Introduction
Thank you for choosing the JONSBO TG-360 ARGB CPU Liquid Cooler. This all-in-one (AIO) liquid cooling system is designed to provide efficient heat dissipation for your CPU while offering customizable ARGB lighting effects. This manual will guide you through the installation, operation, maintenance, and troubleshooting of your new cooler.
Figure 1: JONSBO TG-360 CPU Liquid Cooler Overview
Setup and Installation
Before installation, ensure your system is powered off and unplugged. Refer to your motherboard manual for specific CPU socket mounting instructions if needed.
Package Contents
Figure 2: Included Mounting Hardware
Supported CPU Sockets
The JONSBO TG-360 supports a wide range of Intel and AMD sockets:
- **Intel:** LGA 1150, LGA 1155, LGA 1151, LGA1200, LGA 1700, LGA 2011
- **AMD:** AM4, Socket AM5
Figure 3: CPU Socket Compatibility
Installation Steps (General)
- Prepare CPU and Motherboard: Clean the CPU surface thoroughly. Apply thermal paste (included) to the center of the CPU in a pea-sized dot or thin line. The cooler features a slightly convex copper bottom for optimal contact.
- Install Mounting Brackets: Attach the appropriate mounting brackets for your CPU socket to the pump head.
- Mount Radiator and Fans: Secure the radiator to an available mounting location in your PC case (e.g., top, front, or rear). Ensure fans are oriented for optimal airflow (typically exhausting air out of the case when mounted at the top/rear, or intaking air when mounted at the front).
- Install Pump Head: Carefully place the pump head onto the CPU, aligning it with the mounting holes. Secure it with the provided screws, tightening them in a cross pattern until snug.
- Connect Cables:
- Fan Connection: The cold exhaust fan connects to the motherboard with a single cable for simplified wire management. Connect the 4-pin PWM fan connector to an available CPU_FAN or SYS_FAN header on your motherboard.
- Pump Connection: Connect the pump's 3-pin power connector to a dedicated AIO_PUMP or PUMP_FAN header on your motherboard.
- ARGB Lighting: Connect the 5V 3-pin ARGB connector from the cooler to a compatible 5V 3-pin ARGB header on your motherboard. This allows for synchronized lighting effects. Do NOT connect to a 12V RGB header.
- Adjust Pump Logo: The pump head features a damping rotation nameplate, allowing you to adjust the JONSBO logo direction for optimal aesthetic alignment after installation.
Figure 4: ARGB Connection Diagram
Figure 5: Rotatable Pump Logo
Figure 6: Simplified Fan Wiring
Operating Instructions
Power On
Once installation is complete, power on your computer. The fans and pump should start operating, and the ARGB lighting will illuminate.
ARGB Lighting Control
The JONSBO TG-360 features ARGB Phantom Synchronous Light Effect. This means the customizable lighting can be synchronized with your motherboard's ARGB software (e.g., ASUS Aura Sync, MSI Mystic Light Sync, GIGABYTE RGB Fusion, ASRock Polychrome Sync). Ensure the 5V 3-pin ARGB cable is correctly connected to your motherboard's ARGB header.
Figure 7: Motherboard ARGB Software Interface Example
Fan Speed Control
The fans are PWM controlled, allowing your motherboard to dynamically adjust their speed based on CPU temperature. This ensures optimal cooling performance and reduced noise levels when the system is under light load.
Video 1: JONSBO TG-240/360 ARGB Water/Liquid Cooler in action, showcasing RGB lighting and features.
Maintenance
Regular maintenance helps ensure the longevity and optimal performance of your liquid cooler.
- Dust Cleaning: Periodically clean the radiator fins and fan blades to prevent dust buildup, which can impede airflow and reduce cooling efficiency. Use compressed air or a soft brush.
- Check Tubing and Connections: While the cooler features a compression multilayer sealing interface for strong sealing and no leakage, it's good practice to occasionally inspect the tubing and connections for any signs of wear or damage.
- Fan Lifespan: The fans are designed for a long lifespan of ≥40,000 hours at 25°C.
Troubleshooting
No Power/Fans Not Spinning
- Ensure all power cables (4-pin PWM for fans, 3-pin for pump) are securely connected to the correct headers on your motherboard.
- Check your motherboard's BIOS/UEFI settings to ensure fan headers are enabled and configured correctly.
ARGB Lighting Not Working/Synchronizing
- Verify that the 5V 3-pin ARGB connector is securely plugged into a compatible 5V 3-pin ARGB header on your motherboard.
- Do NOT connect to a 12V RGB header, as this can damage the LEDs.
- Ensure your motherboard's ARGB software is installed and updated, and that the lighting effects are enabled and configured.
- If using a separate ARGB controller, ensure it is powered and correctly connected.
Poor Cooling Performance
- Check if the pump is running (you might hear a faint hum or feel vibrations). If not, refer to 'No Power/Fans Not Spinning'.
- Ensure the pump head is making good contact with the CPU. Re-seat if necessary, reapplying thermal paste.
- Verify that the fans are spinning and oriented correctly for optimal airflow.
- Clean any dust buildup from the radiator fins and fan blades.
- Check CPU temperatures using monitoring software to confirm the issue.
Specifications
Figure 8: Detailed Product Parameters
| Feature | Specification |
|---|---|
| Model Number | TG-360 |
| Type | CPU All In One Liquid Cooler |
| Radiator Size | 397mm (L) x 120mm (W) x 27mm (H) |
| Fan Size | 120mm x 120mm x 25mm (each) |
| Fan Speed | 900-1800 RPM (±10%) |
| Air Volume | 29.22-66.19 CFM (each) |
| Fan Noise | 22.9-35.4 dB(A) (max) |
| Fan Bearing | Hydraulic |
| Fan Interface | 4-pin PWM |
| Pump Size | 74mm x 89.2mm x 51.8mm |
| Pump Speed | 2500 RPM (±10%) |
| Pump Noise | < 30 dB(A) |
| Pump Voltage | 12V DC |
| Pump Power | 3.6W |
| RGB Support | A-RGB (5V 3-pin) |
| Heatsink Material | Copper & Aluminum |
| Supported CPU | LGA 1150, LGA 1155, LGA 1151, LGA1200, AM4, LGA 1700, Socket AM5, LGA 2011 |
| Certification | CE, RoHS |
User Tips
- Cable Management: Take advantage of the simplified fan wiring (single cable per fan) to achieve a cleaner build. Plan your cable routes before securing components.
- ARGB Customization: Experiment with your motherboard's ARGB software to find your preferred lighting patterns and colors. The 5V 3-pin ARGB allows for addressable effects.
- Pump Orientation: The rotatable pump logo is a thoughtful design feature. Don't forget to adjust it to match your build's aesthetic after the pump is mounted.
- Thermal Paste Application: While the cooler comes with thermal paste, ensure it's applied evenly and adequately for the best heat transfer.
Warranty and Support
For warranty claims or technical support, please contact your retailer or the official JONSBO customer service. Keep your proof of purchase for any warranty-related inquiries.
