1. Introduction
This manual provides essential information for the safe and effective installation, operation, and maintenance of the GEYA GRD9L Automatic Reclosing Device. The GRD9L is designed to be combined with GEYA GYL9 RCCB/ELCB circuit breakers to provide automatic reclosing functionality in case of unwanted tripping after an electrical fault, such as an earth leakage current.
The GEYA GRD9L series offers various control modes to suit different application requirements, ensuring reliable electrical system management.
2. Safety Information
WARNING: Electrical installation and maintenance should only be performed by qualified personnel. Failure to follow these instructions may result in serious injury or death.
- Always disconnect power before installing or servicing the device.
- Ensure all wiring connections are secure and comply with local electrical codes.
- Do not operate the device if it appears damaged.
- Verify correct voltage and current ratings before installation.
- The device is designed for specific applications; do not use it for purposes other than those specified.
3. Product Overview
The GEYA GRD9L is an automatic reclosing device designed to restore power after a circuit breaker trip caused by an electrical fault. It is intended for use in conjunction with GEYA GYL9 series Residual Current Circuit Breakers (RCCB) or Earth Leakage Circuit Breakers (ELCB).
3.1. Control Modes
The GRD9L series offers several control modes, each tailored for different operational needs:
- GRD9L-C (Switch Input Control Mode): Controlled via an external switch input (e.g., a relay). Available in DC12V, DC24-48V, and AC220V versions.
- GRD9L-D (Switch Input + Auto Reclosing Control Mode): Combines external switch control with automatic reclosing functionality. Available in DC12V, DC24-48V, and AC220V versions.
- GRD9L-S (RS485 Control Mode): Designed for remote control and monitoring via RS485 communication (e.g., with a computer or PLC). Available in DC12V, DC24-48V, and AC220V versions.
- GRD9L-R (Auto Reclose Control Mode): Fully automatic reclosing with configurable reclose times (e.g., 10s, 60s, 300s). Available in DC12V, DC24-48V, and AC220V versions. This is a top-selling model.

4. Specifications
| Attribute | Value |
|---|---|
| Brand Name | GEYA |
| Model Number | GYL9 RCCB Recloser |
| Product Name | RCCB ELCB Recloser Part |
| Type | Earth Leakage, RCD |
| Rated Voltage | 220V (AC) |
| Recloser Voltage Range | DC12V OR AC220V OR DC24-48V |
| Control Mode | Switch input or RS485 or Autoclose |
| Is Smart Device | No |
| is_customized | Yes |
| Certification | CE |
| Origin | Mainland China |
| Package Weight | 0.25 kg |
| Package Dimensions (L x W x H) | 12cm x 10cm x 5cm |
4.1. Dimensions

5. Installation and Setup
The GEYA GRD9L is designed for easy integration with GEYA GYL9 series RCCB/ELCBs. Follow these steps for proper installation:
5.1. General Installation

- Cooperate with RCCB:
- Align the GRD9L recloser with the GYL9 RCCB.
- Slide the recloser onto the RCCB, ensuring a secure mechanical and electrical connection.
- Fasten any retaining clips or screws as indicated.
- Cooperate with MCB:
- Align the GRD9L recloser with the MCB.
- Slide the recloser onto the MCB, ensuring a secure mechanical and electrical connection.
- Fasten any retaining clips or screws as indicated.
- Accessories Installing:
Ensure all necessary accessories are correctly installed to facilitate proper operation and control.
- Closing Lock:
The device features a closing lock function. When checking the circuit, the RCCB/MCB cannot close if the lock function is activated. This is a safety feature to prevent accidental reclosing during inspection or maintenance.
5.2. Wiring Diagram (GRD9L-R Example)

Refer to Figure 4 for the wiring diagram of the GRD9L-R model. Ensure correct connections for PWR (Power), AUX (Auxiliary), and control terminals (A1, A2, COM, NC) based on your specific model and application. The AUX terminals provide a MAX100mA output.
6. Operating Instructions
The operation of the GRD9L depends on the selected control mode:
6.1. Manual/Auto Mode Selection
Most GRD9L models feature an AUTO/MANU (Manual) switch and a LOCK mechanism. Refer to Figure 4 for visual guidance.
- AUTO Mode: The device will automatically attempt to reclose the connected RCCB/ELCB after a trip, according to its programmed reclosing sequence and times.
- MANU Mode: The device will not automatically reclose. Reclosing must be initiated manually.
- LOCK: This mechanism prevents the RCCB/MCB from closing, providing a safety lockout during maintenance.
6.2. Control Mode Specifics
- GRD9L-C (Switch Input Control): The recloser operates based on an external switch signal. When the switch is activated, the recloser will attempt to close the circuit.
- GRD9L-D (Switch Input + Auto Reclosing): This mode allows for both external switch control and automatic reclosing. The automatic reclosing sequence will activate if a trip occurs, but manual intervention via the switch input is also possible.
- GRD9L-S (RS485 Control): This model is controlled remotely via an RS485 communication interface. Commands sent from a computer or PLC can initiate closing, opening, or query the device status.
- GRD9L-R (Auto Reclose Control): This is a fully automatic reclosing device. After a trip, it will attempt to reclose the circuit at predefined intervals. Common reclose times include 10 seconds, 60 seconds, and 300 seconds. The device will typically attempt reclosing multiple times before locking out if the fault persists.
6.3. Test Function (GRD9L-R Example)

Some GRD9L-R models include a "Test Monthly" button (Figure 5). Pressing this button simulates a trip to verify the reclosing function. It is recommended to perform this test monthly to ensure proper operation.
7. Maintenance
- Regular Inspection: Periodically inspect the device for any signs of physical damage, loose connections, or overheating.
- Cleaning: Keep the device clean and free from dust and debris. Use a dry, soft cloth for cleaning. Do not use solvents or abrasive cleaners.
- Functional Testing: For models with a "Test" button, perform functional tests as recommended (e.g., monthly) to ensure the reclosing mechanism is working correctly.
- Power Disconnection: Always disconnect power to the circuit before performing any maintenance or inspection.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Device does not reclose automatically. |
|
|
| RCCB/MCB cannot be closed manually. |
|
|
| RS485 communication not working (GRD9L-S). |
|
|
9. User Tips
- Model Selection: When ordering, carefully specify the exact model (e.g., GRD9L-S-DC24-48V) to ensure compatibility with your system's voltage and control requirements.
- Replacement Use: This device is ideal for replacing existing recloser control parts or upgrading GYL9 RCCB/ELCBs with automatic reclosing capabilities.
- DC Voltage Compatibility: The recloser motor can operate with DC12V, DC24-48V, or AC220V depending on the model. Always confirm the voltage range of your specific unit.
- Application Suitability: The GRD9L is particularly suitable for applications requiring automated control of electricity flow and quick restoration after transient faults.
10. Warranty and Support
GEYA products are certified to required industry standards, including CE. For specific warranty details, technical support, or service inquiries, please contact GEYA Official Store or your local distributor. Ensure you retain your purchase records for warranty claims.
