Mitutoyo 505-681

Contents

Mitutoyo Dial Caliper 505-681 User Manual

Precision Measuring Instrument

Introduction

Thank you for choosing the Mitutoyo Dial Caliper. This precision measuring instrument is designed for accurate and reliable measurements in various applications, particularly in metalworking and other DIY projects. This manual provides essential information for the proper setup, operation, maintenance, and troubleshooting of your caliper. Please read it thoroughly before use to ensure optimal performance and longevity of the tool.

Product Overview

The Mitutoyo Dial Caliper is a robust and accurate tool for measuring outside dimensions, inside dimensions, depths, and steps. It features a clear dial indicator for easy reading of measurements down to 0.01mm.

Video: Demonstration of the Mitutoyo Dial Caliper's smooth operation and packaging.

Close-up of Mitutoyo Dial Caliper's yellow dial showing 0.01mm accuracy

Figure 1: The precision dial indicator for accurate readings.

Full view of Mitutoyo Dial Caliper with yellow dial

Figure 2: The complete Mitutoyo Dial Caliper, ready for use.

Close-up of Mitutoyo Dial Caliper's beam showing serial number and 'STAINLESS HARDENED'

Figure 3: The hardened stainless steel beam with serial number for durability and authenticity.

Mitutoyo Dial Caliper in its case with a Certificate of Inspection

Figure 4: The caliper packaged with its official Certificate of Inspection.

Specifications

FeatureDescription
Brand NameMitutoyo
Model Number505-681 (0-150mm), 505-682 (0-200mm)
Caliper TypeDial Calipers
MaterialCarbon Steel (Stainless Hardened)
Accuracy0.01mm
Measurement Range0 - 150 MM (for 505-681), 0 - 200 MM (for 505-682)
DIY SuppliesMetalworking
OriginJapan
Battery IncludedNo
High-concerned chemicalNone
CertificationNone
Standard Temperature20°C

Setup

  1. Unpacking: Carefully remove the dial caliper from its protective case. Inspect for any visible damage.
  2. Cleaning: Before first use, wipe all measuring surfaces and the beam with a clean, lint-free cloth. A small amount of instrument oil can be applied to the sliding surfaces to ensure smooth operation.
  3. Zero Setting: Close the jaws completely. The dial indicator needle should point exactly to '0'. If it does not, loosen the bezel clamp screw and rotate the bezel until the '0' mark aligns with the needle. Tighten the clamp screw.
  4. Check Movement: Slide the movable jaw along the beam to ensure smooth, consistent movement without any binding or excessive play.

Operating Instructions

Always ensure the caliper is clean and the zero point is set correctly before taking any measurements.

Taking Measurements:

  • Outside Measurement: Place the object between the outside jaws. Gently close the jaws until they make firm contact with the object. Use the thumb roller for fine adjustment and the locking screw to secure the measurement. Read the main scale (millimeters) and then the dial indicator for the fractional part (hundredths of a millimeter).
  • Inside Measurement: Use the upper, smaller jaws to measure inside dimensions. Insert the jaws into the opening and expand them until they make firm contact with the inner surfaces. Read the measurement as described above.
  • Depth Measurement: Place the end of the main beam on the top surface of the feature to be measured. Extend the depth rod until it touches the bottom of the feature. Read the measurement.
  • Step Measurement: Use the step measuring faces (the ends of the main beam and the movable jaw) to measure steps or shoulders. Place the fixed jaw's step face on the higher surface and extend the movable jaw's step face to the lower surface. Read the measurement.

Maintenance

  • Cleaning: After each use, wipe the caliper clean with a dry, lint-free cloth to remove any dust, debris, or fingerprints. For stubborn grime, use a mild cleaning solution and immediately dry thoroughly.
  • Lubrication: Periodically apply a thin film of light machine oil (e.g., instrument oil) to the sliding surfaces of the beam and the rack gear to ensure smooth operation and prevent corrosion. Avoid over-lubrication, which can attract dust.
  • Storage: Store the caliper in its original protective case when not in use. Keep it in a dry, temperature-controlled environment, away from direct sunlight, moisture, and corrosive substances. Ensure the jaws are slightly open to prevent stress on the measuring faces.
  • Handling: Avoid dropping or subjecting the caliper to impact, as this can damage the precision components and affect accuracy.

Troubleshooting

  • Inaccurate Readings:
    • Check zero setting: Ensure the dial is zeroed correctly when jaws are closed.
    • Clean measuring surfaces: Dust or debris on the jaws can lead to errors.
    • Check for damage: Inspect jaws and beam for nicks or wear.
  • Sticky or Rough Movement:
    • Clean and lubricate: The beam and rack gear may need cleaning and a light application of instrument oil.
    • Check for debris: Ensure no foreign particles are lodged in the rack or sliding mechanism.
  • Dial Needle Not Returning to Zero:
    • Re-zero: Follow the zero-setting procedure.
    • Internal issue: If re-zeroing doesn't work, the internal mechanism might be damaged or require professional service.

User Tips

  • Always handle the caliper with care to maintain its precision.
  • Before taking a critical measurement, perform a quick zero check to ensure accuracy.
  • When measuring, apply consistent, light pressure to avoid deforming the workpiece or the caliper jaws.
  • For best results, take multiple measurements and average them, especially for critical dimensions.

Warranty and Support

Mitutoyo products are known for their high quality and reliability. For specific warranty information, please refer to the documentation included with your product or contact Mitutoyo customer support directly. Keep your Certificate of Inspection (as shown in Figure 4) as proof of authenticity and for reference.

For technical assistance, spare parts, or repair services, please contact your authorized Mitutoyo dealer or visit the official Mitutoyo website.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.