1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Dooya DC227A or DC228A RF433mhz Wall Switch. These switches are designed to control strong curtain motors and tubular blinds, offering convenient wall-mounted control and compatibility with Dooya RF433mhz remote controllers.
2. Product Overview
The Dooya DC227A and DC228A are wall-mounted RF433mhz receiver switches. The DC227A is a single-channel switch, suitable for controlling one motor. The DC228A is a dual-channel switch, capable of controlling two separate motors independently.
Both models are compatible with various motor types, including:
- 4-wire strong curtain motors (e.g., DT52S)
- Tubular motors (e.g., DM35S type)
- 5-wire curtain motors (e.g., DT82TV)
These switches are designed to work seamlessly with Dooya brand RF433mhz remote controllers for wireless operation.

Figure 1: Dooya RF433 Wall Receiver Wall Switch, showing DC227A (1 Channel) and DC228A (2 Channel) models.

Figure 2: DC228A controlling two motors in different rooms, demonstrating dual-channel capability.
3. Specifications
| Feature | Specification |
|---|---|
| Model Numbers | DC227A (Single Channel), DC228A (Dual Channel) |
| Voltage | 220V/50HZ |
| Transmission Frequency | RF433mhz |
| Dimensions | 86mm x 86mm (approx.) |
| Weight | 1984.6g (packaging weight) |
| Compatibility | Strong curtain motors (4-wire, 5-wire), Tubular motors |
| Customization | Yes |
| Origin | Mainland China |
| Rolling Speed | None |
| Wattage | None |
| Certification | None |
4. Setup and Installation
Important Safety Information: Installation should be performed by a qualified electrician or a person with sufficient knowledge of electrical systems. Ensure power is disconnected at the main circuit breaker before beginning any wiring work.
4.1 Package Contents
Before installation, verify that all components are present:
- Dooya DC227A or DC228A Wall Switch
- Mounting Screws
- Instruction Manual (this document)

Figure 3: Typical package contents for the DC228A wall switch.
4.2 Wiring Diagram and Connections
The switches feature clearly labeled terminals for power input and motor connections. Refer to the diagrams below for correct wiring. Ensure all connections are secure.

Figure 4: Rear view of DC227A (Single Channel) showing wiring terminals.

Figure 5: Rear view of DC228A (Dual Channel) showing wiring terminals for two motors.

Figure 6: Labeled components and wiring for DC228A. Note the 'Reset button' and 'indicator light'.
Terminal Labels:
- L: Live wire (220V AC)
- N: Neutral wire (220V AC)
- AC: AC power input (often connected to L and N)
- MOTOR1 (UP, STOP, DOWN): Connections for the first motor.
- MOTOR2 (UP, STOP, DOWN): Connections for the second motor (DC228A only).
Motor Compatibility Examples:

Figure 7: Example of wiring with a 4-wire motor (e.g., DT52S).

Figure 8: Example of wiring with a 5-wire motor (e.g., DT82TV).

Figure 9: Example of wiring with a tubular motor (e.g., DM35S).
After wiring, carefully mount the switch into the wall box using the provided screws.
5. Operating Instructions
Once installed and powered, the wall switch provides direct control over your connected motors.
5.1 Manual Operation
The front panel of the switch features three buttons for each channel:
- UP Button: Press to move the curtain/blind upwards.
- STOP Button: Press to stop the curtain/blind at its current position.
- DOWN Button: Press to move the curtain/blind downwards.
For the DC228A (dual channel), there will be two sets of these buttons, one for each motor.
5.2 Pairing with Dooya RF433mhz Remote Controller
To enable wireless control, you need to pair the wall switch with a Dooya RF433mhz remote controller. The exact pairing procedure may vary slightly depending on the remote controller model, but generally involves:
- Ensure the wall switch is powered on.
- Locate the 'Reset button' on the wall switch (refer to Figure 6).
- Press and hold the 'Reset button' on the wall switch until the indicator light flashes (or as per your remote's instructions).
- Within a few seconds, press the 'UP' button on your Dooya RF433mhz remote controller.
- The motor should jog slightly, and the indicator light on the wall switch may change, confirming successful pairing.
- Test the UP, STOP, and DOWN functions from the remote controller.
If pairing fails, repeat the steps. Consult your Dooya remote controller's manual for specific pairing instructions if needed.
6. Maintenance
The Dooya wall switch requires minimal maintenance to ensure long-term performance.
- Cleaning: Wipe the surface of the switch with a soft, dry cloth. Do not use abrasive cleaners, solvents, or excessive moisture, as this can damage the electronics.
- Environmental Conditions: Ensure the switch is not exposed to extreme temperatures, direct sunlight, or high humidity.
- Electrical Safety: Periodically check for any loose wiring connections. If any issues are observed, disconnect power before inspecting and tightening connections.
7. Troubleshooting
If you encounter problems with your Dooya wall switch, refer to the following common issues and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Motor does not respond to wall switch. | No power to the switch; incorrect wiring; faulty motor. | Check circuit breaker. Verify wiring connections (L, N, Motor). Test motor independently if possible. |
| Motor does not respond to remote controller. | Switch not paired with remote; remote battery low; remote out of range. | Re-pair the switch with the remote (Section 5.2). Replace remote battery. Ensure remote is within range (typically 20-30 meters indoors). |
| Motor moves in the wrong direction. | Motor wiring for UP/DOWN is reversed. | Disconnect power and swap the UP and DOWN motor wires at the switch terminals. |
| Indicator light on switch is off. | No power to the switch. | Check power supply and wiring to L and N terminals. |
8. User Tips
Here are some tips to enhance your experience with the Dooya wall switch:
- Remote Control Convenience: While the wall switch offers direct control, consider using a Dooya RF433mhz remote controller for added convenience, especially for hard-to-reach switches or for controlling multiple blinds from one location.
- Labeling: For DC228A dual-channel switches, consider labeling the buttons or the switch plate to clearly indicate which channel controls which motor, especially if they are in different rooms.
- Professional Installation: If you are unsure about electrical wiring, it is highly recommended to seek professional installation to ensure safety and correct functionality.
9. Warranty and Support
Your Dooya DC227A / DC228A Wall Switch comes with a limited warranty:
- Main Unit: 1-Year Manufacturer's Limited Warranty for defective items. This warranty does not cover items damaged due to misuse or improper installation after receipt.
- Accessories: 3-Month Warranty.
For warranty claims or technical support, please contact your retailer or the manufacturer with your order number and a description of the issue. Defective items must be reported and returned within the warranty period, preferably in their original packaging.