Honeywell T6861 Series

Contents

Honeywell T6861 Series Digital Thermostat User Manual

For FCU Air Conditioner Remote Temperature Control

1. Introduction

This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of your Honeywell T6861 Series Digital Thermostat. This non-programmable thermostat is designed for use with Fan Coil Unit (FCU) air conditioning systems, offering precise temperature control and energy-saving features. Please read this manual thoroughly before installation and use.

Available Models:

  • T6861V2WG (Vertical, Green display, 220VAC)
  • T6861V1WG (Vertical, Green display, 110VAC)
  • T6861V2WB (Vertical, Blue display, 220VAC)
  • T6861V1WB (Vertical, Blue display, 110VAC)
  • T6861H2WG (Horizontal, Green display, 220VAC)
  • T6861H1WG (Horizontal, Green display, 110VAC)
  • T6861H2WB (Horizontal, Blue display, 220VAC)
  • T6861H1WB (Horizontal, Blue display, 110VAC)

2. Safety Information

CAUTION: ELECTRICAL HAZARD

Improper installation can cause electrical shock or equipment damage. Always disconnect power before installation. Installation must be performed by a trained and experienced service technician.

3. Setup and Installation

The T6861 Series thermostat is designed for easy installation into an 86mm standard electrical box. It consists of a display unit and a separate wiring terminal block.

3.1 Package Contents

Verify that your package contains the following items:

  • Digital Thermostat Display Unit
  • Wiring Terminal Block
  • Mounting Screws
  • Installation Guide (PDF available online: User manual (PDF))
Package contents of the Honeywell T6861 thermostat, including the display unit, wiring block, screws, and installation guide.
Figure 1: Thermostat Package Contents

3.2 Wiring Instructions

The thermostat connects to your FCU system via a dedicated wiring terminal block. Ensure all power is disconnected before proceeding with wiring.

Back view of the Honeywell T6861 thermostat connected to its wiring terminal block, showing labeled terminals for system connections.
Figure 2: Thermostat Wiring Terminal Block

The wiring terminal block features numbered terminals (1-12) and specific function labels. Refer to the detailed wiring diagram in the official PDF manual for your specific FCU system configuration. Common terminals include:

  • N: Neutral
  • L: Live
  • Y: Cooling Output
  • Cc: Common for Cooling
  • W: Heating Output
  • Ch: Common for Heating
  • Gl, Gm, Gh: Fan Speed Outputs (Low, Medium, High)
  • Rs, RSb, Sc: Remote Sensor connections (if applicable)

After wiring the terminal block, connect the display unit to the terminal block using the provided harness. Secure the assembly to the wall using the mounting screws.

Thermostat display unit with its wiring harness connected to the back, ready for attachment to the mounted terminal block.
Figure 3: Display Unit Connection

4. Operating Instructions

Your T6861 thermostat features a large LCD display and intuitive buttons for easy control.

Four different display variations of the Honeywell T6861 thermostat, showing green and blue backlights, various room and set temperatures, and fan/mode settings.
Figure 4: Thermostat Display Options (Green and Blue Backlight)

4.1 Buttons and Display

The thermostat typically includes the following buttons:

  • Power Button: Turns the thermostat On/Off.
  • Mode Button: Cycles through operating modes (Heat, Cool, Auto, Vent).
  • Fan Button: Adjusts fan speed (Low, Med, High, Auto).
  • Up/Down Buttons: Adjusts temperature settings and other values.

The display shows current room temperature, set temperature, fan speed, operating mode, and occupancy status.

4.2 Mode Setting

Press the Mode button to select your desired operating mode:

  • Heat: Controls the heating system.
  • Cool: Controls the cooling system.
  • Auto: Automatically switches between heating and cooling based on the indoor temperature.
  • Vent: Only controls the ventilating device (fan).
Close-up of the thermostat display in Heat mode, showing 'Set to 23', 'Room 24.5 °C', 'Mode Heat', and 'Occupied'.
Figure 5: Thermostat in Heat Mode
Close-up of the thermostat display in Cool mode, showing 'Set to 23.5', 'Room 25.5 °C', 'Mode Cool', and 'Occupied'.
Figure 6: Thermostat in Cool Mode

4.3 Fan Setting

Press the Fan button to cycle through fan speeds:

  • Low: The fan runs at low speed.
  • Med: The fan runs at medium speed.
  • High: The fan runs at high speed.
  • Auto: The fan runs only when the heating or cooling system is active, and the fan speed depends on the difference between the room temperature and setting temperature.
Thermostat display showing 'High' fan speed, 'Room 25.0 °C', and 'Cool on'.
Figure 7: Thermostat with High Fan Speed

4.4 Temperature Setting

In Heat or Cool mode, use the Up or Down buttons to select your desired temperature. The 'Set to' value will flash while adjusting.

