1. Introduction
This remote control module is specifically designed for the VSETT 10+ electric scooter. Its primary function is to allow users to switch the scooter's maximum speed between a limited 25km/h mode (often required by local regulations) and the scooter's full, real power capability. This provides flexibility for riders to comply with speed limits when necessary and unleash the scooter's full potential in appropriate environments.
2. Package Contents
Please verify that all items listed below are included in your package:
- 1x Remote Control Module
- 1x Remote Controller
Figure 2.1: Remote Control Module and Remote Controller
3. Safety Information
Please read and understand all safety warnings before installation and use.
- General Safety: Installation and adjustment of this item require high hands-on ability and electrical knowledge. If you do not possess such skills, please seek assistance from a professional mechanic.
- Packaging Warning: To avoid danger of suffocation, keep the plastic packaging bag away from babies and children. Do not use this bag in cribs, beds, carriages, or playpens. This bag is not a toy.
- Model Compatibility: This module is ONLY compatible with VSETT 10+ electric scooters. Attempting to install it on other models may result in damage to the scooter or the module, and is not covered by any liability.
- Speed Regulations: Be aware of and comply with local laws and regulations regarding electric scooter speed limits. Use the full power mode responsibly and only where permitted.
4. Compatibility
This remote control module is designed exclusively for the VSETT 10+ electric scooter. It is crucial to verify your scooter model before attempting installation.
Important Notes:
- Some older VSETT 10+ models may not have a pre-existing socket for the speed-limit cable. In such cases, you may need to create a socket yourself or cut off the corresponding socket of the remote control module and connect the cables directly.
- If your scooter model does not have a speed-limit cable at all, this module cannot be installed.
- This module is NOT compatible with other scooter models such as Zero10X, Wispeed Suvpilot 150, Dualtron VICTOR, IO Hawk Legacy 2.0, TOURSOR X14 72V 10000W, Kukirn G2 pro/max, Vsett 10 Apex, or Vsett 10 Light.
5. Installation
Installation of the remote control module requires careful attention to wiring. Please refer to the diagrams and video below for guidance. It is highly recommended to have a professional perform the installation if you are not confident in your electrical knowledge.
5.1. Wiring Diagram
Figure 5.1: Remote Control Module Wiring Overview
Figure 5.2: Detailed DC Converter and Controller Connections
5.2. Installation Video Guide
Video 5.1: Step-by-step installation and operation demonstration for the speed control module on a VSETT 10+ scooter.
6. Operation
Once the remote control module is correctly installed, you can easily switch between speed modes using the provided remote controller.
- Power On: Turn on your VSETT 10+ electric scooter and ensure it is set to 3 gears.
- Verify Limited Speed: Test the scooter to confirm that the maximum speed is currently limited to 25km/h.
- Switch to Full Power: Press the button on the remote controller once. The scooter's display should show the maximum speed rising to 80+ km/h, indicating full power mode is active.
- Switch back to Limited Speed: Press the button on the remote controller again. The scooter's display should revert to 25km/h, indicating the speed limit is re-engaged.
Figure 6.1: Remote Controller in Use
7. Troubleshooting
If you encounter issues with your remote control module, consider the following:
- No Speed Change: Double-check all wiring connections according to the installation diagrams. Ensure the module is receiving power and the remote controller has a working battery.
- Incorrect Speed Display: Verify that your scooter is a VSETT 10+ model. This module is not compatible with other models, and incorrect installation on an unsupported model will not yield expected results.
- Remote Not Responding: Ensure the remote controller is within range of the receiving antenna and there are no obstructions. Check the remote's battery.
For complex issues or if you are unsure about any step, it is strongly recommended to consult a professional electric scooter mechanic.
8. Specifications
| Feature | Detail |
|---|---|
| Brand Name | MACURY |
| Model Number | VSETT 10+ |
| Function | Remote speed limit switching (25km/h to full power) |
| Origin | Mainland China |
| Package Length | 15 cm |
| Package Width | 10 cm |
| Package Height | 10 cm |
| Package Weight | 0.3 kg |
9. User Tips
- Professional Installation: Due to the electrical nature of this modification, if you lack experience with scooter electronics, it is highly recommended to have the module installed by a qualified professional.
- Wiring for Older Models: Be prepared that some older VSETT 10+ models might require you to modify the speed-limit cable (e.g., adding a socket or direct wiring) if it doesn't match the module's connectors.
- Verify Functionality: Always test the speed switching functionality in a safe, controlled environment after installation to ensure it operates as expected before riding.
- Stay Informed: Keep up-to-date with your local electric scooter regulations, as speed limits can vary and change.
10. Warranty & Support
For any questions regarding product functionality, troubleshooting, or warranty claims, please contact the seller directly through your purchase platform. They can provide specific assistance related to your product.
A user manual in PDF format may also be available for further reference. Please check the product page or contact the seller for a direct link to the PDF document: User Manual (PDF)