1. General Introduction
The XTOOL smart diagnostic system (referred to as the "Scan Tool") is an advanced scanning tool based on the Android operating system. It supports multiple languages and is suitable for different countries and regions. The advantage of this OBD-II (On-Board Diagnostics version 2) scanner is its comprehensive functions and its ability to quickly provide the user with more accurate diagnostic information.
The D9S PRO is designed for mechanics, electricians, and automotive repair stores. It features FCA AutoAuth Function, Full-System Automotive Diagnostics, Live Data, Bi-directional Control test, ECU Coding and ECU Programming, 45+ Common Special Functions, Intelligent Topology Mapping, Refresh Hidden Functions, IMMO & Key Programming, and 3 Years Software Updates. With 98% vehicle coverage and compatibility with over 100 brands and 10,000 car models, the XTOOL D9SPRO Bluetooth Diagnostic Tool is a versatile and reliable tool for any automotive professional.
Main Units
The Smart Diagnostic System main units include:
- Tablet: P902
- Wireless Diagnostic Module: V207 VCI (Vehicle communication interface) box
- Other accessories

Figure 1: XTOOL D9S PRO Main Unit and Components
2. Safety Information and Operation Instructions
Please read this user manual carefully before using the Smart Diagnostic System. When reading the manual, please pay attention to the words "Note" or "Caution", and read them carefully for appropriate operation.
Operation Instructions
For safe operation, please follow the instructions below:
- Keep the device away from heat or fumes when in use.
- If the vehicle battery contains acid, please keep your hands and skin or fire sources away from the battery during testing.
- The exhaust gas of the vehicle contains harmful chemicals. Please ensure adequate ventilation.
- Do not touch the vehicle cooling system components or exhaust manifolds when the engine is running due to the high temperatures reached.
- Make sure the car is securely parked, Neutral is selected or the selector is at the P or N position to prevent the vehicle from moving when the engine starts.
- Make sure the (DLC) Diagnostic Link Connector is functioning properly before starting the test to avoid damage to the Diagnostic Computer.
- Do not switch off the power or unplug the connectors during testing. Doing so may damage the ECU (Electronic Control Unit) and/or the Diagnostic Computer.
CAUTIONS!
- Avoid shaking, dropping or dismantling the scan tool as it may damage the internal components.
- Use only your fingertips to touch the LCD screen. Hard or sharp objects may damage the scan tool.
- Do not use excessive force.
- Do not expose the screen to strong sunlight for a long period.
- Please keep the scan tool away from water and moisture.
- Store and use the scan tool only within the temperature ranges identified in the Technical Specifications section.
- Keep the unit away from strong magnetic fields.
3. Setup
Connecting Power
The scan tool may need to be charged before first use. Confirm the proper power adapter (either 120 VAC North American or 240 VAC European version) is attached to the AC/DC charger.
Plug the AC/DC charger into a wall outlet and charge the scan tool by the AC/DC power supply port.
Note: A fully discharged battery will take approximately 6 hours to fully charge. The scan tool can be used while charging.
Activation
After first-time users press and hold the power button to turn on the system, the system will automatically enter the guided process and request the user to select the language for the operating system.

Figure 2: Language Selection
After setting the system language, click Next to enter the Wi-Fi connection page.

Figure 3: Wi-Fi Connection
Select a network to connect to on the Wi-Fi connection page. You need to enter the Wi-Fi password to establish Wi-Fi connectivity and the activation page. You can also click the "Trial" button in the upper right corner to try it out before activation. However, activation is highly recommended to take advantage of any new online software updates.

Figure 4: Activation Screen
Click Start Activation to enter the activation page.

Figure 5: Email Input for Activation
A pop-up window showing Activation Success indicates that you have completed the first boot setup. Please input your email address as requested.

