Estardyn 0.96 inch OLED module

Contents

Estardyn 0.96 Inch OLED Display Module

User Manual

Model: 0.96 inch OLED module | Brand: Estardyn

1. Introduction

This manual provides detailed instructions for the Estardyn 0.96 Inch OLED Display Module, available with SSD1306 or SSD1315 driver ICs. This compact, high-resolution (128x64 pixels) display is designed for integration with various microcontrollers, including Arduino, 51 Series, MSP430 Series, STM32/2, and CSR ICs. It features ultra-low power consumption and adjustable brightness/contrast, making it ideal for a wide range of embedded projects.

Front view of the 0.96 inch OLED display module showing White and Blue&Yellow color variants.
Figure 1: Estardyn 0.96 Inch OLED Display Module (White and Blue&Yellow variants)

2. Specifications

The Estardyn 0.96 Inch OLED Display Module offers robust performance in a compact form factor. Key specifications are detailed below:

FeatureSpecification
Display Mode128*64 Graphic
Resolution128 x 64 pixels
Driver ICSSD1306 (Blue board), SSD1315 (Black board)
Interface TypeIIC (I2C)
Pins4 pins (GND, VCC, SCL, SDA)
Operating Voltage3V ~ 5V DC
Power Consumption (Full Screen)0.08W
Working Temperature-30 °C to 70 °C
Drive Duty1/64 Duty
Panel Dimensions (approx)26.70 x 19.26 x 1.85 mm (1.03 x 0.76 x 0.07 inch)
Active Area (approx)21.74 x 11.2 mm (0.86 x 0.44 inch)
CustomizationYes
Comparison of SSD1306 and SSD1315 OLED modules, highlighting different driver ICs and their respective dimensions.
Figure 2: Comparison of SSD1306 (left) and SSD1315 (right) module dimensions and active areas.

3. Setup Instructions

Follow these steps to properly set up your OLED display module:

  1. Pin Connection: The module uses a 4-pin IIC interface. Connect the pins as follows:
    • GND: Ground connection.
    • VCC: Power supply (3V to 5V DC).
    • SCL: Serial Clock Line for IIC communication.
    • SDA: Serial Data Line for IIC communication.
    Detailed front view of the OLED module with pin labels (GND, VCC, SCL, SDA).
    Figure 3: OLED Module Pinout
  2. IIC Address Selection: The module typically supports two IIC addresses, 0x78 and 0x7A, which can be selected using jumpers on the back of the board. Refer to the images below for the location of these jumpers. Ensure the correct address is configured for your project.
    • SSD1306 (Blue Board): Address selection jumpers are labeled 'IIC ADRESS SELECT'.
    • SSD1315 (Black Board): Address selection jumpers are labeled 'R11 R12'.
    Rear view of the blue PCB OLED module (SSD1306) showing IIC address selection jumpers (0x78, 0x7A).
    Figure 4: SSD1306 IIC Address Selection
    Rear view of the black PCB OLED module (SSD1315) showing IIC address selection jumpers (0x78, 0x7A).
    Figure 5: SSD1315 IIC Address Selection
  3. Microcontroller Compatibility: The module is fully compatible with a wide range of microcontrollers. Ensure your chosen microcontroller supports IIC communication and has appropriate libraries for the SSD1306 or SSD1315 driver IC.
  4. Power Supply: Provide a stable DC voltage between 3V and 5V to the VCC pin.

4. Operating Instructions

Once the module is correctly wired to your microcontroller, you can begin programming it to display information.

  1. Software Libraries: Utilize appropriate libraries for your microcontroller and the specific driver IC (SSD1306 or SSD1315). For Arduino, popular libraries like Adafruit SSD1306 are widely available and provide functions for text, graphics, and image display.
  2. Initialization: In your code, initialize the OLED display by specifying its IIC address and resolution.
  3. Displaying Content: Use the library functions to draw pixels, lines, shapes, text, and even bitmaps on the display. The 128x64 resolution allows for clear and detailed visuals.
  4. Brightness and Contrast: The module supports adjustable brightness and contrast. Refer to your chosen library's documentation for functions to control these parameters, allowing you to optimize visibility for different environments.
  5. Power Efficiency: Take advantage of the ultra-low power consumption by turning off the display or reducing brightness when not actively needed, especially in battery-powered applications.
Multiple display colors (Blue&Yellow, Blue, White) on the OLED module.
Figure 6: Example display outputs in various colors.

5. Maintenance

The Estardyn OLED Display Module is a robust electronic component, but proper care ensures its longevity and optimal performance.

  • Handling: Always handle the module by its edges to avoid touching the display surface or the delicate flex cable.
  • Cleaning: If necessary, gently clean the display surface with a soft, lint-free cloth. Avoid using abrasive materials or harsh chemical cleaners.
  • Storage: Store the module in an anti-static bag in a dry, cool environment, away from direct sunlight and extreme temperatures.
  • Environmental Conditions: Operate the module within the specified working temperature range of -30 °C to 70 °C. Avoid exposure to excessive moisture or corrosive substances.

6. Troubleshooting

If you encounter issues with your OLED display module, consider the following troubleshooting steps:

  • No Display/Blank Screen:
    • Verify all pin connections (GND, VCC, SCL, SDA) are secure and correct.
    • Ensure the power supply voltage is within the 3V-5V DC range.
    • Check the IIC address selection jumpers on the back of the board. Confirm the address used in your code matches the hardware setting.
    • Confirm that the correct display library is installed and initialized in your code.
    • Test with a known working example code to rule out software issues.
  • Garbled or Incorrect Display:
    • Double-check the IIC address and ensure it matches your code.
    • Verify that the correct driver IC (SSD1306 or SSD1315) is specified in your software library initialization.
    • Ensure the display resolution (128x64) is correctly set in your code.
    • Check for any loose connections or shorts on the PCB.
  • Flickering Display:
    • Ensure a stable power supply. Fluctuations can cause flickering.
    • Check for proper grounding.
    • Reduce the IIC communication speed in your code if necessary.
  • Partial Display:
    • Confirm the active area and panel dimensions are consistent with your expectations.
    • Review your code for correct buffer management and display update commands.

7. User Tips

  • Library Selection: For Arduino users, the Adafruit SSD1306 library is highly recommended due to its comprehensive features and active community support.
  • IIC Scanner: If you're unsure of the module's IIC address, use an IIC scanner sketch (available online for Arduino) to detect the address automatically.
  • Power Considerations: While the module has low power consumption, ensure your microcontroller can supply sufficient current, especially if powering other components from the same source.
  • Code Examples: Start with simple 'Hello World' examples provided with libraries to confirm basic functionality before implementing complex graphics.

8. Warranty and Support

For any technical assistance, warranty claims, or further inquiries regarding your Estardyn 0.96 Inch OLED Display Module, please contact the seller directly through the platform where the purchase was made. Provide your order details and a clear description of the issue to facilitate prompt support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.