1. Product Overview
The LILYGO® TTGO T-Echo A7682E Shield Module is a SIM module expansion board designed to augment the capabilities of the T-Echo device. It integrates an A7682E SIM module, a microphone, and a speaker, providing enhanced communication features. This module is easy to install, requiring only the removal of the T-Echo's back cover and replacement with the shield.
The A7682E module supports 4G LTE CAT1/GSM/GPRS/EDGE network protocols, making it compatible with regions including Europe, Southeast Asia, and South America. It extends the T-Echo's multi-functional LoRa communication capabilities, which are built around the nRF52840 chip and feature an E-Paper screen, GPS positioning, NFC functionality, and various sensors. The device supports Arduino and nRF5-SDK development environments, making it an ideal platform for developing LoRa communication, IoT nodes, and low-power applications. It is compatible with open-source firmware projects like SoftRF and Meshtastic for decentralized communication networks.

2. Package Contents
Please verify that all items are present and in good condition upon opening the package:
- 1 x T-Echo A7682E Shield Module
- 1 x T-ECHO-A7682-PFC (Flexible Printed Circuit)
- 1 x 1.25mm male to male 80mm Same direction terminal line
- 1 x Small double-sided sticker

3. Setup and Installation
3.1 Hardware Installation
- Carefully remove the back cover of your existing T-Echo device.
- Align the T-Echo A7682E Shield Module with the connectors on the T-Echo main board.
- Gently press the shield module into place, ensuring all connectors are securely seated.
- Replace the back cover of the T-Echo device.


3.2 Pin Diagram
The following diagram illustrates the pinout and connections for the T-Echo A7682E Shield Module. For detailed pin definitions, please refer to the utilities.h file in the official repository.


3.3 Development Platforms
The T-Echo A7682E Shield Module supports various development environments:
- Arduino IDE: Supports Adafruit nRF52.
- PlatformIO: Cross-platform development environment.
- nRF5-SDK: Nordic official SDK.
Arduino IDE Setup:
- Download Arduino IDE.
- Open Preferences and add
https://www.adafruit.com/package_adafruit_index.jsonto the Board Manager URL list. - Open the Board Manager, wait for the index to update, select Adafruit nRF52 by Adafruit, and click Install.
- After installation, select Nordic nRF52840 (PCA10056) from the board list.
- Copy all folders in the
libdirectory to the Arduino library folder. - Open your sketch, select the correct port, then click Upload.
When using USB to download firmware, double-click the reset button to enter DFU mode.
PlatformIO Setup:
- Install Visual Studio Code and Python.
- Search for and install the PlatformIO IDE extension in VS Code.
- After restarting VS Code, click File → Open Folder → select the LilyGO-T-ECHO folder.
- Click the ✓ at the bottom to compile, then upload.
nRF5-SDK Setup:
- Download nRF5-SDK.
- Use nRF5-SDK for programming, supporting advanced features like NFC.
Note: NFC functionality is not supported in Adafruit_nRF52_Arduino. Use nRF5-SDK for NFC-related development.
4. Operating Instructions
4.1 DFU (Device Firmware Update) Mode
To enter DFU mode for firmware download via USB, double-click the reset button on the device.
4.2 LoRa Output Power Configuration
After setting the LoRa output power, current limit configuration is required. An example is shown below:
// Set output power to 22 dBm (range: -17 to 22 dBm)
radio.setOutputPower(22);
// Set over-current protection limit to 80 mA (range: 45-240 mA)
radio.setCurrentLimit(80);
// Setting to 0 disables over-current protection5. Specifications
| Feature | Specification |
|---|---|
| Model Number | T-Echo A7682 Shield Module |
| MCU | nRF52840 @ ARM Cortex-M4 |
| Flash | MX25R1635FZUIL0 or ZD25WQ16B (selected based on supply conditions) |
| RAM | 256kB |
| Wireless (BLE) | Bluetooth 5.0 |
| LoRa | SX1262, multiple frequency bands, -17 to 22 dBm output power |
| Display | E-Paper, low power (1.54 inch SPI E-Paper, 200x200 resolution, 2s full refresh) |
| GPS | Supported (L76K Multi-System Positioning GNSS module) |
| NFC | Supported (Near Field Communication) |
| Bus Interfaces | UART, SPI, TWI, PDM, I2S, QSPI |
| Dimensions (WxHxD) | 65mm x 15mm x 53mm |
| Package | Yes |

6. Troubleshooting (FAQ)
- Q: Does the FLASH model vary between boards?
- A: Yes, the FLASH will be selected as MX25R1635FZUILO or ZD25WQ16B based on supply conditions. Please pay attention to this distinction during use.
- Q: NFC is not working with Arduino?
- A: NFC functionality is not supported in Adafruit_nRF52_Arduino. Please use nRF5-SDK for NFC programming.
- Q: How do I enter DFU (download) mode?
- A: Double-click the reset button to enter DFU mode when using USB to download firmware.
- Q: What open-source firmware is compatible with T-Echo?
- A: T-Echo supports SoftRF (aircraft collision avoidance) and Meshtastic (LoRa mesh communication).
7. Warranty and Support
For additional documentation, detailed guides, and support, please refer to the official LILYGO® resources. A comprehensive user manual in PDF format is available:
For further assistance, please contact LILYGO® Official Store customer service.