Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Hippcron Car Lock Door Remote Control Keyless Entry System. Please read this manual thoroughly before installation and use to ensure proper function and safety.
Figure 1: Complete Kit Components
Safety Precautions
- Always ensure the vehicle's power is disconnected before attempting any installation or wiring.
- Improper installation can lead to electrical shorts, damage to the vehicle, or malfunction of the system.
- Do not attempt to disassemble or repair the control unit or remote controls yourself. Refer to qualified professionals for service.
- Keep the control unit and remote controls away from water, high temperatures, and dust to prevent damage.
Installation Guide
Professional Installation Recommended: It is strongly advised to have this product installed by a professional automotive electrician technician.
Component Overview
- Control Box: The central unit for the keyless entry system.
- Remote Controllers: Two key fobs for remote locking and unlocking.
- Door Lock Actuators: Four units to convert manual door locks to automatic.
- Wiring Harness: For connecting all components.
- Mounting Accessories: Screws, brackets, and connecting rods.
Figure 2: Key Components - Control Box, Remote, and Actuator
Figure 3: Wiring Harness and Mounting Hardware
General Assembly Directions
- Before installing the central locking system, thoroughly understand the structure of the car door where it will be installed. Ensure the installation location does not affect the window's motion.
- After installing the lock, roll the window up and down a few times to ensure no scratching occurs. Then, replace the door panel.
- The controller is sealed with super-sonic waterproof materials. Do not attempt to disassemble or take apart the unit yourself. Seek an experienced or qualified professional for any internal issues.
- Ensure the host antenna is straightened and positioned away from metal parts to avoid affecting the remote control receiving distance.
- Install the host firmly. Ensure the wiring harness is long enough to avoid being pulled too tightly, which could cause issues during driving.
Wiring Diagram
The following diagram illustrates the connections for the control unit and door lock actuators. Pay close attention to wire colors and their corresponding functions.
Figure 4: System Wiring Diagram
- RED (10A FUSE): +12V Power
- BLACK: GND (Ground)
- BROWN: Connects to manual switch remote control system
- WHITE: Connects to manual switch remote control system
- BLUE/GREEN: Connect to door lock actuators (specific connections for drive seat and left/right after seat car doors)
- GREEN: Trunk release wire
- GULES (Red): Warning light
- ANT: Antenna wire (ensure it is straightened and not near metal)
Important: Wiring harness should avoid high temperature and high voltage positions. Secure all connections firmly with insulation tape.
Actuator Installation Examples
These examples illustrate how to install the door lock actuators within the car door panels.
- Front Driver-Side Door: Remove the door panel. Place the lock and metal piece on the metal board and stabilize it. Insert the connecting stick into the right side hole (refer to Figure 5, left image) and connect it straight down to the lock. Test by pulling the stick to see if it moves with other locks. (The front passenger-side assembly is similar).
- Rear Driver-Side Door: Place the lock and metal piece on the metal board and stabilize it (refer to Figure 5, right image). On the bottom left stabilizing hole of the door panel, insert the connecting stick into the hole on the right. Pull the stick down and extend it to find a suitable spot, then connect it to the lock. (The rear passenger-side assembly is similar).
Figure 5: Actuator Installation Details (Front and Rear Doors)
Figure 6: Actuator Installation Example
Operating Instructions
Basic Functions
- Lock: Press the lock button on the remote key fob to lock all central control doors.
- Unlock: Press the unlock button on the remote key fob to unlock all central control doors.
- Direction Light Flash: The direction lights will flash twice when locking and once when unlocking (JC-203 support).
- Manual Control: The system supports manual control switch lock (JC201 support) and manual control of the main driver lock, with linkage to other locks.
- Trunk Release: The remote key fob includes a button for trunk release. Connect the green wire from the control box to the trunk release mechanism.
Remote Control Learning Method (Pairing)
Follow these steps to pair your remote controls with the central unit:
- Press the host's "learning key" for 1 second. The LED light on the host will illuminate, indicating it's in learning mode. Any previously matched remote controls will be cleared.
- Press any button on the first remote control. If the host performs a lock action, the remote control has been successfully matched.
- Repeat step 2 for any other remote controls you wish to pair. The host can match up to four remote controls.