Figure 6: Activation Success
Click OK to enter the diagnostic system and start using the device.
Main Unit Components (Tablet)
- 9.7-inch touch screen
- Type-C Port
- Power Button - Long press to turn off/on the tablet, short press to enter sleeping mode
- Rear Camera
- Nameplate
- Holder
- Speaker
VCI Box
The VCI (Vehicle Communication Interface) box is used for wireless communication with the vehicle.
- DB15 Port
- Display with vehicle voltage
- Type-B Port
- Reset button - Long press to reset the VCI box

Figure 7: VCI Box Overview
OBD2-16 Adapter
This adapter connects to the vehicle's DLC (Diagnostic Link Connector) port.
- OBD Male Connector – Plugs into vehicle's DLC port
- DB15 port – Connects to main cable

Figure 8: OBD2-16 Adapter
DB15 Main Cable
This cable connects the OBD2-16 adapter to the VCI box and provides power input.
- DB15 Port – Connects to OBD2-16 Adapter
- DB15 Port – Connects to VCI
- 12V DC Power Input Port

Figure 9: DB15 Main Cable
Vehicle Connection
The scan tool must be connected to the vehicle's OBD-II port so that the tablet can establish correct vehicle communication. Please perform the following steps:
- Turn on the tablet.
- Connect VCI with Vehicle via main test cable and OBD adapter, make sure WIFI connection works fine.
- Switch on the ignition and tap on the Diagnostic application to start your diagnosis.

Figure 10: Wireless Vehicle Connection
Note: The vehicle's DLC is not always located under the dash; for the location of the DLC, please refer to the vehicle owner's manual. Some older vehicles are not compatible with the OBD II-16 adapter, please make sure you're using the correct adapter.
Wired Connection
When using functions such as ECU programming & coding, please use the USB 3.0 to TYPE-B main cable to connect the tablet to the VCI box to prevent the failure of function execution due to unstable data transmission and thus any other damage.
For models with DoIP protocol communication, please be sure the device is connected to vehicle by wire.
For Self-Test
The self-test is mainly used to detect whether there is a fault in the internal hardware of the device. When performing the self-test function, please do not connect the VCI box or tablet directly to the vehicle, otherwise irreversible damage may be caused to your vehicle!
- Plug the power cord into the 12V DC port of the VCI box.
- Enter the following path: Main Menu >> Setting >> Self-test, make sure the device is not connected to any vehicle, click OK to perform self-test function.

Figure 11: Self-Test Procedure
4. Operating the Diagnostic Tool
Beginning Diagnostic Testing
After the tablet device is properly connected to the vehicle, you can start the vehicle diagnosis.
Vehicle Selection
The scan tool supports the following 3 ways to access the smart diagnostics system:
- AUTO SCAN
- MANUAL INPUT
- SELECT VEHICLE BY AREA

Figure 12: Vehicle Selection Menu
Click the VIN button in the upper left corner and then choose to enter the vehicle diagnosis through either AUTO SCAN or MANUAL INPUT.
AUTO SCAN: It supports the automatic reading of vehicle VIN code. You can also tap on the button "AUTO SCAN" on the diagnosis system entrance to use this function. Please make sure that the car and the device are well connected before using this function.
If your model is not recognized, please try the following steps:
- UPDATE all software, and check whether the APP is updated in [Settings].
- Please click Diagnosis on the main menu to enter the selection menu, manually select the engine system to read the ECU information, and confirm whether the VIN can be read.
- Contact the XTOOL technical team to provide the VIN code to confirm whether the model supports automatic identification of VIN.
MANUAL ENTER: It supports manual input of car VIN code. When entering the VIN code manually, make sure that the 17 characters entered are correct to ensure accurate test results.
In addition to the above 3 methods, you can also choose a car brand by selecting the appropriate region at the top of the screen. You can select the vehicle model that needs to be diagnosed according to the area.
OBD-II supports reading the related fault codes of the Powertrain Control Module (PCM).
DEMO: A demonstration program. Click this button to experience and learn the operation processes of the diagnostic function.
Some models provide multiple entry methods in the sub-menu, including:
- Automatic Detection
- Manual Selection
- System Selection

Figure 13: Diagnostic Entry Methods
Automatic Detection will automatically identify the vehicle's VIN code, and then read the information of your target diagnostic object. If you choose "Manual selection", then you can continue to select the vehicle brand, year, and model of the vehicle in the sub-menu to diagnose the vehicle. Enter "System Selection", you can also diagnose the vehicle according to the system according to your needs after selecting the model.
Diagnosis Functions
Diagnostics functions supported by the scan tool are listed below:
- Read ECU Information
- Read/Clear Trouble Code
- Read Live Data
- Actuation Test (Bi-Directional Control)

Figure 14: Diagnostic Functions Menu
Read ECU Information
This function is to read ECU version information and is the equivalent of "System Identification" or "System Information" in some electronic control systems. These equivalent terms all refer to reading ECU-related software and hardware versions, models and production date of diesel engines, part numbers, etc. This information is helpful when recording maintenance records and ordering new parts.

