Interest Maker LCR-TC1 LCR-T7

Contents

LCR-TC1 LCR-T7 Transistor Tester Multimeter User Manual

1. Introduction

This manual provides detailed instructions for the safe and effective use of your LCR-TC1 or LCR-T7 Transistor Tester Multimeter. This multi-function tester is designed for automatic detection of various electronic components including NPN and PNP bipolar transistors, N-channel and P-channel MOSFETs, JFETs, diodes (including double diodes), N and P-IGBTs, resistors, inductors, capacitors, thyristors, triacs, and batteries (0.1-4.50V). It also features automatic detection of Zener diodes (0.01-20V) and an IR decoder.

2. Safety & Warnings

Read all instructions before use to ensure safety and prevent damage.

  • Do not use with incompatible devices or accessories to avoid affecting product performance or damaging related equipment.
  • If the product shows any abnormal conditions such as smoke, unusual noises, or odors, immediately stop using it.
  • This product is not food-related. Keep it away from children and avoid accidental ingestion or touching of sharp parts (if any).
  • Warning: Built-in Li-ion Battery. It is strictly prohibited to immerse the tester in water or place it near a heat source!
  • Warning: For your personal safety, please strictly comply with the use of Li-ion Battery specifications and precautions!
  • Warning: Always be sure to DISCHARGE capacitors before connecting them to the tester! The tester may be damaged before you have switched it on!
  • Warning: We do not recommend using the tester to measure the battery! The battery voltage must be less than 4.5V, otherwise the tester may be damaged!

3. Setup

  1. Unboxing: Carefully remove the transistor tester and all accessories from the packaging.
  2. Protective Films: Remove all protective films from the device, especially from the display.
  3. Initial Charge: Ensure the device is sufficiently charged before first use. Connect the Micro USB cable to the charging port and a 5V power source. The charging indicator will be red while charging and turn green when fully charged.
LCR-TC1 and LCR-T7 Transistor Testers with included accessories
LCR-TC1 and LCR-T7 Transistor Testers with included accessories, including test clips and USB charging cable.

4. Operating Instructions

The tester features a TFT graphic display (160x128) for clear measurement results.

Video demonstrating the basic operation and component testing capabilities of the LCR-TC1/T7 Multi-function Tester.

4.1. Power On & Basic Measurement

In the power-off state, short press the multi-function key (Start button). The tester will turn on and automatically begin a measurement cycle.

Screen showing 'M-Tester Testing...' and battery voltage
The tester's display during power-on and initial testing, showing battery voltage.

4.2. Detecting Transistors and Other Components

In the power-off state or after a test is completed:

  1. Insert the component's leads into the transistor test area (ZIF socket) of the test seat.
  2. Press the locking handle to secure the component.
  3. Short press the multi-function key. The tester will automatically measure and graphically display the results.
Diagrams showing various transistor types and their pinouts as detected by the M-Tester
Examples of transistor types (BJT-NPN, BJT-PNP, N-E-MOS, P-E-MOS, N-D-MOS, N-E-IGBT, P-JFET) and their pinout diagrams displayed by the tester.
Diagrams showing various component types and their measurements as detected by the M-Tester
Examples of component types (N-JFET, Diode, Capacitor, Inductor, Resistor, Battery, Thyristor, Triac) and their measurements displayed by the tester.

4.3. Detecting Zener Diodes

When the device is turned off or the test is completed:

  1. Insert the Zener diode into the dedicated Zener diode test area.
  2. Press the locking handle.
  3. Briefly press the multi-function button.

Note: Do not put components in the Transistor test area when testing Zener diodes, otherwise the Zener diode cannot be tested!

Screen showing 'M-Tester Zener' with a Zener diode symbol and forward voltage
The tester's display showing a detected Zener diode with its forward voltage (Uf).

4.4. IR Decoder Function

After a component test is completed:

  1. Point an infrared remote control at the "IR" test hole of the tester.
  2. Press a button on the remote control.
  3. The tester will display the user code and data code after successful decoding, along with the corresponding infrared waveform.

Note: This decoder only supports infrared encoding in Hitachi format. Other formats of infrared encoding are not supported.

If decoding fails, the user code and data code will not be displayed. If you are in the tester interface, you cannot enter the infrared decoding interface. If you are already in the infrared decoding interface, the last successful decoding information will remain displayed.

Screen showing 'M-Tester IR Decoder' with user code and data code
The tester's display showing the IR decoder function, with user code and data code.

4.5. Automatic Calibration

To perform automatic calibration:

  1. Short-circuit the three test sockets (pins 1, 2, and 3).
  2. Short press the multi-function button. The tester will automatically calibrate.

