eletechsup LD3080SA

Contents

eletechsup LD3080SA 20W DC-DC Buck Constant Current LED Driver Module

Instruction Manual

1. Introduction

This manual provides comprehensive instructions for the eletechsup LD3080SA HB LED Driver Module. This DC-DC Buck Constant Current Converter is designed for driving High Brightness (HB) LEDs in various applications, including flashlights and headlights. It offers precise current control and supports Pulse Width Modulation (PWM) dimming for flexible lighting solutions.

2. Product Specifications

AttributeValue
Model NumberLD3080SA
Brand Nameeletechsup
TypeDC/DC Converters
Working VoltageDC 3.5-30V
Output Current0-330MA/500MA/660MA/910MA (Adjustable)
Maximum Output Power20W
Output FrequencyDC-DC
Output TypeSINGLE
Current RegulationThrough PWM control
Output Current AccuracyTypical 3%
Switching FrequencyUp to 1MHz
ProtectionInherent open-circuit LED protection, Soft Over Temperature Protection
Size20*15*6mm
Weight2.2g
CustomizationYes
OriginMainland China
CertificationNone

For a visual representation of the module's dimensions and weight:

Multiple views of the LD3080SA LED driver module, showing its compact size of 20x15x6mm and weight of 2.2g.

Image: Multiple views of the LD3080SA LED driver module, showing its compact size of 20x15x6mm and weight of 2.2g.

3. Package Contents

Depending on the version and quantity selected, your package will contain:

  • 1, 2, or 4 pieces of the DC 3.5-30V 330MA/500/660/910MA Step-down HB LED Driver Module.

An example of the module:

Front view of the eletechsup LD3080SA LED Driver Module.

Image: Front view of the eletechsup LD3080SA LED Driver Module.

4. Setup and Installation

The LD3080SA module supports various wiring configurations for different functionalities. Always ensure the power supply is disconnected before making any connections.

An overview of the three primary wiring diagrams is provided below:

Overview of three wiring diagrams for the LED driver module: Constant Current Drive, Constant Current Drive with Switch, and PWM Dimming Circuit.

Image: Overview of three wiring diagrams for the LED driver module, illustrating Constant Current Drive, Constant Current Drive with Switch, and PWM Dimming Circuit.

4.1. Wiring Diagram 1: Constant Current Drive Circuit

This configuration provides a constant current output to drive 1 to N LEDs. The input voltage range is DC 3.5-30V. The output current can be set to 330MA, 500MA, 660MA, or 910MA by changing the RCS resistance (refer to product specifications for details on current selection).

Wiring Diagram 1: Shows connections for a 330MA/500MA/660MA/910MA LED Constant Current Drive Circuit. DC 3.5-30V input connects to VIN and GND, and LED+ and LED- connect to 1-N LEDs.

Image: Wiring Diagram 1 for a 330MA/500MA/660MA/910MA LED Constant Current Drive Circuit. Input DC 3.5-30V connects to the module's VIN and GND terminals, and the LED output (LED+, LED-) connects to a series of 1 to N LEDs.

4.2. Wiring Diagram 2: Constant Current Drive Circuit with Switch

This setup adds a switch to control the power to the LED driver module, allowing for easy ON/OFF functionality while maintaining constant current to the LEDs.

Wiring Diagram 2: Shows connections for a 330MA/500MA/660MA/910MA LED Constant Current Drive Circuit with a switch. A switch is placed in series with the positive input line (DC 3.5-30V) to the VIN terminal.

Image: Wiring Diagram 2 for a 330MA/500MA/660MA/910MA LED Constant Current Drive Circuit with a switch. The switch is connected in series with the positive input from the DC 3.5-30V power supply to the module's VIN terminal.

4.3. Wiring Diagram 3: PWM Dimming Circuit

This advanced configuration allows for brightness control of the LEDs using a PWM signal. The module accepts a 5V/3.3V 100-20KHz PWM signal for dimming from 0 to the selected maximum current (330MA, 500MA, 660MA, or 910MA).

Wiring Diagram 3: Shows connections for a 0-330MA/500MA/660MA/910MA LED PWM Dimming Circuit. A PWM signal generator (e.g., SG11A02) provides a PWM signal to the DIM pin of the LED driver module, along with a 5V DC supply.

Image: Wiring Diagram 3 for a 0-330MA/500MA/660MA/910MA LED PWM Dimming Circuit. A PWM signal generator (such as SG11A02) is connected to the module's DIM pin, with its VCC connected to a 5V DC source and GND to the module's GND.

5. Operating Instructions

  1. Power Connection: Connect your DC power source (3.5V to 30V) to the VIN (positive) and GND (negative) terminals of the module.
  2. LED Connection: Connect your High Brightness LEDs in series to the LED+ (positive) and LED- (negative) terminals. Ensure the total forward voltage of the LED string does not exceed the input voltage minus the module's dropout voltage.
  3. Current Selection: The module's output current is determined by the onboard RCS resistance. The available current options are 330MA, 500MA, 660MA, and 910MA. To change the maximum drive current, the RCS resistance must be modified (advanced users only).
  4. ON/OFF Control (with switch): If using Wiring Diagram 2, toggle the external switch to turn the LED circuit ON or OFF.
  5. PWM Dimming: For brightness control, connect a 5V/3.3V 100-20KHz PWM signal generator to the DIM pin as shown in Wiring Diagram 3. Adjust the duty cycle of the PWM signal to control the LED brightness from 0% to 100%.

Example of a 330MA current setting:

LD3080SA LED Controller module with 330MA current option highlighted.

Image: LD3080SA LED Controller module with the 330MA current option highlighted, indicating one of the selectable constant current outputs.

6. Maintenance

  • Keep Dry: Protect the module from moisture and liquids to prevent short circuits and damage.
  • Cleanliness: Keep the module free from dust and debris. Use a soft, dry brush or compressed air for cleaning if necessary.
  • Temperature: Operate the module within its specified temperature range. Avoid extreme heat or cold.
  • Inspection: Periodically inspect connections for looseness or corrosion.

7. Troubleshooting

  • LEDs Not Lighting Up:
    • Check power input voltage (3.5-30V DC).
    • Verify LED polarity (LED+ to anode, LED- to cathode).
    • Ensure LEDs are connected in series correctly.
    • Confirm the total forward voltage of the LED string is within the module's operating limits.
    • Check for loose connections or damaged wires.
  • Incorrect Brightness/Dimming Issues:
    • If using PWM dimming, verify the PWM signal voltage (5V/3.3V) and frequency (100-20KHz).
    • Check the PWM signal generator connections to the DIM pin.
  • Module Overheating:
    • Ensure the output current does not exceed the module's maximum rating (20W).
    • Verify proper ventilation around the module.
    • Reduce the number of LEDs or the drive current if possible.
  • Intermittent Operation:
    • Inspect all solder joints and connections for cold joints or shorts.
    • Ensure stable input power supply.

8. User Tips

  • Heat Management: For higher current settings or prolonged use, consider adding a small heatsink to the module if space allows, especially if the ambient temperature is high.
  • LED Selection: Always match the LED driver's current output to the rated current of your LEDs to ensure optimal performance and longevity.
  • PWM Signal Quality: A clean and stable PWM signal is crucial for smooth dimming. Avoid noisy power sources for your PWM generator.
  • Polarity Check: Double-check all polarities (input power and LED connections) before applying power to prevent damage to the module or LEDs.

9. Warranty and Support

For any technical assistance or inquiries regarding the eletechsup LD3080SA LED Driver Module, please contact your retailer or the manufacturer's support channels. Keep your purchase receipt for any warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.