ZWO AM3N

Contents

ZWO AM3N Strain Wave Gear Mount User Manual

Compact, Efficient, and Portable for Precision Control

1. Product Introduction

Thank you for purchasing the ZWO AM3N Strain Wave Gear Mount. The AM3N is a portable mount designed specifically for astrophotography, offering larger load capacity, higher precision, better low-temperature tolerance, and improved cable management compared to its predecessor. It combines portability, accuracy, intelligence, and high performance to meet diverse astronomy needs.

ZWO AM3N Strain Wave Gear Mount
The ZWO AM3N Strain Wave Gear Mount, a compact and efficient astronomical mount.

Key Features:

  • High Precision: Equipped with a specialized astronomical strain wave gear, achieving high precision with a Periodic Error (PE) consistently within ±15 arc-seconds. Each unit undergoes a 360° PE test.
  • High Load Capacity: Weighing 4.1 kg (9.04 lbs), it supports up to 8 kg (17.64 lbs) without counterweights and up to 13 kg (28.66 lbs) with counterweights.
  • Proprietary Control System: Software and hardware are independently developed by ZWO for stability and a customized user experience.
  • Dual-Mode: Offers both equatorial and alt-azimuth modes for imaging and visual observation.
  • No Regional Limitations: Designed with a 0-90-degree latitude scale for use at the equator and polar regions.
  • Hand Controller/APP Control: Basic and important functions (Tonight's Best, target GOTO, real-time star database) are accessible via Wi-Fi and Bluetooth through the mobile app ASI Mount. Firmware upgrades can also be done via the app.
  • Cable Management: Integrated DC output and Type-C port on the dovetail plate prevent cable entanglement.
  • Low-Temperature High-Load Mode: Can be activated in the APP to enhance load capacity in cold environments (-20 °C to 40 °C).
  • One-click Mechanical Zeroing: Supports a one-click return to the zero position from any state.
  • Power-off Brake Device: RA axis has brake protection to prevent equipment damage in case of power failure.
  • APP/PC Software Compatibility: Mobile devices use "SkyAtlas" or "ASIAIR" APP; computers support ASIStudio, ASCOM, and INDI platforms.

2. Safety Tips and Precautions

Please read the following tips carefully before using the ASI Mount to ensure safe and efficient operation.

  1. Solar Observation: Never observe the Sun directly with the naked eye through the telescope or finder scope. Always use a dedicated solar filter to prevent permanent eye damage.
  2. Tripod and Counterweight Selection: Choose a suitable tripod and counterweight based on the telescope's size and weight. Improper balancing can cause tipping, leading to equipment damage or personal injury. Test the center of gravity in multiple directions before use.
  3. Zero Position: If the mount is powered on while not at the zero position, return it to the home position before any operation. After use, return the mount to the home position before powering it off to prevent inaccurate positioning or malfunction.
  4. Child Safety: Keep children away from the mount to prevent tipping or injury. Small parts can pose a choking hazard.
  5. Environmental Conditions: Avoid placing the mount in high humidity or high salinity environments to prevent corrosion, reduced accuracy, short circuits, and permanent damage.
  6. Cleaning: Do not use corrosive solutions to clean the mount. Avoid prolonged exposure to direct sunlight to prevent discoloration.
  7. Disassembly: Do not attempt to disassemble the mount alone. This can damage the mount, reduce accuracy, and cause personal injury.
  8. Handling: The mount is a precision instrument; handle it with care to avoid knocking and damaging it.
  9. Operating Temperature: General Mode: 0 °C to 40 °C. Low Temperature Heavy Duty Mode (activated in software): -20 °C to 40 °C. Do not use outside this range. Store in original packing box for extended periods of disuse.

