the electrical system in your home is less than 264V, contact customer support.
Under Voltage	AC input voltage is too low	Ask an electrician to measure the input voltage of the charger's power distribution box. If the actual voltage is less than 85V for a short time, wait for the power system to restore itself to the normal voltage range. If the actual voltage is less than 85V for a long time, contact the local power supply department. If the actual voltage of the electrical system in your home is over 85V, contact customer support.
Over Current	AC input current is too high	Cut off the power of the charger's power distribution box right away. Check the charging plug for foreign objects and the car's on-board charger for abnormalities. After troubleshooting, reconnect the power supply. If the fault persists, contact customer support.
Over TEMP	Charger internal temperature greater than 85°C	Check that there is no other heat-generating equipment or devices next to the charging station and make sure that the ambient temperature is below 50°C. If the problem cannot be solved, contact customer support.
Elec leakage	Leakage is greater than specified values (TypeA: AC20mA/AC30mA, TypeB: AC 30mA+DC 6mA)	Cut off the power of the charger's power distribution box right away. Check the charging plug for foreign objects and check the car for electrical leakage. After troubleshooting, reset the leakage protector, reconnect the power supply. If the fault persists, contact customer support.
Leakage self check	The sensor for detecting leakage is abnormal	Cut off the power of the charger's power distribution box right away. Check whether the output cable of the charging station is broken or connected to ground. After troubleshooting, reconnect the power supply. If the fault persists, contact customer support.
PE Fault	Poor grounding or incorrect wiring	Cut off the power of the charger's power distribution box right away. Check if the charging station is grounded properly. After troubleshooting, reconnect the power supply. If the fault persists, contact customer support.
Err:cp	Charging plug CC/CP connection abnormality	Check if the wiring of the charging plug is correct. After troubleshooting, if the fault still exists, contact customer support.

8. Specifications

8.1. General Product Specifications

Attribute	Value
Brand Name	feyree
Charger Type	Portable Charger
Power	7KW
Voltage	85V-264V
Current	8A-10A-13A-16A-20A-25A-32A Adjustable (32A Max)
Numbers of phase	single phase
Type	Type2
RCD	TypeB AC30mA + DC6mA
IP Rating	IP66 (Charger Plug & Charger Box)
Operating Temperature	-30 ~ +55 °C
Cable Length	5m
Material	Copper alloy, silver plating
Weight	3KG
Dimensions (L x W x H)	38cm x 38cm x 8cm (Package) / 22.7cm x 10cm x 5.65cm (Control Box)

8.2. Detailed Charging Box Specifications

The following tables provide detailed specifications for different charger types and power ratings.

TYPE2 Specifications

Power Rating	7kW	11kW	22kW
APP	●	●	●
Leakage protection	TypeB AC 30mA+DC 6mA
Power supply system	Single Phase	Three Phase	Three Phase
Rated voltage	85V-264V	380V±20%	380V±20%
Rated current	8-10-13-16-20-25-32A	8-10-13-16A	8-10-13-16-20-25-32A
Input Frequency	50Hz/60Hz	50Hz/60Hz	50Hz/60Hz
Charger Plug	IP66	IP66	IP66
Charger Box	IP66	IP66	IP66
Working temperature	-30°C ~ +55°C	-30°C ~ +55°C	-30°C ~ +55°C
Storage temperature	-40°C ~ +80°C	-40°C ~ +80°C	-40°C ~ +80°C
Standby power	<3W	<3W	<3W
Working humidity	5%~95% non-condensation	5%~95% non-condensation	5%~95% non-condensation
Cable Specification	3G 6mm²+1*0.5mm²	5G 2.5mm²+1*0.5mm²	5G 6mm²+1*0.5mm²

GBT Specifications

Power Rating	7kW	11kW	22kW
APP	●	●	●
Leakage protection	TypeB AC 30mA+DC 6mA
Power supply system	Single Phase	Three Phase	Three Phase
Rated voltage	85V-264V	380V±20%	380V±20%
Rated current	8-10-13-16-20-25-32A	8-10-13-16A	8-10-13-16-20-25-32A
Input Frequency	50Hz/60Hz	50Hz/60Hz	50Hz/60Hz
Charger Plug	IP66	IP66	IP66
Charger Box	IP66	IP66	IP66
Working temperature	-30°C ~ +55°C	-30°C ~ +55°C	-30°C ~ +55°C
Storage temperature	-40°C ~ +80°C	-40°C ~ +80°C	-40°C ~ +80°C
Standby power	<3W	<3W	<3W
Working humidity	5%~95% non-condensation	5%~95% non-condensation	5%~95% non-condensation
Cable Specification	3G 6mm²+1*0.5mm²	5G 2.5mm²+1*0.5mm²	5G 6mm²+1*0.5mm²

