AISET NGE-5000 Series

Contents

AISET NGE-5000 Series Temperature Module User Manual

Models: NGE-5000, NGE-5411V-1, NGE-5411-1, NGE-5401-1, NGE-5441-1 K, NGE-5421-1, NGE-5401V-1

1. Product Overview

The AISET NGE-5000 series is a range of high-precision temperature control modules designed for various industrial and electrical applications. These modules feature a clear digital display for process value (PV) and set value (SV), along with intuitive controls for easy operation.

Front panel of the AISET NGE-5000 series temperature module
Front panel of the AISET NGE-5000 series temperature module, showing PV and SV displays, AT, OUT, ALM indicators, and control buttons.

1.1 Key Features

  • Digital display for Process Value (PV) and Set Value (SV)
  • Indicators for Auto-tuning (AT), Output (OUT), and Alarm (ALM)
  • User-friendly control buttons
  • High accuracy for precise temperature control
  • Compact design for easy integration

2. Specifications

ParameterDescription
Model NumberNGE-5000, NGE-5411V-1, NGE-5411-1, etc.
DIY SuppliesElectrical
OriginMainland China
Temperature Range0-400°C (K type thermocouple)
Accuracy0.5 level
Power Supply100-240VAC / 50Hz, 5VA
Dimensions (W x H x D)72mm x 72mm x 68mm
Package WeightApprox. 0.3 kg
Package Dimensions (L x W x H)10cm x 8cm x 8cm
Dimensional drawing of the NGE-5411-1 temperature module
Dimensional drawing of the NGE-5411-1 temperature module, showing 72mm width, 72mm height, and 68mm depth.
Side view of NGE-5411-1 with product label
Side view of the NGE-5411-1 temperature module with a product label detailing specifications.

3. Setup and Installation

3.1 Mounting

The NGE-5000 series module is designed for panel mounting. Ensure adequate space for ventilation and wiring connections. Refer to the dimensional drawing in Section 2 for precise cutout and mounting dimensions.

3.2 Wiring Connections

WARNING: Ensure all power is disconnected before performing any wiring to prevent electric shock or damage to the device.

Refer to the wiring diagram below for proper connections. Use appropriate gauge wires for power and output connections.

Rear view of NGE-5411-1 showing wiring terminals
Rear view of the NGE-5411-1 temperature module showing the wiring terminals.
  1. Power Supply (100-240VAC): Connect the main power supply to terminals 1 and 2.
  2. Output (OUT): Connect your controlled device (e.g., heater, relay) to terminals 3 and 4.
  3. Thermocouple Input (TC): Connect your K-type thermocouple to terminals 5 and 6. Ensure correct polarity (+ to + and - to -) for accurate readings.
  4. Alarm Output (ALM): If using the alarm function, connect your alarm device to terminals 8 and 9.

4. Operating Instructions

4.1 Front Panel Controls and Indicators

  • PV Display (Red): Shows the current Process Value (measured temperature).
  • SV Display (Green): Shows the Set Value (target temperature).
  • AT Indicator: Illuminates when the auto-tuning function is active.
  • OUT Indicator: Illuminates when the control output is active.
  • ALM Indicator: Illuminates when an alarm condition is met.
  • Power/Set Button (⌛): Used to power on/off (if applicable) and to enter/exit parameter setting modes.
  • Down Button (⌄): Used to decrease values or navigate menus.
  • Up Button (⌃): Used to increase values or navigate menus.

4.2 Setting the Target Temperature (SV)

  1. Press the Power/Set button briefly to enter the SV setting mode. The SV display will flash.
  2. Use the Up (⌃) and Down (⌄) buttons to adjust the Set Value to your desired temperature.
  3. Press the Power/Set button again to confirm the setting and exit the SV setting mode.

4.3 Auto-Tuning (AT)

Auto-tuning helps the controller optimize its PID parameters for stable temperature control. Consult the full product manual for detailed auto-tuning procedures, as this may vary slightly between specific NGE-5000 models.

5. Maintenance

The AISET NGE-5000 series temperature module is designed for reliable operation with minimal maintenance. Follow these guidelines:

  • Cleaning: Keep the front panel clean and free from dust. Use a soft, dry cloth for cleaning. Do not use abrasive cleaners or solvents.
  • Environmental Conditions: Ensure the module operates within its specified environmental conditions (temperature, humidity) to prevent damage.
  • Connections: Periodically check all wiring connections to ensure they are secure and free from corrosion.
  • Calibration: If temperature readings appear inaccurate, professional calibration may be required.

6. Troubleshooting

ProblemPossible CauseSolution
No display/Power offNo power supply or incorrect wiring.Check power connections (terminals 1-2) and ensure power is supplied.
Inaccurate temperature readingIncorrect thermocouple type, faulty thermocouple, or incorrect wiring polarity.Verify thermocouple type (K-type), check thermocouple for damage, ensure correct polarity at terminals 5-6.
Output not activatingSV not reached, OUT indicator off, or faulty output wiring.Check if PV has reached SV. Verify OUT indicator. Inspect wiring to controlled device (terminals 3-4).
ALM indicator always on/offAlarm parameters incorrectly set or faulty alarm wiring.Review alarm settings. Check wiring to alarm device (terminals 8-9).

7. User Tips

  • Always ensure the correct thermocouple type (K-type) is used with this module for accurate temperature measurement.
  • For optimal control performance, consider performing an auto-tune cycle after initial installation or if the controlled process changes significantly.
  • Keep the module away from strong electromagnetic interference to prevent erratic readings.

8. Warranty and Support

For warranty information and technical support, please refer to the documentation provided with your purchase or contact your supplier. Keep your purchase records for warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.