3. Packing List

The following items are included in your ZWO AM3N package:

  • Foam packaging box x1
  • Mount unit x1
  • 2-meter USB 2.0 cable (Type-B to Type-A) x1
  • 1-meter USB 2.0 cable (Type-C to Type-A) x1
  • ASI Mount periodic error test report x1
  • Quick start guide x1
  • Hand Controller x1
  • 2-meter hand pad connection cable x1
  • M6 hex wrench x1 (included within the unit)
Contents of the ZWO AM3N packaging box
Contents of the ZWO AM3N packaging box, including mount, cables, hand controller, and documentation.

4. Specifications

Detailed performance parameters for the ZWO AM3N Strain Wave Gear Mount:

ZWO AM3N Performance Specifications Table
Table detailing the ZWO AM3N's performance specifications.
ItemDescription
Mount typeStrain Wave Gear Mount
Mount modeEquatorial / Alt-Azimuth
DriveStrain Wave Gear + synchronous belt (300:1 reduction ratio)
Periodic error< ±15"
PE duration288 s
Drive (R.A.)Stepper motor + synchronous belt + 14 type 100 reduction ratio strain wave gear + brake
Drive (DEC)Stepper motor + synchronous belt + 14 type 100 reduction ratio strain wave gear
Payload8 kg (17.64 lbs) (without counterweight) / 13 kg (28.66 lbs) (with counterweight) @25 cm
Mount weight4.1 kg (9.04 lbs)
Altitude adjustment range0°-90°
Azimuth adjustment range± 6°
Dovetail saddleLosmandy & Vixen
Interface thread for counterweight barM12x1.75 coarse thread
Resolution0.17"
Max slew speed6°/S
Slew speed0.5x, 1x, 2x, 4x, 8x, 20x, 60x, 720x (max speed in heavy duty mode), 1440x
Power portDC D5.5x2.1 mm, center positive (12V, no less than 3A)
Power consumption12V / 0.65A (Standby)
12V / 0.8A (Tracking)
12V / 1.3A (GOTO) (1.8A-Heavy Load Mode)
Autoguide portST4
Communication portUSB / Wi-Fi / Bluetooth
Zero positionMechanical
Operating temperature-20°C to 40°C (Enable low-temperature high-load mode in software when below 0°C for stable performance)
Power-off brakeR.A. axis
Cable managementSupported

5. Setup

5.1 Introduction to the ASI Mount Components

Detailed view of ZWO AM3N mount components and ports
Labeled diagram of the ZWO AM3N mount, highlighting various components and ports.
  1. Finder shoe slot mounting holes: For installing ZWO finder bracket, ASIAIR, and finder.
  2. Power switch: Turns the mount power on or off.
  3. Counterweight screw hole: For mounting counterweight bar and counterweights (M12×1.75 coarse thread).
  4. Altitude gear adjustment screw: A pair of screws on both sides of the mount. Loosen with M6 hex wrench, adjust altitude, then tighten.
  5. Altitude gear tension knobs: Loosen to adjust altitude, tighten after adjustment.
  6. Altitude gear fine adjustment knob: Rotate clockwise for higher altitude, counterclockwise for lower.
  7. Azimuth gear fine adjustment knobs: Rotate in opposite directions to adjust azimuth base. Keep slightly tightened to prevent wobbling.
  8. Dovetail saddle plate tension knobs: Compatible with Vixen and Losmandy style dovetails.
  9. Auto guide port: ST-4 compatible auto guide port.
  10. USB 2.0 port: USB-B 2.0 port for connecting devices and firmware upgrades.
  11. BT button/Bluetooth indicator light: Used for Bluetooth pairing. Steady blue indicates ready to connect.
  12. HC: hand controller port: For connecting the hand controller device.
  13. DC 12V Power Input port: Supports 12V/3A–5A power input. Buzzer alerts for low voltage (<10.8V).
  14. Mode indicator: Red for equatorial mode, green for alt-azimuth mode. Flashes red/green if time/location not synchronized.
  15. Altitude scale: Indicates current altitude from 0° to 90°.
  16. Dovetail saddle: For mounting telescope dovetail plate, compatible with Vixen and Losmandy standards.
  17. DC power port: DC 12V 5A, powers mount and external devices like ASIAIR.
  18. Type-C port: For controlling mount, firmware updates, and connecting to Type-C devices (e.g., ASIAIR) or a computer.

