1. Introduction
This manual provides comprehensive instructions for the Beitian RTK GNSS Module, including models such as BT-982G2, BT-922G1, and BT-982G3. This small-size, high-precision positioning and orientation module is independently developed by Beitian, supporting full-system and all-frequency point satellite navigation. It is designed for applications requiring high accuracy, such as precision agriculture, intelligent driving, surveying, and mapping.

The module integrates advanced RF baseband and high-precision algorithms, supporting various global navigation satellite systems (GNSS) including BDS-2, BDS-3, GPS, GLONASS, Galileo, and QZSS. It features anti-interference capabilities, a backup power input for hot start functionality, and supports a sleep working mode to optimize power consumption. Software upgrades can be performed via the serial port.
Video 1.1: An animated overview of the Beitian RTK GNSS module's features and design.
2. Specifications
The Beitian RTK GNSS module offers robust performance for high-precision applications. Key specifications are detailed below:

2.1 General Performance
- Chip: K922
- Frequencies: BDS B1I/B2I/B3I, GPS L1C/A/L2P/L2C/L5, GLONASS L1/L2, Galileo E1/E5a/E5b, QZSS L1/L2/L5.
- Reacquisition Time: 1 second
- Signal Tracking Sensitivity: -155dBm
- Signal Capture Sensitivity: -140dBm
- RTK Horizontal Accuracy: 0.8 cm + 1 ppm
- RTK Initialization Time: 5 seconds (D < 10km)
- Initialization Reliability: 99.9%
- Anti-interference: Suppresses narrowband and single tone radio interference signals, with a signal-to-interference ratio up to 60dB.
2.2 Electrical and Physical Characteristics
- Power Supply (VCC): DC 3.6V-5.5V (typical 5.0V)
- Current Consumption: 150mA/5.0V
- Baud Rate: 115200bps (default), configurable from 4800bps to 921600bps
- Output Level: TTL
- Dimensions: 66mm x 45mm x 10.8mm
- Weight: 17.5g
- Connectors: 2*1.25/6P lockable horizontal SMD socket, 1*1.00/4P lockable horizontal SMD socket
- Antenna Connectors: SMA-K
- Operating Temperature: -40°C to +85°C
- Storage Temperature: -40°C to +105°C
For a complete list of detailed specifications, please refer to the official user manual PDF.
Reference: Beitian RTK GNSS Module User Manual (PDF)
3. Installation Guide
Before installation, ensure all components are intact and free from damage. The module can be integrated into various systems. Users may also use other modules for installation in a similar manner.
3.1 Hardware Interface
The module features a VCC power input pin. A farad capacitor stores energy to supply power to the RTC circuit when the main VCC is off, preserving key information for hot start functionality.
Serial port interfaces include:
- J1 (1.25/6P with lock socket): RX1, TX1, GND, VCC, RX1-232, TX1-232
- J2 (1.25/6P with lock socket): RX2, TX2, GND, VCC, RX2-232, TX2-232
- J3 (1.00/4P with lock socket): Standby interface
The 7th pin of the welding port serves as the 1PPS signal interface, providing a second pulse signal output.


3.2 Connection Diagrams
The module supports both radio and wired connection methods for RTK positioning. Below are schematic diagrams illustrating typical connection setups.

For wired connections, ensure you have a serial port debugging line and a desktop/laptop with a serial port (Win7 and above) and relevant drivers installed.
4. Operating Instructions
The module's operation is indicated by several LEDs:
- PWR LED: Steady red when power is supplied.
- TX LED: Blinks blue when data is being output from the port.
- PPS LED: Not lit when not positioned; flashes blue after 3D positioning.
- RTK LED: Flashes when receiving or sending differential signals; off otherwise.
- PVT LED: Not lit when no satellites are searched; flashes continuously every 5 seconds, with the number of blue flashes indicating the number of satellites currently tracked.
4.1 Software Interface Protocol (UART)
The UART serial port (J1) is used for outputting NMEA data at the UTC second boundary. The host computer can switch the working mode and upgrade software via this serial port. The default baud rate is 115200bps, with a data format of 1 start bit, 8 data bits, 1 stop bit, and no parity bit.
The module supports NMEA 0183 information output. Common statements include GGA, GLL, GSA, GSV, RMC, and VTG, providing data such as time, location, number of satellites, GPS receiver operation mode, satellite information, and speed.
For detailed NMEA 0183 information output instructions and other data formats (ComNav Binary, CMR, RTCM2.X, RTCM3.X), please refer to the full user manual PDF.
5. Maintenance and Precautions
- Power Supply: Ensure the VCC power supply ripple is controlled within 150mA/5.0V to avoid interference.
- Baud Rate: Always match the host computer's baud rate with the module's baud rate.
- Welding: Control welding temperature carefully to prevent damage to the module.
- Hot Start: Verify that the backup power supply is normal to ensure the hot start function operates correctly.
- Physical Inspection: Regularly check for any loose or damaged components.
6. Troubleshooting
- No Power Indication (PWR LED off): Check power supply connections and ensure the voltage is within the 3.6V-5.5V range.
- No Data Output (TX LED not blinking): Verify serial port connections, baud rate settings, and ensure the module is receiving satellite signals.
- No Positioning (PPS LED off, PVT LED not flashing): Ensure the antenna is properly connected and has a clear view of the sky. Check for potential signal interference.
- Inaccurate Positioning: Confirm that differential correction data (RTCM) is being received if operating in RTK mode. Ensure the module is in an environment with minimal interference.
- Hot Start Failure: Check the backup power supply to ensure it is functioning correctly.
7. User Tips
- Compatibility: This module is known to work with Pixhawk flight controllers and Mission Planner software, making it suitable for drone and UAV applications.
- Antenna Placement: For optimal performance, ensure your GNSS antenna has an unobstructed view of the sky.
- Power Stability: Use a stable power source to prevent unexpected behavior or damage to the module.
8. Warranty and Support
Beitian is responsible for the safety, reliability, and performance of the module under specific conditions: assembly, expansion, readjustment, improvement, or repair performed by company-approved personnel, and usage in accordance with operating requirements.
For technical support, please visit the official Beitian website or contact your local distributor. The content of this instruction manual may be changed without prior notice.
Official Website: www.beitian.com
9. Product List
The standard package for the BT-982G2 series module typically includes:
- BT-982G2 Series Module: x1
- 1.25/6P serial cable with lock: x2
- USB to Type-C Cable: x1
Note: This list is for reference only; detailed configurations should be based on customer requirements and the specific model purchased.
