1. Introduction
Thank you for choosing the KeysLand FEKER IK84 Wireless Mechanical Keyboard DIY Kit. This kit allows you to build a personalized 84-key mechanical keyboard with triple-mode connectivity (Wired USB-C, 2.4Ghz Wireless, Bluetooth 5.0), hot-swappable switch sockets, and vibrant RGB backlighting. This manual provides detailed instructions for assembly, operation, and maintenance to ensure optimal performance and longevity of your keyboard.
2. Package Contents
Please inspect the package contents carefully. If any items are missing or damaged, contact your retailer.
- 1 x Keyboard Customized Kit (Case, PCB, Mute Cotton, Stabilizer, Steel Positioning Board, Battery)
- 1 x Type-C USB Cable (1.8m)
- 1 x 2.4G Receiver
- 1 x Keycap Puller
- 1 x Switches Puller
- 1 x User Manual

Image: All components included in the FEKER IK84 Keyboard DIY Kit package.
3. Setup and Assembly
The FEKER IK84 is a hot-swappable keyboard kit, allowing you to install switches without soldering. Follow these steps to assemble your keyboard:
- Prepare the PCB: The kit includes the PCB (Printed Circuit Board) with hot-swappable sockets, mute cotton, stabilizers, and a steel positioning board already assembled within the case.
- Install Switches: Align the pins of your chosen 3-pin or 5-pin mechanical switches with the hot-swappable sockets on the PCB. Gently push each switch into place until it clicks securely. Ensure the pins are straight to avoid bending.

Image: The keyboard PCB with hot-swappable sockets ready for switch installation.

Image: A close-up view of the hot-swappable switch sockets on the PCB.
- Install Keycaps: Once all switches are installed, carefully press your desired keycaps onto the switch stems. Use the provided keycap puller if you need to remove or adjust keycaps.

Image: The assembled PCB with switches installed, demonstrating the RGB lighting capabilities.
3.1 Connection Modes
The FEKER IK84 supports three connection modes:
- Wired (USB-C): Connect the provided Type-C USB cable to the keyboard's port and to an available USB port on your computer. The keyboard will automatically switch to wired mode and begin charging.
- 2.4Ghz Wireless: Insert the 2.4G receiver into a USB port on your computer. Locate the mode switch on the keyboard (usually on the back or side) and set it to the 2.4Ghz position. The keyboard should connect automatically.
- Bluetooth 5.0: Locate the mode switch on the keyboard and set it to the Bluetooth position. On your device (computer, tablet, phone), enable Bluetooth and search for new devices. Select "FEKER IK84" (or similar) from the list to pair. The keyboard supports Bluetooth 5.0 for stable and efficient wireless connection.

Image: Visual representation of the three available connection modes for the keyboard.
4. Operating Instructions
4.1 Basic Keyboard Functions
The IK84 functions as a standard 84-key keyboard. All keys perform their labeled functions. For specific secondary functions (e.g., F-keys, media controls), refer to the keycap legends or the included quick start guide.
4.2 RGB Backlight Control
The keyboard features 16.8 million color RGB backlighting with 18 different effects. Specific key combinations (often involving the 'Fn' key) are used to cycle through lighting modes, adjust brightness, and change colors. Refer to the quick start guide for exact key combinations.
4.3 Macro Programming
The FEKER IK84 supports macro programming and key re-assignment through a dedicated driver program. This software allows you to customize key functions and create complex macros for enhanced productivity or gaming. Please visit the official FEKER website or contact customer support to download the latest driver software.
5. Maintenance
5.1 Cleaning
- General Cleaning: Use a soft, dry cloth to wipe down the keyboard case. For dust and debris between keycaps, use compressed air.
- Keycap Cleaning: Keycaps can be removed using the provided keycap puller and cleaned with mild soap and water. Ensure they are completely dry before reattaching.
- Switch Cleaning: If switches feel gritty, you may carefully remove them with the switch puller and clean around the stem with a small brush or compressed air.
5.2 Battery Care
The keyboard is equipped with a built-in 6000mAh rechargeable Li-ion battery. To prolong battery life:
- Avoid completely draining the battery frequently.
- Charge the keyboard using the provided Type-C cable connected to a standard USB power source (DC 5V, 500mA Max).
- If storing the keyboard for an extended period, charge it to approximately 50% to 80% before storage.
6. Troubleshooting
- Keyboard not connecting:
- Ensure the correct connection mode (Wired, 2.4G, Bluetooth) is selected on the keyboard.
- For wired mode, check the USB-C cable connection.
- For 2.4G wireless, ensure the receiver is securely plugged into a USB port.
- For Bluetooth, ensure Bluetooth is enabled on your device and the keyboard is paired. Try re-pairing if necessary.
- Keys not responding:
- Check if the switches are fully seated in their hot-swappable sockets. Gently press down on the affected switch.
- If a specific switch is faulty, use the switch puller to remove it and replace it with a new one.
- RGB backlight not working or incorrect:
- Ensure the keyboard is powered on and charged.
- Use the designated key combinations to cycle through RGB modes and adjust brightness.
- If using custom settings, check the driver software.
- Battery not charging or holding charge:
- Verify the Type-C cable is properly connected to both the keyboard and a working USB power source.
- Try a different USB port or charging adapter.
- If the issue persists, the battery may need service.
7. Specifications
| Feature | Specification |
|---|---|
| Brand | FEKER |
| Layout | 80% layout, 84 Keys |
| Case Material | Frosted ABS Case |
| Color | Black |
| Mute Cotton | Yes |
| Switch Compatibility | 3/5pin adjustable, Hot-swappable (Cherry MX, Kailh, Gateron compatible) |
| Connection Modes | Triple Mode: USB Wired, Bluetooth LE 5.0, 2.4Ghz Wireless |
| Compatibility | Windows 7/8/10, Mac, Linux, iOS, Android |
| Backlight | 16.8 Million RGB, 18 effects, SMD Lamp Beads |
| Anti-Ghosting | NKRO (N-Key Rollover) |
| Battery | Built-in 6000mAh (3000mAh+3000mAh) Rechargeable Li-ion Battery |
| USB Operating Current | DC 5V, 500mA Max |
| Cable | Detachable 1.8m Type-C USB Cable |
| Chipset | 32 Bit MCU + 8M Flash on-board memory, 3 independent 256*256*256 RGB color management chips |
| Package Dimensions (L x W x H) | 35cm x 18cm x 5cm |
| Package Weight | 0.75 kg |
8. User Tips
- Test Switches Before Full Assembly: Before installing all keycaps, it's a good practice to connect the PCB to your computer and test each switch to ensure it's functioning correctly and properly seated.
- Careful Switch Removal: When using the switch puller, apply even pressure and pull straight up to avoid damaging the switch housing or the PCB socket.
- Experiment with Keycaps: The hot-swappable nature allows you to easily change keycaps. Explore different profiles and materials to find what suits your typing style best.
- Driver Software for Customization: Don't forget to download and utilize the driver software for advanced customization of key bindings, macros, and RGB lighting effects.
9. Warranty and Support
For warranty information, technical support, or any inquiries regarding your FEKER IK84 keyboard kit, please refer to the seller's policies or contact KeysLand Store customer service directly. Keep your purchase receipt as proof of purchase.