5.2 Mount Installation

5.2.1 Tripod Setup

If using the optional ZWO carbon fiber TC40 tripod, unfold it first.

Install the silver mounting plate: Remove the three M6 screws from the silver mounting plate on the tripod, then lock the mounting plate tightly onto the mount.

Installing the mounting plate onto the ZWO AM3N
Close-up view of installing the mounting plate onto the ZWO AM3N base.

Install the ASI Mount onto the tripod: Place the AM3N with the silver mounting plate installed onto the tripod. Insert the multi-function support rod, rotate its knob clockwise to tighten it, then fit the tripod spreader and rotate its knob clockwise to lock it in place.

Steps for installing the ZWO AM3N mount onto a tripod
Step-by-step visual guide for installing the ZWO AM3N mount onto a tripod.

5.2.2 Optional Pier Extension Connection

If using a pier extension, mount it onto the tripod and tighten the knobs to secure it. Then, mount the AM3N body onto the pier extension and tighten its knobs.

Steps for connecting a pier extension to the ZWO AM3N mount
Visual instructions for connecting a pier extension to the ZWO AM3N mount and tripod.

5.2.3 Counterweight Bar / Counterweights Installation (Optional)

How to Determine Whether to Install Counterweights:

  • If the total weight of the telescope and associated equipment is less than 8 kg (17.64 lbs), the mount can be used without counterweights.
  • If the total weight exceeds 8 kg (17.64 lbs), counterweights are needed. The total weight should not exceed 13 kg (28.66 lbs).
  • The counterweight should be secured on a counterweight bar of no more than 25 cm (9.84 in) in length.
  • The counterweight bar has a threaded port with a coarse thread size of M12×1.75.

Counterweight Bar/Counterweights Installation Steps:

  1. Locate the counterweight mounting screw hole at the bottom of the ASI Mount unit.
  2. Unscrew the counterweight bar thread hole protective nut counterclockwise until it's completely removed, exposing the screw hole.
  3. Align the counterweight bar with the screw hole and rotate it clockwise to tighten it, then install the counterweights.
  4. Install the nut removed in step 2 onto the end of the counterweight bar.
Steps for installing counterweights on the ZWO AM3N mount
Visual guide for installing counterweights onto the ZWO AM3N mount.

5.2.4 ASIAIR Installation (Optional)

Install and secure the ZWO finder bracket onto the finder shoe slot mounting hole on the side of the telescope. Then attach the ASIAIR or finder to the bracket.

ZWO AM3N with ASIAIR installed on a finder bracket
ZWO AM3N mount with an ASIAIR unit attached via a finder bracket.

6. Operating Instructions

6.1 Introduction to the Hand Controller

Diagram of the ZWO AMH Hand Controller
Diagram of the ZWO AMH Hand Controller with labeled buttons and indicator light.
  1. Indicator light: Red light indicates high-speed mode (20-1440 times sidereal rate); off indicates low-speed mode (1, 2, 4, 8 times sidereal rate).
  2. Direction control joystick: Controls mount axes movement. Press down to switch between high and low speed modes.
  3. T button: Toggles tracking on/off. Red light on indicates tracking is active.
  4. Cancel button: Briefly press to cancel functions (e.g., stop GOTO). Press and hold for 3 seconds for Go Home position. For mode switching, press and hold while powering on until indicator light changes color.

6.2 Adjusting Altitude (0°-90° Scale)

The AM3N mount's altitude scales are divided into two gears:

  • First Gear (0° to 60°): Maximum adjustment angle is 60 degrees.
  • Second Gear (30° to 90°): For larger altitude angles.