- The host will automatically save the remote control codes and exit the learning state after 15 seconds of inactivity.
Note: If you are having trouble pairing, ensure the remote control batteries are fresh (CR2016 type).
Maintenance
Battery Replacement
If the remote controlling distance becomes shorter or the indicator light on the remote becomes dimmer, it's time to change the battery.
- The remote controls use CR2016 type batteries.
- To replace, carefully open the remote control casing, remove the old battery, and insert a new CR2016 battery with the correct polarity.
- Close the casing securely.
Warning: Do not expose the main controller or remote controller to water or high temperatures. The control unit is sealed with waterproof materials; do not attempt to open it.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Remote control not working or not pairing. |
|
|
| Door locks not responding to remote or manual control. |
|
|
| System not functioning after installation. |
|
|
For complex issues or if you are unsure about any step, please consult a professional automotive electrician technician.
Specifications
| Feature | Detail |
|---|---|
| Brand Name | hippcron |
| Type | Anti-Theft Device One-Way |
| Feature | Remote Central Lock |
| Type of Remote Control | Without LCD Remote Control |
| Type of Accessory | Alarm Key Mold |
| Remote Control | Yes |
| Certification | CE |
| Origin | Mainland China |
| Control Box (Host) Specifications | |
| Working Voltage | 12V (±5V) |
| Static Current | <10mA |
| Operating Frequency | 433.92MHz |
| Receiving Sensitivity | -108dBm |
| Working Temperature | -20°C ~ +70°C |
| Control Box Size (L x W x H) | 8.6 x 6 x 2.5 cm |
| Remote Control Specifications | |
| Working Voltage | 6/12V |
| Static Current | <1uA |
| Transmission Power | 10dBm |
| Operating Frequency | 433.92MHz |
| Moving Distance | 18MM ±1MM |
| Movement Force | 32N ±4N |
| Remote Controller Size (L x W x H) | 6.2 x 3.3 x 1.2 cm |
| Operating Distance | About 30 - 80 meters |
| Battery Type | CR2016 (for remote controls) |
Note: This product does not have an alarm function.
Warranty and Support
Your Hippcron Car Lock Door Remote Control Keyless Entry System comes with a 1-year warranty from the date of purchase.
Warranty Claim Process
In case of a quality problem, wrong item received, or other issues, please contact customer support directly. Do not open a dispute immediately; contacting support first allows for a quicker resolution.
Figure 7: Warranty and Support Process
Additional Resources
An official user manual in PDF format is available for download. You can access it via this link: View User Manual (PDF).
User Tips
- Reliable Connectors: The product's connectors are designed for reliable and efficient performance, ensuring stable operation.
- Strong Signal: The system offers strong signal strength for reliable communication between the remote control and the central unit, typically ranging from 30 to 80 meters.
- Long Battery Life: The remote controls are designed for prolonged usage, reducing the frequency of battery replacements.
- Trunk Release Functionality: Utilize the dedicated button on the remote for convenient trunk access, provided the green trunk wire is correctly connected during installation.
Frequently Asked Questions (FAQ)
- Q: How is the connector performance of this system?
- A: The connectors are designed to offer reliable and efficient performance.
- Q: What is the battery life like for the remote controls?
- A: The product features a long battery life, ensuring prolonged usage without frequent replacements.
- Q: What functions does this keyless entry system have?
- A: It includes an anti-theft device feature and supports remote central locking, unlocking, and trunk release.
- Q: How strong is the signal strength?
- A: The signal strength is strong, allowing for reliable communication between the remote control and the device, with an operating distance of 30-80 meters.
- Q: What type of batteries do the remote controls use?
- A: The remote controls use CR2016 batteries.
- Q: How do I pair the remote controls with the central unit?
- A: Please refer to the "Remote Control Learning Method" section under Operating Instructions for detailed steps.
- Q: Does this system have a trunk release function?
- A: Yes, the remote control has a dedicated button for trunk release, which can be activated if the green trunk wire is correctly connected during installation.
- Q: Does this product include an alarm function?
- A: No, this product does not have an alarm function.
Product Video
Video: Overview and demonstration of the Hippcron Car Lock Door Remote Control Keyless Entry System.
