Liludin QS-1205CME-3A

Contents

User Manual

Mini DC-DC 12-24V To 5V 3A Step Down Power Supply Module

Model: QS-1205CME-3A

Brand: Liludin

1. Introduction

This manual provides instructions for the safe and efficient use of the Mini DC-DC 12-24V To 5V 3A Step Down Power Supply Module (Model: QS-1205CME-3A). This module is a non-isolated step-down (BUCK) converter with synchronous rectification, designed to convert higher DC voltages (4.5-24V) to a stable lower DC voltage (adjustable 0.8-17V or fixed 1.8V, 2.5V, 3.3V, 5V, 9V, 12V).

2. Safety Precautions

  • Ensure correct input voltage polarity. The module does not have built-in reverse polarity protection.
  • Do not short-circuit the output for extended periods.
  • Operate within specified temperature ranges. Higher temperatures may reduce output power.
  • Ensure adequate cooling, especially when operating at maximum output current (3A).
  • Handle with care to avoid damage to sensitive electronic components.

3. Setup and Connection

The module features input and output solder pads for connection. The welding hole spacing is 2.54 mm.

Top view of the DC-DC step-down module showing input and output pins

Figure 1: Top view of the module. Labels include EN (Enable), IN+ (Input Positive), GND (Ground), VO+ (Output Positive), and ADJ (Adjustable output selection).

Bottom view of the DC-DC step-down module showing fixed voltage selection pads

Figure 2: Bottom view of the module. Pads are labeled for fixed output voltages: 1.8V, 2.5V, 3.3V, 5V, 9V, 12V. The ADJ pad is for adjustable output.

3.1 Wiring Instructions

  • Input Connection: Solder your DC input voltage source (4.5V to 24V) to the "IN+" (positive) and "GND" (negative) pads.
  • Output Connection: Solder your load to the "VO+" (positive) and "GND" (negative) pads.
  • Enable Pin (EN): This pin controls the module's operation. By default, it is pulled high internally, meaning the module is operational. To stop the module, pull this pin low (approx. 0V). To enable, pull high (2-5V).

3.2 Output Voltage Selection

The module offers both adjustable and fixed output voltage options.

  • Adjustable Output: To use the adjustable output (0.8V-17V), do not bridge any of the fixed voltage pads. The output voltage can be adjusted via the onboard potentiometer.
  • Fixed Output: To select a fixed output voltage (1.8V, 2.5V, 3.3V, 5V, 9V, 12V), bridge the corresponding solder pad on the bottom of the module. For example, to get a fixed 5V output, bridge the "5V" pad.

4. Operating Instructions

Once connected, apply the input voltage. The module will convert it to the selected output voltage.

  • Input Voltage Range: DC 4.5V to 24V.
  • Output Current: Up to 3A. For continuous operation at 3A, ensure proper cooling. For typical loads like 1.5A with a 12V input, minimal heat is generated.
  • Efficiency: High conversion efficiency, up to 97.5% (e.g., 6.5V to 5V at 0.7A).
  • Quiescent Current: Ultra-low quiescent current of 0.85 mA, making it suitable for always-on applications like car battery connections without needing an additional switch.

5. Maintenance

The module is designed for long-term, reliable operation with minimal maintenance.

  • Keep the module clean and free from dust and debris.
  • Ensure proper ventilation, especially when operating at higher loads or in enclosed spaces.
  • Regularly inspect solder joints for any signs of corrosion or damage if the module is exposed to harsh environments.

6. Troubleshooting

ProblemPossible CauseSolution
No output voltage
  • Incorrect input voltage.
  • Input polarity reversed.
  • Enable pin (EN) is low.
  • Short circuit at output.
  • Module damage.
  • Verify input voltage is within 4.5V-24V.
  • Check input wiring for correct polarity.
  • Ensure EN pin is high or floating (default).
  • Disconnect load and check for short.
  • Replace module if damaged.
Unstable output voltage
  • Input voltage fluctuations.
  • Output current exceeds module capacity.
  • Poor connections.
  • Ensure stable input power supply.
  • Reduce load or ensure adequate cooling.
  • Check all solder joints and connections.
Module gets excessively hot
  • Output current too high.
  • Insufficient cooling.
  • High input-to-output voltage difference at high current.
  • Reduce load current.
  • Provide better ventilation or a heatsink.
  • Ensure operation within specified limits.

7. User Tips

  • When using the adjustable output, make small adjustments to the potentiometer and verify the output with a multimeter.
  • For automotive applications, the low quiescent current makes it suitable for direct connection to the car battery or ACC line without significant drain.
  • Consider adding an external diode for reverse polarity protection on the input if your application requires it, as the module does not include this feature.
  • Always test the module's performance across the full specified input voltage range with your specific load to ensure stable operation, especially at the higher end of the input voltage spectrum.

8. Specifications

ParameterValue
Module TypeNon-isolated step-down (BUCK) synchronous rectifier
Input VoltageDC 4.5V - 24V
Output Voltage (Adjustable)0.8V - 17V
Output Voltage (Fixed)1.8V, 2.5V, 3.3V, 5V, 9V, 12V
Output Current (Max)3A (with adequate cooling), 2.1A (long-running)
Conversion EfficiencyUp to 97.5% (e.g., 6.5V to 5V @ 0.7A)
Switching Frequency500KHz
Output Ripple~20mV (12V to 5V @ 3A, 20M-bandwidth)
Operating TemperatureIndustrial grade (-40°C to +85°C)
Full Load Temperature Rise40°C
Quiescent Current0.85 mA
Load Regulation±1%
Voltage Regulation±0.5%
Dynamic Response Speed5% 200uS
Output Short Circuit ProtectionNo long-term protection
Input Reverse Polarity ProtectionNone
Enable ControlYes (High work, Low stop)
Dimensions (L*W*H)20mm * 11mm * 5mm
Connection TypeWelding pads
Welding Hole Spacing2.54 mm
Efficiency curve graph for the DC-DC module

Figure 3: Efficiency curve showing output current vs. efficiency for various input voltages (VIN=6.5V, 12V, 19V, 24V). Efficiency peaks around 97%.

Oscilloscope screenshot showing output ripple

Figure 4: Oscilloscope display showing output ripple. The waveform indicates a frequency of 489.43KHz and an amplitude of 10.69mV, confirming low ripple.

9. Warranty and Support

For any issues or support inquiries regarding your Mini DC-DC Step Down Power Supply Module, please contact your retailer or the manufacturer directly. Please have your purchase details and model number (QS-1205CME-3A) ready when contacting support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.