To switch to Second Gear:

  1. Loosen the "altitude gear tension knob" on both sides.
  2. Rotate the "altitude gear fine adjustment knob" clockwise until the hex screw (the "altitude gear adjustment screw") is fully visible from the hole (approximately at the first gear, 40° position).
  3. Loosen both hex screws on the sides completely by turning counter-clockwise with an M6 hex wrench.
  4. Move the mount head to slide and adjust the "altitude gear fine adjustment knob". Slide the hex screw to the bottom end of the sliding rail in the hole, with the scale screw indicating 90°.
  5. Re-tighten the hex screws on both sides. (Note: Ensure gear screws are firmly tightened after adjustment to prevent loosening.)
  6. After completing the adjustment, tighten the altitude gear tension knobs.

It is recommended to switch the mount's gear when it is not carrying any weight.

Adjusting altitude on the ZWO AM3N mount
Visual steps for adjusting the altitude of the ZWO AM3N mount between its two gear ranges.

6.3 Adjusting the Azimuth Scale

Rotate the "azimuth gear fine adjustment knobs" in opposite directions to each other to adjust the azimuth scale. Keep the knobs slightly done up to prevent wobble.

ZWO AM3N mount showing DC 12V and Type-C ports
ZWO AM3N mount showing the DC 12V and Type-C ports on the dovetail saddle, relevant for power and control connections.

6.4 Switching Equatorial / Alt-azimuth Mode

Before switching modes, turn off the mount and remove any load.

  • To switch from equatorial mount mode to alt-azimuth mode: Connect the hand controller. Long-press and hold the [CANCEL] button, then turn on the ASI Mount. Wait until the indicator light turns green before releasing the [CANCEL] button. Adjust the ASI Mount's altitude angle to 90°.
  • To switch from alt-azimuth mode to equatorial mount mode: Connect the hand controller. Long-press and hold the [CANCEL] button, then turn on the ASI Mount. Wait until the indicator light turns red before releasing the [CANCEL] button. Adjust the ASI Mount's altitude angle to match your location's latitude.

Note: When installing the telescope in alt-azimuth mode, position the telescope tube to point to the left side (when the dovetail saddle plate tension knobs are facing upwards). Incorrect installation can lead to tracking errors during GOTO procedures.

Correct and incorrect telescope installation for alt-azimuth mode
Comparison of correct and incorrect telescope installation for alt-azimuth mode on the ZWO AM3N.

6.5 Controlling the ASI Mount

6.5.1 Control via PC

Preparation: Power on the ASI Mount and connect its USB port to your PC using a ZWO USB-B to USB-A 2.0 cable.

  1. Go to the ZWO official website: https://www.zwoastro.com/software/
  2. Download and install the ASCOM Platform and the ASCOM driver.
  3. Download and install software applications that support the ASCOM driver (e.g., ASI Studio, Maxim DL, NINA, SGP).
  4. In the mount section of your software, select "ASI Mount", click "Properties", choose the correct serial port, and click "Connect".
  5. Use the directional buttons in the software to control the mount's movement.
Screenshot of ASCOM interface for ZWO AM3N control on PC
Screenshots illustrating the ASCOM interface for controlling the ZWO AM3N on a PC.

6.5.2 Control via ASIAIR

  1. Secure the ASIAIR in a suitable location.
  2. After powering on the system, select the corresponding ASIAIR wireless signal in your mobile device's Wi-Fi settings.
  3. Open the ASIAIR APP, go to the mount selection page, choose "ZWO ASI Mount", and press the button to start the application.
  4. Return to the main page of the APP to set up or activate various devices and control the mount.
Screenshot of ASIAIR app interface for ZWO AM3N control
Screenshots demonstrating the ASIAIR app interface for controlling the ZWO AM3N.

