XGEDA T550HVN08.2 CTRL BD 55T23-C03

Contents

T550HVN08.2 CTRL BD 55T23-C03 T-con Board User Manual

Model: T550HVN08.2 CTRL BD 55T23-C03 | Brand: XGEDA

1. Introduction

This manual provides instructions for the installation, operation, and maintenance of the T550HVN08.2 CTRL BD 55T23-C03 T-con (Timing Controller) board. This board is designed to control the timing and data signals sent to the LCD panel, ensuring proper image display. It is compatible with various Sony KDL series TV models, including KDL-50W800C, KDL-55W800C, and KDL-43W800C.

The T-con board is a critical component for your TV's display functionality. This product is a used component that has been rigorously tested by professional technicians to ensure it is in good working condition before shipment. Please read this manual carefully before attempting any installation or repair.

2. Safety Information

  • Always disconnect the TV from the power outlet before opening the back panel or performing any service.
  • Electronic components are sensitive to static electricity. Use anti-static precautions (e.g., anti-static wrist strap) when handling the T-con board.
  • Handle the board by its edges to avoid touching components or connectors.
  • If you are not experienced with TV repair, it is recommended to seek professional assistance.
  • Ensure the replacement board matches the original board's model number and specifications.

3. Setup and Installation

The T550HVN08.2 CTRL BD 55T23-C03 T-con board is designed for "plug and play" compatibility with specified Sony TV models. However, careful installation is crucial.

3.1 Pre-Installation Checks

  • Compatibility: Verify that your TV's original T-con board model number matches T550HVN08.2 CTRL BD 55T23-C03. Also confirm your TV's screen size (43, 50, or 55 inches) is supported.
  • Visual Inspection: Before installation, carefully inspect the new T-con board for any visible damage during shipping.
  • Original TV Issue: Ensure the original TV fault is indeed related to the T-con board (e.g., no picture, distorted colors, but backlight is on). If the LCD panel itself is faulty (e.g., physical damage, internal defects causing stripes or incorrect colors), replacing the T-con board will not resolve the issue.

3.2 Installation Steps

  1. Disconnect Power: Unplug the TV from the main power supply.
  2. Access TV Back Panel: Carefully remove the screws securing the TV's back panel and detach it.
  3. Locate T-con Board: The T-con board is typically located at the top center of the TV, often under a metal shield. Refer to the diagram below for typical component locations.
  4. Document Connections: Before disconnecting anything, take clear photos of all cable connections to the T-con board. Pay close attention to the LVDS cable (large ribbon cable from the mainboard) and the flex cables connecting to the LCD panel.
  5. Disconnect Cables: Gently unlatch and disconnect the LVDS cable and the flex cables from the old T-con board.
  6. Remove Old Board: Unscrew and remove the faulty T-con board.
  7. Install New Board: Place the new T550HVN08.2 CTRL BD 55T23-C03 T-con board into position and secure it with the screws.
  8. Reconnect Cables: Carefully reconnect the LVDS cable and the flex cables. Ensure they are seated correctly and latched securely. Note: Flex cables are typically not included with the T-con board and should be reused from your original setup unless damaged.
  9. Test (Optional): Before fully reassembling, you may perform a preliminary power-on test to check for basic display functionality. If successful, disconnect power again.
  10. Reassemble TV: Reattach the TV's back panel and secure all screws.
  11. Final Power-On: Plug the TV back into the power supply and turn it on to verify full functionality.
Diagram showing internal TV components and their locations

Figure 1: Typical internal layout of a TV, indicating the location of the T-con board, motherboard, power supply board, and screen number.

Close-up of the T550HVN08.2 CTRL BD 55T23-C03 T-con board

Figure 2: The T550HVN08.2 CTRL BD 55T23-C03 T-con board.

4. Operating Instructions

As an internal component, the T-con board does not require direct user operation. Once correctly installed, it functions automatically to process video signals and enable the TV display. If the installation is successful, your TV should power on and display images normally.

5. Maintenance

The T-con board is a sealed electronic component and requires no routine maintenance. To ensure its longevity:

  • Keep the TV in a well-ventilated area to prevent overheating.
  • Avoid exposing the TV to excessive dust, moisture, or extreme temperatures.
  • Do not attempt to clean the T-con board directly with liquids or abrasive materials.

6. Troubleshooting

If your TV does not function correctly after installing the T-con board, consider the following troubleshooting steps:

Problem Possible Cause Solution
No picture, but TV powers on (backlight may be on) Incorrectly seated LVDS or flex cables; faulty new T-con board; faulty mainboard or LCD panel.
  • Recheck all cable connections to ensure they are secure.
  • Verify the T-con board model matches your original.
  • If possible, test with another known good T-con board or consult a professional.
Distorted colors, lines, or partial image on screen (e.g., red faces, stripes) Faulty flex cables; damaged LCD panel; T-con board incompatibility or defect.
  • Inspect flex cables for damage or improper connection.
  • Confirm T-con board compatibility with your specific TV model and screen size.
  • If the issue persists, the LCD panel itself might be damaged (as noted by some users).
TV does not power on at all Issue not related to T-con board; faulty power supply board or mainboard.
  • Check power connections and TV's power supply.
  • The T-con board typically does not prevent the TV from powering on. Focus troubleshooting on power supply or mainboard.

7. Specifications

Feature Detail
Model Number T550HVN08.2 CTRL BD 55T23-C03
Product Type TFT (Thin-Film Transistor) T-con Board
Screen Type TFT
Display Size Compatibility >13 Inch (Specifically 43, 50, 55 inch Sony KDL series)
Origin Mainland China
Condition Used, tested and confirmed working before shipment. Circuit board components are intact.
Package Dimensions Length: 24 cm, Width: 9 cm, Height: 6 cm
Package Weight 0.12 kg

8. User Tips

  • Verify TV Panel Condition: Before purchasing and installing, ensure your TV's LCD panel is not the source of the problem. A faulty panel (e.g., with physical damage or internal defects causing persistent display issues like stripes or incorrect colors) will not be fixed by a new T-con board.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.