Taidacent qi charging receiver module

Contents

Taidacent 4.2V 5W Wireless Charger Receiver QI Wireless Charge Receiver Magnetic Inductive Charging Receiver Battery Management

User Instruction Manual

1. Introduction

This manual provides detailed instructions for the Taidacent 4.2V 5W Wireless Charger Receiver module. This module is designed for integrating wireless charging capabilities into various projects, featuring battery charge and discharge management. It can directly supply power to other devices when connected to a battery.

2. Specifications

Feature Specification
Model Number qi charging receiver module
Accessory Type Charger Accessories
Origin Mainland China
PCB Size 36 x 18.5 x 2.8 mm (thickness)
Coil Size 41 x 29 x 1 mm (thickness)
Input Voltage 2.9V - 4.2V
Input Current (Max) 800mA
Output Power 5W
Efficiency (Max) 80%
Charging Indicator Blue light (always on during charging)
Full Charge Indicator Green light (always on when full)
Overcharge Protection 4.2V
Overdischarge Protection 2.9V
Short Circuit Protection Input and output short circuit protection

Note: Charging distance is determined by the transmitter used.

3. Product Components

Top-down view of the wireless charging receiver module, showing the PCB and the coil connected by wires.
Figure 3.1: Taidacent Wireless Charger Receiver Module (RXMODULE variant)

The module consists of a Printed Circuit Board (PCB) and a receiver coil, connected by thin wires. The PCB integrates the charging and battery management circuitry.

Top-down view of both the wireless charging transmitter and receiver modules, showing the larger transmitter PCB with coil and the smaller receiver PCB with coil.
Figure 3.2: Transmitter and Receiver Modules (TXRXMODULE variant shown for context)

The image above shows both the transmitter and receiver modules. This manual focuses on the receiver module.

Diagram showing the dimensions of the PCB (36x18.5mm) and the coil (41x29mm), with thickness measurements for both.
Figure 3.3: Module Dimensions

The PCB measures 36mm x 18.5mm with a thickness of 2.8mm. The receiver coil measures 41mm x 29mm with a thickness of 1mm.

4. Setup and Wiring

Careful wiring is essential for proper function and safety. Refer to the diagrams below for connection points.

Detailed view of the receiver module PCB, highlighting solder joints for battery connection (cathode and negative electrode) and wireless charging output.
Figure 4.1: Receiver Module Solder Joints

The image above indicates the following connection points on the receiver module:

  • Battery Solder Joints: These are for connecting a battery to the module. Ensure correct polarity: connect the battery's positive terminal to the "cathode" (marked as OUT+) and the negative terminal to the "negative electrode" (marked as OUT-).
  • Wireless Charging and Output Solder Joints: These are for connecting the module to the device it will power or charge. The "OUT" points are the main output terminals.

4.1 Connecting to a Battery and Load

Example wiring diagram showing the receiver module connected to a 3.7V 650mAh battery and then to a light bulb, demonstrating power output.
Figure 4.2: Example Wiring for Battery and Load

To connect the module to a battery and power a load (e.g., a light bulb):

  1. Solder the positive and negative terminals of your 2.9V-4.2V battery to the corresponding battery solder joints on the receiver module (OUT+ to positive, OUT- to negative).
  2. Connect your load (e.g., a light bulb, small fan, earphone) to the wireless charging and output solder joints (OUT).
  3. Ensure all connections are secure and observe correct polarity to prevent damage.

4.2 Connecting to a Transmitter for Wireless Charging

Example setup showing a transmitter module connected via USB, wirelessly charging the receiver module which is connected to a battery.
Figure 4.3: Wireless Charging Setup

To enable wireless charging:

  1. Ensure your receiver module is correctly wired to a battery and/or load as described in Section 4.1.
  2. Place the receiver coil in close proximity to a compatible wireless charging transmitter coil. The charging distance is dependent on the transmitter.
  3. The blue indicator light on the receiver module will illuminate when charging is active.

5. Operating Instructions

The Taidacent wireless charger receiver module operates automatically once correctly set up.

  • Charging: When the receiver coil is placed within the effective range of a compatible wireless transmitter, the module will begin charging the connected battery. A blue light on the module indicates active charging.
  • Full Charge Indication: Once the connected battery reaches a full charge (4.2V), the blue charging indicator will turn off, and a green light will illuminate, indicating the battery is fully charged.
  • Power Output: The module can directly supply power to connected devices from the battery, even while charging.

Important Remark: Do not carry a heavy load at the moment of power-on. This can cause damage to the module or connected components.

6. Maintenance

This module requires minimal maintenance. Follow these guidelines to ensure longevity:

  • Keep the module and coils dry and clean. Avoid exposure to moisture, dust, and extreme temperatures.
  • Handle the PCB and coil with care to prevent physical damage to components or wires.
  • Ensure proper ventilation if integrating into an enclosure to prevent overheating.

7. Troubleshooting

  • No Charging Indication (Blue Light Off):
    • Ensure the receiver coil is properly aligned with the transmitter coil.
    • Verify the transmitter is powered on and functioning correctly.
    • Check all wiring connections for looseness or incorrect polarity.
    • Confirm the input voltage to the receiver module is within the 2.9V-4.2V range.
  • Device Not Receiving Power:
    • Check the battery connection to the receiver module.
    • Verify the load is correctly connected to the output terminals.
    • Ensure the battery has sufficient charge.
    • Check for short circuits in the output wiring.
  • Overheating:
    • Ensure the module is not overloaded beyond its 5W output capacity.
    • Provide adequate ventilation around the module.
    • Check for any short circuits.

8. User Tips

  • For optimal efficiency, ensure the receiver and transmitter coils are as close as possible and perfectly aligned.
  • When integrating into a custom project, consider the module's dimensions and thickness for proper fit and heat dissipation.
  • Always double-check polarity before making any connections, especially when dealing with batteries.

9. Warranty and Support

For warranty information and technical support, please refer to the seller's policies or contact the manufacturer directly. Keep your purchase receipt for any warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.