6.5.3 Control via Bluetooth/Wi-Fi (SkyAtlas APP)

  1. Install the "SkyAtlas" APP: Scan the QR code provided in the official manual or download from the ZWO website.
  2. ASI Mount status confirmation: Check if the [BT] indicator light on the ASI Mount unit is constantly lit in blue. If not, restart the mount or press and hold the [BT] button for 5 seconds.
  3. Bluetooth Connection: Start the SkyAtlas APP, click the "1" icon for APP Settings, then "2" for "Choose Connection Method", and select "3" Bluetooth.
  4. Connection Confirmation: Connect to the required ASI Mount from the app's mount list. When the [BT] indicator light flashes during connection, press the [BT] button on the ASI Mount to confirm. The [BT] indicator will turn off upon successful connection.
  5. Wi-Fi Control: Power on the ASI Mount and Hand Controller. Connect your mobile device to the Hand Controller's Wi-Fi hotspot (typically named [AMH_XXXXXX]). Return to the app, and once the Wi-Fi connection is confirmed, you can control the mount.
Screenshot of SkyAtlas app interface for ZWO AM3N Bluetooth control
Screenshots showing the SkyAtlas app interface for Bluetooth control of the ZWO AM3N.

7. Maintenance

Proper maintenance ensures the longevity and optimal performance of your ZWO AM3N mount.

  • Cleaning: Do not use corrosive solutions to clean the mount. Avoid prolonged exposure to direct sunlight to prevent discoloration of the exterior oxide layer.
  • Disassembly: Do not attempt to disassemble the mount alone. Unauthorized disassembly can damage the mount, reduce its accuracy, and may cause personal injury.
  • Handling: The mount is a precision instrument. Handle it with care to avoid knocking and damaging it, which can reduce its accuracy.
  • Storage: If the mount will be unused for an extended period, store it in its original packing box in a dry environment.

8. Troubleshooting

Here are some common issues and their solutions:

  • Mount not at zero position on power-up: If the mount is powered on while not at the zero position, return it to the home position before performing any operation. This prevents inaccurate positioning or malfunction.
  • Hand Controller Wi-Fi password forgotten: If you forget the hand controller Wi-Fi password, you can reset it. While the ASI Mount is off, press and hold both the tracking and cancel buttons. Continue holding for 5 seconds after the mount powers on. The hand controller's indicator light will flash, indicating the password is reset to 12345678.
  • Indicator light flashing red/green: If the indicator light flashes alternately red and green after 5 seconds of constant illumination, you need to connect the ASI Mount to the relevant app or computer to synchronize location and time information. The light will revert to displaying the working mode status once synchronized.
  • Mount loosening after mode switch: After switching modes on the mount, always ensure you tighten the gear position adjustment screw firmly. Otherwise, the device may loosen.
  • Tracking errors in alt-azimuth mode: Ensure the telescope is installed correctly. When in alt-azimuth mode, the telescope tube should point to the left side (with dovetail saddle plate tension knobs facing upwards). Incorrect orientation can cause tracking errors.

9. Firmware Upgrade

The firmware of your ZWO AM3N mount can be upgraded via the mobile app, ASCOM platform, or ASIStudio.

9.1 Update Firmware with APP (SkyAtlas)

  1. Open the SkyAtlas APP and connect to the Hand Controller's Wi-Fi.
  2. Tap the mount icon to enter the setting page.
  3. Tap "AMH Management System" to enter the firmware update page.
  4. Enter the "NETWORK" section and enable WLAN to bridge the AM3N Wi-Fi to your home router network.
  5. Click "FIRMWARE" to initiate the update for either the Hand Controller or the mount.

9.2 Firmware Upgrade via ASCOM

  1. Connect the ASI Mount to your computer using a USB 2.0 cable.
  2. Open the ASCOM platform, select the correct "Serial Port", and click "Connect".
  3. Click "Firmware Update" to enter the firmware upgrade interface.
  4. Click "Open File" to select a local firmware package (downloaded in advance) or "Online Update" to download the latest firmware from the server.
  5. Wait for the firmware update process to complete.

