1. Introduction
This manual provides essential information for the safe and effective use of your Jikong JK Smart Battery Management System (BMS). The JK BMS is designed to protect and manage various lithium battery types, including LiFePO4, Li-ion, and LTO, in configurations from 4S to 8S. It features active balancing, Bluetooth connectivity for app control, and comprehensive protection functions.
The JK BMS is suitable for a range of applications, including RVs, solar energy storage systems, uninterruptible power supplies (SUP), and sightseeing buses.

2. Safety Information
- Always ensure correct wiring according to the provided diagrams. Incorrect wiring can damage the BMS, battery, or connected equipment.
- Do not use lead-acid battery chargers with lithium batteries managed by this BMS. Use only chargers specifically designed for lithium batteries.
- Ensure the BMS is installed in a dry, well-ventilated area, away from flammable materials.
- Avoid short circuits. Handle battery terminals and wiring with care.
- If the BMS shows signs of damage or malfunction, disconnect it immediately and seek professional assistance.
3. Product Overview
The Jikong JK Smart BMS is an on-board inverter BMS designed for robust battery management. Key features include:
- Built-in Bluetooth (BT): All JK BMS models include built-in Bluetooth for wireless monitoring and control via a smartphone app.
- Active Balancing: Features active equalization/balance to maintain cell voltage consistency, enhancing battery life and performance. Balancing current typically ranges from 0.4A to 2A depending on the model.
- Automatic Battery Identification: Automatically identifies and supports LTO, Li-ion, and LiFePO4 battery types.
- Comprehensive Protection: Offers 8 types of functional protection to safeguard your battery pack.
- Customizable Interfaces: Supports RS485 by default. CAN and other display interfaces are customizable and may require separate modules.


4. Setup
4.1 Wiring Instructions
Carefully follow the wiring diagram below to connect your JK BMS to your battery pack, charger, and load (controller). Ensure all connections are secure and correctly polarized.

Key Connections:
- B-: Total negative pole of the battery pack.
- P-: Common port for both charging and discharging negative electrodes. Connect your charger and controller negative terminals here.
- B+: Total positive pole of the battery pack.
- Balance Wires (1+ to 8+): Connect these wires to the positive terminals of each individual cell in your battery pack, starting from the lowest voltage cell (1+) up to the highest (8+).
- NTC: Temperature sensor connection.
- RS485/CAN/Display Interface: For communication and external display. RS485 is supported by default; CAN and other interfaces may require separate modules.
4.2 App Download and Connection
The JK BMS features built-in Bluetooth for easy monitoring and parameter adjustment via a dedicated smartphone application.
- Download the App: Scan the QR code located on your JK BMS unit to download the official application. The app is universally compatible with both Apple (iOS) and Android devices.
- Connect via Bluetooth: Once the app is installed, open it and search for your BMS via Bluetooth.
- Enter Passwords: The default connection password is 1234. The authorization password for making changes is 123456.


5. Operation
5.1 Basic Monitoring
Once connected via the app, you can monitor various parameters of your battery pack, including individual cell voltages, total voltage, current, temperature, and protection status.
5.2 Parameter Settings
The app allows for one-key setting of various parameters. This includes adjusting overcharge/overdischarge protection voltages, overcurrent limits, and other operational thresholds. Always understand the implications of changing these settings to avoid damaging your battery.
5.3 Active Balancing
The active balancing feature automatically engages when a cell voltage difference exceeds a set value, whether the battery is charging, discharging, or in a static state. This ensures that all cells in the pack remain balanced, prolonging the overall lifespan and efficiency of the battery.