During the calibration process, there is no need to perform other operations except to disconnect the short wire according to the prompts on the screen.

Screens showing the calibration process from 3% to 100% completion
The calibration process displayed on the tester screen, showing progress and instructions to isolate probes.

4.6. Battery Voltage Measurement

Before each component measurement, the built-in lithium battery voltage will be detected and displayed. If the battery voltage is less than 3.1V, the tester will automatically shut down. Please charge the device at this time.

Screen showing 'M-Tester Charge the battery!' with battery voltage 3.1V
The tester's display indicating a low battery and prompting for charging.

4.7. Battery Charging

The charging interface is a standard Micro USB port. Use an external 5V power supply or a USB power source for charging. The charging indicator light will be red while charging and turn green when charging is complete.

4.8. Automatic Shutdown

The tester features automatic shutdown after a timeout period (default 30 seconds) if no operation is performed or after a component test/IR decoding is completed. Standby power consumption is 0 μA after shutdown.

5. Specifications

AttributeValue
Product NameTRANSISTOR TESTER
Model NumberLCR-TC1 LCR-T7
Brand NameInterest Maker
Dimensions70*90*27MM
Operating ModeManual Range
Operating Temperature0 - 40 ℃
Measuring Capacitance Range25pF-100mF
Measuring Resistance Range0.01-50MΩ
Measuring Inductance Range0.01mH-20H
CertificationCE
DIY SuppliesElectrical
OriginMainland China
Battery IncludedYes
Semi-finished productNo
High-concerned chemicalnone
Is Smart Deviceno
DC CurrentESR
AC CurrentMOSFET
DC Voltage3.7V
Display TypeDigital Display
AC Voltagemultimeter
Measurement range 1Diode/Triode/Double diode/Zener diode
Measurement range 2Field-effect transistor/Thyristor/Bidirectional thyristor
Measurement range 3Capacitance/Resistance/inductance

6. User Tips

  • Always discharge capacitors before connecting them to the tester to prevent damage.
  • This tester is highly useful for quickly identifying unknown components and their values, especially for resistors.
  • It provides good accuracy for determining if a component is functional or not, making it valuable for electronics repair.
  • If you experience inaccurate measurements, perform an automatic calibration as described in section 4.5.
  • Consider adding a metallic bar under the ZIF socket for easy capacitor discharge, as suggested by some users.

7. Troubleshooting

7.1. Common Issues & Solutions

  • Cannot Power On:
    Cause: Lithium battery is low.
    Solution: Charge the device using the Micro USB cable until the charging indicator turns green.
  • Inaccurate Measurements:
    Solution: Re-calibrate the tester (refer to section 4.5).

7.2. Known Errors and Limitations

  • The current amplification factor of germanium transistors may be measured too high due to high residual current. In this case, the base-emitter voltage will be very low.
  • Capacity value in reverse direction for Power Schottky Diodes (e.g., MBR3045PT) may not be measured if only one diode is connected. This is due to a large residual current. Sometimes, cooling the device (e.g., with cooling spray) can help.
  • The diode function of a triac gate cannot be examined.
  • The Source and Drain pins of JFETs may not be detected correctly due to the symmetrical structure of these semiconductors. The display may show the same layout with the same parameters if the Source and Drain pins are swapped.
  • The output current of the tester is 6mA and voltage is <5V. High-power IGBTs, thyristors, and Darlington tubes that require higher current/higher voltage drive may not be measured.
  • Air core coils and power inductors cannot directly measure inductance. It is recommended to try series connection for appropriate color ring inductance tests.
  • For capacitors below 20pF, it is recommended to test them with a known 20pF capacitor for comparison or calibration.

8. Maintenance

  • Keep the device clean and dry. Avoid exposing it to dust, dirt, or moisture.
  • Store the tester in a cool, dry place away from direct sunlight and extreme temperatures.
  • Regularly check the charging cable for any signs of damage.
  • No user-serviceable parts inside. Do not attempt to disassemble the device.

9. Manufacturer & Support Information

Manufacturer Information:

  • Country: China
  • Telephone: 86-13417026232
  • Email: xinhui0518@163.com
  • Responsible Person: Ouyanghui

EU Representative Information:

  • Representative: eVatmaster Consulting GmbH
  • Address: Bettinastr. 30, 60325 Frankfurt am Main, Germany
  • Email: contact@evatmaster.com
  • Telephone: +49-6995179070

For further assistance or inquiries, please contact the manufacturer or the EU representative using the provided contact details.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.