9.3 Firmware Upgrade via ASIStudio

  1. Open ASIStudio on your computer and connect the ASI Mount using a USB 2.0 cable, ensuring the correct "Serial Port" is selected.
  2. Click the arrow icon to enter the firmware update page.
  3. Click "Install Manually" to select and install a local firmware update file (downloaded in advance).
  4. Alternatively, click "Online Update" to download and install the latest firmware directly from the internet.
  5. Wait for the firmware update process to complete.
Screenshots of firmware upgrade process via APP, ASCOM, and ASIStudio
Screenshots illustrating the firmware upgrade process via APP, ASCOM, and ASIStudio for the ZWO AM3N.

10. Structural Dimensions

The following diagrams provide detailed structural dimensions of the ZWO AM3N mount.

Mechanical diagrams illustrating the structural dimensions of the ZWO AM3N mount
Mechanical diagrams illustrating the structural dimensions of the ZWO AM3N mount.

11. User Tips

Based on user feedback and common questions, here are some helpful tips for using your ZWO AM3N mount:

  • Portability: The AM3N, especially when paired with a lightweight and stable tripod like the TC40, creates a highly mobile and easy-to-transport setup, perfect for field trips.
  • ASIAIR Integration: The AM3N integrates seamlessly with ASIAIR, making it an excellent choice for users who prefer a unified control system for their astrophotography rig.
  • Versatility: The mount is highly multifunctional and harmonic, capable of supporting various setups for both visual astronomy and advanced astrophotography.
  • Cable Management: Utilize the integrated Type-C and DC power ports on the dovetail saddle to keep your setup clean and prevent cable snags.

12. Warranty and Support

12.1 After Sales Service

For software upgrades, download updates directly from the official website: https://www.zwoastro.com/software/. For repairs and other services, contact ZWO support: https://support.zwoastro.com/.

  1. For products repaired or replaced within the warranty period, the user bears the cost of returning them. Provide valid proof of damage (pictures, videos) when sending back.
  2. For after-sales service, ZWO will provide an RMA code. Only products with an RMA number and ZWO's written confirmation will be accepted.
  3. If purchased from a ZWO agent, contact the agent directly for after-sales service.

12.2 Warranty Policy

ZWO provides a 2-year free warranty service. For ASI Mount products, the warranty period starts from the activation date of the user's equipment.

Damage-on-Arrival (DOA) Situations: If you encounter DOA situations and contact ZWO within the corresponding period with purchase invoices, ZWO will provide free postage and offer replacement, repair, or return services for:

  • Product quality problem: Within 180 days from receipt, if confirmed by ZWO customer service center.
  • Product transportation problem: If the outer packaging has obvious signs of water soaking or serious backlog and deformation upon receipt (provide pictures within three days).

Situations Not Covered by Warranty (Maintenance Services Available):

  • Product exceeds the warranty period.
  • Product exposed to liquid and corroded by moisture.
  • Product damaged by external force (scratches, deformation, broken USB port, etc.).
  • Dismantling, third-party maintenance, modification, refurbishment, or flashing wrong firmware without ZWO authorization.
  • Product system changed, or warranty label lost/changed.
  • Product quality problems due to failure to install according to usage requirements.
  • Physical damage and failure due to irresistible external forces (floods, fires, earthquakes, lightning strikes, strong vibrations, extrusions).
  • Damage caused by improper user operation.
  • No valid product purchase invoice or warranty certificate.
  • Product purchased as second-hand.

Quality problems with accessories or other product parts are not a condition for returning the host; users can request replacement of new accessories separately.

12.3 FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device. It generates, uses, and can radiate radio frequency energy. If not installed and used according to instructions, it may cause harmful interference to radio communications. If interference occurs, try to correct it by reorienting/relocating the receiving antenna, increasing separation between equipment and receiver, or connecting to a different circuit.

FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits for an uncontrolled environment. Maintain a minimum distance of 20 cm (8 inches) between the radiator and your body during normal operation.

12.4 ISED Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).

This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure. Users can obtain Canadian Information on RF exposure and compliance.

This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. Maintain a minimum distance of 20 cm between the radiator and your body.

For a detailed user manual in PDF format, please refer to the official ZWO website or the provided PDF link: ZWO AM3N User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.