4.5 Energy Saving Mode

The thermostat can enter Energy Saving mode with fixed heat and cool setting temperatures. To activate/deactivate, press and hold the Mode button for 3 seconds (if configured as button control). When in Energy Saving mode, the 'Occupied' icon may change to 'Unoccupied'.

4.6 Time On and Time Off

Press and hold the Power button for more than 3 seconds to enter time setting mode. Use the Up or Down buttons to adjust the time value. Press the Power button again to restore to the previous mode. This feature is typically used for scheduled operation.

5. Maintenance

To ensure optimal performance and longevity of your thermostat, follow these simple maintenance guidelines:

  • Cleaning: Wipe the thermostat's surface with a soft, damp cloth. Do not use abrasive cleaners, solvents, or chemical sprays, as these can damage the display or casing.
  • Avoid Obstructions: Ensure that the thermostat is not covered by curtains, furniture, or other objects that could obstruct airflow or sensor readings.
  • Power Cycle: If the thermostat becomes unresponsive, try turning it off and then on again using the power button.

6. Troubleshooting Tips

If you encounter issues with your thermostat, refer to the table below for common problems and solutions:

If...Then...
Heating system does not turn on.
  • Set the mode to Heat by pressing the Mode button.
  • Check that the heat temperature setting is set above the room temperature and "Heat On" shows solidly in the display.
  • Wait five minutes for the heating system to respond.
Cooling system does not turn on.
  • Set the mode to Cool by pressing the Mode button.
  • Check that the cool temperature setting is set below the room temperature and "Cool On" shows solidly in the display.
  • Wait five minutes for the cooling system to respond.
The fan doesn't work.
  • Check whether the Fan mode is set to Auto.
  • Check whether the heating or cooling system works.
The Mode button doesn't work.
  • Check whether the keypad is locked or not.
  • Check whether the system is working in Energy Saving mode.
  • Check whether the thermostat is off.
The Fan button doesn't work.
  • Check whether the system is working in Energy Saving mode.
  • Check whether the thermostat is off.
The Up or Down button doesn't work.
  • Check whether the keypad is locked or not.
  • Check whether the system is working in Energy Saving mode.
  • Check whether the thermostat is off.

7. Specifications

FeatureDescription
Product TypeDigital Thermostat, Non-programmable
Model SeriesT6861 Series
BrandHoneywell (PROHEAT)
Power Supply110VAC/220VAC, 50/60Hz
Fan Speeds3 (Low, Medium, High) + Auto
DisplayBig LCD Display (Green or Blue backlight)
Temperature Units°C or °F (selectable)
InstallationEasy to install, fits 86mm standard box
FeaturesRemote Sensor capability, Energy Saving mode
Smart DeviceNo
CertificationCE
OriginMainland China
Package Dimensions10cm (L) x 10cm (W) x 10cm (H)
Package Weight0.35 kg
Diagram illustrating the Honeywell T6861 thermostat controlling a Fan Coil Unit (FCU) system, showing the air pipe, coil, fan, and valve connections.
Figure 8: T6861 for FCU System Overview
Key features of the T6861 thermostat including Big LCD Display, Easy to Install, Remote Sensor, °C or °F Choice, and Energy Saving Mode.
Figure 9: Key Features

8. Warranty and Support

For any technical assistance, warranty claims, or further inquiries, please contact the seller or manufacturer directly. The official user manual in PDF format can be downloaded here.

9. User Tips

  • Users have reported excellent and reliable performance, indicating a robust and functional design.
  • Ensure correct wiring for 110V or 220V systems as per your model to avoid damage.
  • Familiarize yourself with the Mode and Fan buttons to efficiently switch between heating, cooling, and fan speeds.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.