TYPE1 Specifications

Power Rating	Level 2 - 7kW	Level 2 - 9.6kW	Level 2 - 12kW
APP	●	●	●
Leakage protection	TypeA(60Hz)AC 20mA / TypeA (50Hz)AC 30mA
Power supply system	Level 1 and Level 2	Level 1 and Level 2	Level 1 and Level 2
Rated voltage	85V-264V	85V-264V	85V-264V
Rated current	8-10-13-16-20-25-32A	8-10-13-16-20-25-32-40A	8-10-13-16-20-25-32-40-50A
Input Frequency	50Hz/60Hz	50Hz/60Hz	50Hz/60Hz
Charger Plug	IP66	IP66	IP66
Charger Box	IP66	IP66	IP66
Working temperature	-30°C ~ +55°C	-30°C ~ +55°C	-30°C ~ +55°C
Storage temperature	-40°C ~ +80°C	-40°C ~ +80°C	-40°C ~ +80°C
Standby power	<3W	<3W	<3W
Working humidity	5%~95% non-condensation	5%~95% non-condensation	5%~95% non-condensation
Cable Specification	3G 6mm²+1*0.5mm²	3G8mm²+2*0.5mm²	3G10mm²+2*0.5mm²

TS-NACS Specifications

Power Rating	Level 2 - 7kW	Level 2 - 9.6kW	Level 2 - 12kW
APP	●	●	●
Leakage protection	TypeB AC 30mA+DC 6mA
Power supply system	Level 1 and Level 2	Level 1 and Level 2	Level 1 and Level 2
Rated voltage	85V-264V	85V-264V	85V-264V
Rated current	8-10-13-16-20-25-32A	8-10-13-16-20-25-32-40A	8-10-13-16-20-25-32-40-50A
Input Frequency	50Hz/60Hz	50Hz/60Hz	50Hz/60Hz
Charger Plug	IP66	IP66	IP66
Charger Box	IP66	IP66	IP66
Working temperature	-30°C ~ +55°C	-30°C ~ +55°C	-30°C ~ +55°C
Storage temperature	-40°C ~ +80°C	-40°C ~ +80°C	-40°C ~ +80°C
Standby power	<3W	<3W	<3W
Working humidity	5%~95% non-condensation	5%~95% non-condensation	5%~95% non-condensation
Cable Specification	3G 6mm²+1*0.5mm²	3G8mm²+2*0.5mm²	3G10mm²+2*0.5mm²

9. User Tips

Current Adjustment: Remember to adjust the charging current using button 'A' *before* plugging the charger into your EV. The current cannot be changed once charging has started.
Delay vs. Charging Time: The 'Delay Time' sets how long the charger waits before starting. The 'Charging Time' sets the duration for which the charger will operate once it begins. Factor in both when planning your charging schedule.
App Control: For maximum flexibility, use the 'Tuya Smart' or 'Smart Life' app to schedule charging during off-peak hours and monitor your charging status remotely.
Bluetooth Backup: If Wi-Fi is unavailable, you can still control the charger via Bluetooth through the app after an initial hotspot connection, provided your phone has a SIM signal.
Wall Mounting: The charger's design suggests it can be conveniently mounted on a wall for a more permanent setup, though it is portable.

10. Warranty and Support

10.1. Customer Service Team

For any product-related issues, please contact our customer service team:

E-mail: tina@feyree.com

10.2. Warranty

feyree offers a Two-Year Warranty to customers who have purchased an original feyree product.

Lifetime Technical Support: In case of any product-related issues, we encourage you to reach out to us, providing pictures and videos for further assistance.

10.3. Exclusions

The warranty does not cover:

Any product damage resulting from failure to follow the recommended guidelines in this manual.
Damage caused by unauthorized disassembly of the machine or seeking maintenance from a non-designated service center.
Products not purchased as original feyree products.
Any modifications or do-it-yourself alterations carried out without guidance from a licensed electrician.

11. FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and uses can radiate radio frequency energy, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user's authority to operate the equipment.

The device has been evaluated to meet general RF exposure requirements. To maintain compliance with FCC's RF exposure guidelines, the distance must be at least 20cm between the radiator and your body, and fully supported by the operating and installation configurations of the transmitter and its antennas.

11.1. APP Download QR Code

Scan the QR codes below to download the companion app:

	Feyree Portable EV Charger F-OBM22-AC-1P32 User Manual Comprehensive user manual for the Feyree F-OBM22-AC-1P32 portable EV charger, detailing installation, operation, safety precautions, app connectivity, and technical specifications for electric vehicle charging.
	Feyree Portable EV Charger Instructions and Specifications Comprehensive guide for Feyree portable EV chargers, covering safety, operation, specifications for Type 2, GBT, Type 1, and TS-NACS connectors, control box details, troubleshooting, app usage, and warranty information.
	Feyree Portable EV Charger Instructions and Specifications Comprehensive guide to Feyree portable EV chargers, covering setup, operation, safety warnings, product parameters, app integration, and after-sale service.
	Feyree Portable EV Charger Instructions and Safety Guide Comprehensive instructions, safety warnings, technical specifications, and app usage guide for the Feyree portable electric vehicle charger. Learn how to install, operate, and troubleshoot your EV charger.
	Feyree Portable EV Charger Instructions & Safety Guide User manual for the Feyree Portable EV Charger (Model FR-BZ-0022), a 3.5KW EVSE charging cable with Type 2 connector and adjustable current. This guide provides essential safety precautions, product specifications, charging steps, troubleshooting tips, and after-sale service information for electric vehicle owners.
	Feyree EV Charging Station Manual: Features, Operation, and Troubleshooting Comprehensive manual for Feyree EV Charging Stations, covering product overview, technical parameters for Type 1, Type 2, and GB/T 20234 standards, operating instructions, key operations, troubleshooting, and indicator light definitions. Includes safety guidelines and app usage.