1. Introduction
This manual provides detailed instructions for the setup, operation, and maintenance of your Estardyn 12864 SPI LCD Module. This 128x64 dot matrix graphic display features an SPI interface and is driven by the ST7567A IC, offering a clear FSTN display for various embedded applications.

2. Features
- Display Resolution: 128x64 pixels
- Interface: SPI (Serial Peripheral Interface)
- Driver IC: ST7567A
- Display Type: FSTN (Film Compensated Super-Twisted Nematic)
- Display Technology: COG (Chip-On-Glass) Graphic Display
- Operating Temperature: -20°C to 70°C
- Storage Temperature: -30°C to 80°C
- Optional Variants: Available with or without a font library chip, and with or without a protective iron frame.


3. Specifications
| Parameter | Value |
|---|---|
| Display Type | FSTN |
| Driver IC | ST7567A |
| Operating Temperature | -20°C to 70°C |
| Storage Temperature | -30°C to 80°C |
| Interface | SPI |
| Dot Pitch | 0.3mm x 0.3mm |
| Dot Size | 0.28mm x 0.28mm |
| Resolution | 128 x 64 |
| Module Dimensions | 47.00mm x 34.60mm |
| Viewing Area | 42.42mm x 22.84mm |
| Active Area | 40.88mm x 21.76mm |
| Thickness (with frame) | 4.80mm |
| Thickness (panel only) | 1.34mm |

4. Package Contents
The standard package for the 12864 SPI LCD Module typically includes:
- 1x Estardyn 12864 SPI LCD Module
- 1x Set of Pin Headers (for connection)

5. Setup
Follow these steps to connect and prepare your 12864 SPI LCD Module:
5.1 Pin Description
Refer to the table below and Figure 4 for the pinout of the module:
| Pin No. | Label | Description |
|---|---|---|
| 1 | GND | Ground |
| 2 | VCC | Power Supply (typically 3.3V or 5V, check module specifications) |
| 3 | SCL | Serial Clock (SPI Clock) |
| 4 | SDA | Serial Data (SPI MOSI) |
| 5 | DC | Data/Command Selection |
| 6 | RST | Reset Pin |
| 7 | CS | Chip Select (SPI Slave Select) |
| 8 | BL | Backlight Control |
| 9 | CS-F | Chip Select for Font Library (if applicable) |
| 10 | OUT | Output (specific function may vary) |
5.2 Connection to Microcontroller
- Power Connection: Connect the GND pin to your microcontroller's ground and VCC to the appropriate power supply (e.g., 3.3V or 5V, depending on your module's requirements and microcontroller's logic level).
- SPI Connection: Connect SCL, SDA, DC, RST, and CS pins to the corresponding SPI and control pins on your microcontroller.
- Backlight: Connect the BL pin to a digital output pin on your microcontroller to control the backlight.
- Font Library Chip (if present): If your module includes a font library chip, connect the CS-F pin to an additional digital output pin on your microcontroller. This pin is used to select the font chip for character data.
6. Operating Instructions
To operate the 12864 SPI LCD Module, you will typically need to use a compatible library with your chosen microcontroller (e.g., Arduino, ESP32, Raspberry Pi).
6.1 Software Setup
- Install Libraries: Search for and install a graphics library compatible with the ST7567A driver IC. For Arduino, libraries like U8g2 or Adafruit GFX with a specific ST7567A driver are commonly used.
- Initialization: In your code, initialize the display object, specifying the correct SPI pins (SCL, SDA, DC, RST, CS) and the display resolution (128x64).
- Backlight Control: Set the BL pin to HIGH to turn on the backlight. You can use PWM on this pin for brightness control if supported by your microcontroller.
6.2 Displaying Graphics and Text
Once initialized, you can use the library functions to:
- Draw pixels, lines, rectangles, circles, and other shapes.
- Display text using built-in fonts or custom fonts. If your module has a font library chip, the library might provide functions to access its characters.
- Clear the display or update specific regions.

7. Maintenance
- Cleaning: Gently wipe the display surface with a soft, lint-free cloth. Avoid using harsh chemicals or abrasive materials.
- Handling: Handle the module by its edges to avoid touching the display area or damaging the delicate components on the PCB.
- Storage: Store the module in a dry, anti-static environment, away from direct sunlight and extreme temperatures, within the specified storage temperature range (-30°C to 80°C).
- Protection: If your module does not have a protective iron frame, take extra care to prevent physical damage to the display panel.
8. Troubleshooting
- No Display / Blank Screen:
- Check all power connections (VCC, GND) and ensure they are correct and stable.
- Verify that the backlight (BL pin) is enabled in your code or connected correctly.
- Double-check all SPI connections (SCL, SDA, DC, RST, CS) for continuity and correct pin assignments.
- Ensure your software library is correctly initialized for the ST7567A driver and 128x64 resolution.
- Confirm that the power supply voltage matches the module's requirements.
- Garbled or Incorrect Display:
- Ensure the correct SPI mode and clock speed are configured in your software.
- Verify that the data/command (DC) pin is toggling correctly according to the SPI protocol.
- Check for any loose connections or interference on the data lines.
- If using a font library chip, ensure the CS-F pin is correctly controlled.
- Display is too dim or too bright:
- Adjust the backlight control (BL pin) in your software. If using PWM, modify the duty cycle.
9. User Tips
- Arduino Compatibility: This module is known to work well with Arduino microcontrollers. Users have reported successful integration using libraries compatible with the UC1701 driver, which is similar to the ST7567A.
- Low Power: The module is designed for low power consumption, making it suitable for battery-powered projects.
- Library Selection: When searching for a library, prioritize those that explicitly support the ST7567A driver IC for optimal performance and compatibility.
10. Warranty and Support
For warranty information, technical support, or further assistance, please contact the seller or manufacturer directly. Keep your purchase records for any warranty claims.