Estardyn 12864-06D

Contents

Estardyn 12864-06D LCD Module User Manual

Model: 12864-06D (GMG12864-06D)

128x64 Dot Matrix LCD Module with SPI Interface

1. Introduction

This manual provides detailed instructions for the Estardyn 12864-06D LCD module. This is a compact 128x64 dot matrix display featuring a ST7565R driver IC and an SPI (Serial Peripheral Interface) for communication. It supports Simplified Chinese fonts and is designed for various embedded applications requiring a clear, monochrome graphical display.

Three Estardyn 12864 LCD modules with different backlight colors (black, blue, gray) displaying text 'ST7565 Display SPI interface STM32F030F4P6 CUBE MX HAL SPI1 Good seller!'
Figure 1: Estardyn 12864-06D LCD Modules (various screen colors)

2. Specifications

The following table outlines the key technical specifications of the Estardyn 12864-06D LCD module:

Feature Specification
Model Number 12864-06D (GMG12864-06D)
Display Mode 128*64 Dot Matrix
Resolution 128x64 pixels
Driver IC ST7565R
Font IC 20L16S1Y (Simplified Chinese)
Interface Mode SPI Interface
Operating Voltage 3.3V
Operating Temperature -20°C to +70°C
Storage Temperature -30°C to +80°C
Overall Dimensions 61.8 x 45.8 x 6.8 mm (L x W x H)
Window Size 58 x 28 mm
Display Type FSTN & Positive
Polarizer Mode Transflective
Viewing Direction 6 o'clock
Drive Method 1/9 Bias, 1/65 Duty
Connector COG (Chip-On-Glass)
Backlight Type LED (Side/White)
Technical drawing of the Estardyn GMG12864-06D LCD module, showing dimensions, pin assignments, and display specifications.
Figure 2: Technical Drawing with Dimensions and Pinout

3. Setup Instructions

Follow these steps to properly connect and set up your LCD module:

3.1 Pin Assignment

The module features a 13-pin header. Refer to Figure 2 for the physical layout and the table below for pin functions:

Pin No. Symbol Description
1 /CS Chip Select (Active Low)
2 RES Reset Pin (Active Low)
3 RS Register Select (Data/Command)
4 SCK Serial Clock Input
5 SI Serial Data Input
6 VSS Ground
7 VDD Power Supply (3.3V)
8 GND Ground
9 LEDA LED Anode (Backlight Power)
10 LEDK LED Cathode (Backlight Ground)
11 IC_CS Internal Chip Select (Connect to /CS)
12 IC_SCK Internal Serial Clock (Connect to SCK)
13 IC_SDI Internal Serial Data Input (Connect to SI)

3.2 Electrical Connections

  1. Connect VDD (Pin 7) to a stable 3.3V power supply.
  2. Connect VSS (Pin 6) and GND (Pin 8) to the system ground.
  3. Connect LEDA (Pin 9) to the positive backlight supply (typically 3.3V, possibly through a current-limiting resistor if required by your specific setup).
  4. Connect LEDK (Pin 10) to the backlight ground.
  5. Connect the SPI interface pins (/CS, RES, RS, SCK, SI) to the corresponding SPI pins on your microcontroller or development board. Ensure that IC_CS, IC_SCK, and IC_SDI are connected to /CS, SCK, and SI respectively.
  6. Verify all connections before applying power to prevent damage to the module or host device.
Rear view of the Estardyn GMG12864-06D LCD module PCB, showing components and pin connections.
Figure 3: Rear View of the LCD Module PCB

4. Operating Instructions

The Estardyn 12864-06D LCD module is controlled via an SPI interface using the ST7565R driver IC. Programming involves sending commands and data to the display controller to initialize the display, draw graphics, and display text.

4.1 Initialization

Before sending display data, the ST7565R controller must be initialized. This typically involves:

  • Resetting the display (pulling RES low then high).
  • Setting the display mode and contrast.
  • Turning on the display.

4.2 Data Transmission

Data (pixel information, characters) is sent via the SPI interface. The RS pin determines whether the transmitted byte is a command (RS low) or data (RS high). Consult the ST7565R datasheet for a complete list of commands and their functions.

4.3 Chinese Font Support

The module includes a 20L16S1Y font IC, providing built-in support for Simplified Chinese characters. Refer to the font IC's documentation for character encoding and display methods.

5. Maintenance

To ensure the longevity and optimal performance of your LCD module, follow these maintenance guidelines:

  • Cleaning: Use a soft, lint-free cloth, slightly dampened with water or a mild, non-abrasive cleaner, to gently wipe the display surface. Avoid harsh chemicals, solvents, or abrasive materials.
  • Handling: Avoid applying excessive pressure to the display surface, as this can damage the LCD panel. Handle the module by its edges.
  • Environment: Operate and store the module within the specified temperature and humidity ranges (-20°C to +70°C operating, -30°C to +80°C storage). Avoid direct sunlight and extreme temperature fluctuations.
  • Static Electricity: Take precautions against electrostatic discharge (ESD) when handling the module, as it can damage sensitive electronic components.

6. Troubleshooting

If you encounter issues with your LCD module, consider the following troubleshooting steps:

  • No Display/Blank Screen:
    • Check power connections (VDD, VSS, GND) to ensure the module is receiving the correct 3.3V supply.
    • Verify backlight connections (LEDA, LEDK) and ensure the backlight is powered.
    • Confirm that the RES pin is properly toggled (low then high) during initialization.
    • Ensure the display is turned on via software commands to the ST7565R controller.
  • Garbled or Incorrect Display:
    • Check all SPI data lines (SCK, SI, /CS, RS) for proper connection and signal integrity.
    • Review your initialization code for the ST7565R controller; incorrect settings can lead to display issues.
    • Ensure data is being sent correctly (command vs. data mode via RS pin).
    • Verify the data format and addressing used for sending pixel data.
  • Backlight Not Working:
    • Check LEDA and LEDK connections.
    • Measure voltage across LEDA and LEDK to ensure power is supplied to the backlight.

7. User Tips

  • Development Environment: For users working with STM32 microcontrollers, consider using STM32CubeMX for project setup and HAL (Hardware Abstraction Layer) libraries for SPI communication. This can simplify the development process.
  • Driver Libraries: Look for existing open-source libraries for the ST7565R driver IC, which can significantly reduce development time for display control.
  • Power Supply: Always ensure a stable 3.3V power supply. Fluctuations can lead to unstable display behavior or damage.

8. Warranty and Support

For any technical assistance, warranty inquiries, or support related to your Estardyn 12864-06D LCD module, please contact the Estardyn Flagship Store directly through the platform where the product was purchased. Provide your order details and a clear description of the issue for prompt support.

© 2024 Estardyn. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.