6. Maintenance
- Regularly check all wiring connections for tightness and corrosion.
- Keep the BMS clean and free from dust and debris.
- Monitor battery parameters via the app periodically to ensure optimal performance and detect any anomalies early.
- Ensure proper ventilation around the BMS to prevent overheating.
7. Troubleshooting
7.1 Common Issues and Solutions
- BMS not connecting to app: Ensure Bluetooth is enabled on your device and the BMS is powered on. Double-check the connection password (1234).
- Battery not charging/discharging: Check for active protection (e.g., overcharge, overdischarge, overcurrent) indicated by the BMS. Verify all wiring connections, especially the P- terminal.
- Unbalanced cells: The active balancing feature should address this automatically. If persistent, check individual cell connections and the overall health of the battery pack.
7.2 FAQ about BMS Selection
(1) What is the difference between a 'same port' and 'split port' BMS?
- Same Port: The charging negative electrode and discharge negative electrode are connected to the same point (P-) on the protection board. This means charging and discharging share a single interface, and their currents are typically the same (e.g., 100A for both).
- Split Port: The charging negative electrode (C-) and the discharge negative electrode (P-) are separated and connected to different points on the protection board. This allows for different charging and discharging current ratings.
(2) How does battery capacity relate to the BMS current rating?
The battery capacity is not directly related to the continuous current rating of the BMS. The BMS current rating primarily depends on the continuous current draw required by your load (e.g., motor controller). The greater the current limit of your controller, the larger the continuous current of the selected BMS should be. Always choose a BMS with a current rating greater than your controller's current limit for a sufficient margin.
(3) What type of charger should I use?
Lithium batteries must be charged with a charger specifically designed for lithium batteries. Do NOT use lead-acid battery chargers, as this can cause high voltage breakdown of the BMS's MOS tube and lead to unprotected overcharging. The correct charger voltage is calculated as:
- LiFePO4 (Tieli) battery charger voltage: Number of battery strings × 3.65V
- Li-ion (Ternary) battery charger voltage: Number of battery strings × 4.25V
8. Specifications
The Jikong JK Smart BMS is available in various models with different current ratings and features. Below are general specifications and details for specific models:
| Technical Item | B1A8S10P | B1A8S20P | B2A8S20P |
|---|---|---|---|
| Battery Type | Li-ion/LiFePO4 | ||
| Strings | 4-8s | ||
| Equalizer Type | Active Equalization/Balance | ||
| Balance Current | 1A | 2A | |
| Main Circuit Conduction Internal | 0.3mΩ | ||
| Continuous output current | 100A | 200A | |
| Maximum output current | 200A | 350A | |
| Over Charge Protection Current (adjustable) | 10-100A | 10-200A | |
| Other interfaces (customizable) | RS485/CAN/Display interface | ||
| Wiring Output | Common port | ||
| Single Cell Voltage | 1-5V | ||
| Voltage Acquisition | ±5mV | ||
| Over Charge Protection Voltage | 1.2-4.35V Adjustable | ||
| Over Charge Release Voltage | 1.2-4.35V Adjustable | ||
| Over Current Detect Delay | 2-120S Adjustable | ||
| Over Discharge Protection Voltage | 1.2-4.35V Adjustable | ||
| Over Discharge Release Voltage | 1.2-4.35V Adjustable | ||
| Quantity of Temperature Detection | 3 pcs | ||
| Temperature Protection | Yes | ||
| Short Circuit protection | Yes | ||
| Coulomb counter | Yes | ||
| Bluetooth Function | APP For Android/IOS Available | ||

8.1 Model Specifics
Model: BD4A8S-4P
- Continuous Current: 40A
- Maximum Current: 60A
- Battery Strings: 4-8S
- Balance Current: 0.4A
- Battery Type: Li-ion/LiFePO4/LTO
- Product Size: 110*73*18mm
- Support: Built-in BT

New Product: JK-B2A8S30P
- Continuous Current: 300A
- Maximum Current: 450A
- Battery Strings: 4-8S
- Balance Current: 2A
- Battery Type: Li-ion/LiFePO4/LTO
- Product Size: 175*108*17.7mm
- Support: Built-in BT
- CAN or RS485: Requires separate purchase/consultation.

8.2 Physical Dimensions

9. User Tips
- The JK BMS is compatible with Android and iOS devices for app control and monitoring.
- When selecting a BMS, consider the continuous current requirements of your application rather than just the battery capacity.
- Always use a lithium-specific charger to prevent damage to the BMS and battery.
- For models with optional CAN or RS485 communication, ensure you purchase the necessary modules separately if required for your setup.
10. Warranty & Support
For technical support, troubleshooting assistance, or warranty inquiries, please contact your vendor or refer to the official Jikong website. Keep your purchase receipt for warranty claims.

11. Product Showcase Video
Watch this video for a visual overview of the Jikong JK BMS models and their features.