Taidacent 4.2V 2A Magnetic Resonance Charging PCB

Contents

User Manual

Taidacent 4.2V 2A Magnetic Resonance Charging PCB Module

Model: 4.2V 2A Magnetic Resonance Charging PCB

Brand: Taidacent

1. Introduction

This manual provides detailed instructions for the safe and efficient use of the Taidacent 4.2V 2A Magnetic Resonance Charging PCB Module. This module is designed for high-power resonant wireless charging applications, suitable for wireless power banks and similar devices. It utilizes the XKT001 transmitter chip and XKT-R05 receiver chip for reliable performance and long-term operation without significant temperature rise.

Taidacent Wireless Charging Module (Transmitter and Receiver)
Figure 1: Taidacent Wireless Charging Module (Transmitter and Receiver)

2. Safety Information

  • Always ensure proper polarity when connecting power to avoid damage to the module and connected devices.
  • Do not exceed the specified input voltage (5V for transmitter) or output current (2A for receiver) to prevent overheating or component failure.
  • Maintain the recommended transceiver distance of 2-10mm. Operating outside this range, especially at distances greater than 2mm with high receiving voltage, can damage the Schottky diode on the receiver.
  • This module is intended for switching output and direct battery charging; it is not designed for regulated output.
  • Keep the module away from water, moisture, and extreme temperatures.
  • Handle the PCB with care to avoid electrostatic discharge (ESD) damage.

3. Product Overview

3.1 Components

The module consists of a transmitter board with a transmitting coil and a receiver board with a receiving coil, designed for magnetic resonance wireless power transfer.

  • Transmitter Board: Integrates the XKT001 high-voltage wireless transmitter chip.
  • Transmitting Coil: Copper coil for generating the magnetic field.
  • Receiver Board: Integrates the XKT-R05 receiving technology chip, designed for long-term operation without significant temperature rise.
  • Receiving Coil: Copper coil for capturing the magnetic field and inducing current.

3.2 Specifications

ParameterValue
Emitter Voltage5V
Transmitter Module Size (L x W x T)16mm x 12mm x 4mm
Transmitting Coil (Outer Diameter)45mm
Transmitting Coil (Inner Diameter)30mm
Transmitting Coil Inductance3uH
Maximum Emission Current5V 2.6A
Receiving Battery Charging Board Size (L x W x T)25mm x 18mm x 3mm
Receiving Coil (Outer Diameter)45mm
Receiving Coil (Inner Diameter)30mm
Receiving Coil Inductance3uH
Receiving Maximum Output4.2V 2A
Transceiver Distance2mm ~ 10mm
Accessory TypeCharger Accessories
OriginMainland China

4. Setup Instructions

Follow these steps to set up your Taidacent wireless charging module:

  1. Identify Components: Separate the transmitter board with its coil and the receiver board with its coil.
  2. Connect Transmitter: Connect the 5V power supply to the transmitter board. Ensure correct polarity: red wire for positive (+), black wire for negative (-). The maximum emission current is 5V 2.6A.
  3. Connect Receiver: Connect the receiver board's output wires to the battery you intend to charge. The receiver provides a maximum output of 4.2V 2A. Ensure correct polarity for battery charging.
  4. Position Coils: Place the transmitting coil and receiving coil facing each other. The optimal transceiver distance is between 2mm and 10mm.
  5. Power On: Apply power to the transmitter. The receiver should begin charging the connected battery.
Wiring Diagram and Component Details for Transmitter and Receiver Modules
Figure 2: Wiring Diagram and Component Details for Transmitter and Receiver Modules. Note the 5V 2.6A transmitter board input and 4.2V 2A receiver output.

Important Note on Distance:

This module is designed for a normal working distance of 2mm. If the use distance is greater than 2mm, and the receiving voltage becomes too high, it can damage the Schottky diode on the receiver board. Always monitor the receiving voltage, especially at larger distances within the 2-10mm range.

5. Operating Instructions

Once the module is set up as described in Section 4:

  1. Ensure both the transmitter and receiver coils are aligned and within the 2-10mm operating distance.
  2. Apply 5V power to the transmitter module.
  3. The receiver module will automatically begin to output 4.2V at up to 2A to charge the connected battery.
  4. Monitor the charging process. The XKT-R05 chip is designed for long-term work without significant temperature rise, but it's always good practice to observe for any unusual heat.
  5. To stop charging, simply remove power from the transmitter or separate the coils beyond the operating distance.
Wireless Charging Module Test Setup with Power Supplies and Measurement Devices
Figure 3: Example of a test setup demonstrating the module's operation with power supplies and measurement equipment.

6. Maintenance

The Taidacent wireless charging module is designed for durability and requires minimal maintenance. However, following these guidelines can prolong its lifespan:

  • Keep the module clean and free from dust and debris. Use a soft, dry cloth for cleaning.
  • Avoid physical impact or bending of the PCB and coils.
  • Ensure proper ventilation around the module during operation to prevent heat buildup.
  • Regularly inspect wiring for any signs of wear or damage.

7. Troubleshooting

If you encounter issues with your wireless charging module, consider the following:

  • No Power Output:
    • Check if the 5V power supply is correctly connected to the transmitter and is providing power.
    • Verify the polarity of all connections.
    • Ensure the transmitting and receiving coils are properly aligned and within the 2-10mm operating distance.
    • Inspect for any visible damage to the PCB or coils.
  • Overheating:
    • Ensure the input voltage does not exceed 5V and the output current does not exceed 2A.
    • Verify the transceiver distance is within the recommended range (2-10mm). Operating too far or too close might cause inefficiencies and heat.
    • Ensure adequate ventilation.
  • Damaged Schottky Diode:
    • This can occur if the receiving voltage is too high, especially when operating at distances greater than 2mm. Always adhere to the recommended operating distance and monitor voltage.

8. User Tips

  • For optimal performance, try to keep the coils as close as possible within the recommended 2-10mm range, while ensuring the receiving voltage does not become excessively high.
  • When integrating into a project, consider enclosing the coils in non-metallic materials to maintain efficient power transfer.
  • Always double-check wiring before applying power to prevent accidental damage.

9. Warranty and Support

This product is manufactured under strict quality control standards. For any technical support or warranty inquiries, please contact your retailer or the manufacturer directly. Please retain your proof of purchase for warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.