Figure 15: ECU Information
Read Trouble Code
In the process of diagnosis, if the device shows "System is OK" or "No Trouble Code", it means there is no related trouble code stored in ECU or some troubles are not under the control of ECU. Most troubles are mechanical system troubles or executive circuit troubles. It is also possible that the signal of a sensor may be inaccurate but within limits, which can be examined using Live Data.

Figure 16: DTCs Report
Clear Trouble Code
It allows for clearing current and historical trouble codes stored in the ECU memory, under the premise that all the troubles have been resolved.
Some troubles are immediately detected by the ECU with the key in the run position and without the engine running. Other troubles are not detected until very specific test conditions are met such as engine coolant temperature within a range, speed within a range for a duration of time, throttle percentage within a range, etc.
If the trouble codes are erased when the trouble remains unresolved, the trouble code will reappear in the ECU the next time the ECU performs the specific diagnostic test for that trouble.
If the trouble is resolved but there is a stored trouble code, sometimes the ECU will detect the resolution and clear the trouble code or more likely, classify it as "historical" trouble.
If the trouble is resolved and the user clears the trouble codes, the trouble history will be cleared.
If the user intends to have another colleague or mechanic investigate the problem, it is not recommended for the user to clear the trouble code since doing so may erase information helpful to others who may investigate the issue.
Read Live Data
Real-time information about various sensors is called "Live Data". Live Data includes parameter identifications (PIDs) of the running engine such as oil pressure, temperature, engine speed, fuel oil temperature, coolant temperature, intake air temperature, etc. Based on these parameters, we can predict directly where the problem lies, which helps to narrow the scope of maintenance. For some vehicles, during their actual operation, the problems such as performance characteristics or sensitivity reduction, can be evaluated using live data.
Note: The speed may vary depending on the speed of data sent from the vehicle and the number of data parameters being shown.

Figure 17: 8-in-1 Live Data Graphing
Click the magnifying glass on the top right, you can search for related PIDs based on keywords.
Custom: The scan tool includes support to select and show multiple PIDs. Click Display All to display all PIDs. This enables you to see relationships between data parameters.
Combine: The scan tool includes support to select multiple PIDs and click Combine to combine different graphs into one chart.
Data recording: The scan tool supports recording the current data values in the form of text. You can view the recorded files in Reports > Data Replay.
Pause: Click this button to pause the recording timeline. It freezes the data display, for closer examination and review.
Actuation Test (Bi-Directional Control)
Actuation test, also known as bidirectional control, is a generic term used to describe sending and receiving information between one device and another. This function is used mainly to judge whether these actuating components of the engine are working properly.
The vehicle engineers responsible for designing computer control systems programmed them so a scan tool could request information or command a module to perform specific tests and functions. Some manufacturers refer to bidirectional controls as functional tests, actuator tests, inspection tests, system tests or the like. Reinitialization and reprogramming also can be included in the list of bidirectional controls.
This function allows the device to send information to and receive information from, vehicle control modules. For example, in the case of OBD II generic information Mode 1 (which relates to data parameters), the scan tool user initiates a request for information from the powertrain control module (PCM), and the PCM responds by sending the information back to the scan tool for display. Most enhanced scan tools also can actuate relays, injectors and coils, perform system tests, etc. Users could check the individual part to see if it is working properly by actuation test.

Figure 18: Bi-Directional Control
XTOOL D9SPRO Car Diagnostic Tools is a full bi-directional control scan tool that can command car ECUs to perform various active tests like, Injector Tests, Fuel Injector Balance, Compression Test, Cooling Fan, A/C Clutch On/Off, ABS Motor Pump, Windows/ Wipers/Sunroof/Doors, to provide in-depth diagnostic tests and pinpoint fault causes like locating bad injector efficiently & accurately.
Note: Active Tests available vary across vehicles. Older vehicles tend to have fewer tests available.
ECU Coding & Programming
Since the introduction of OBD II and leading up to modern Hybrids and EVs, computers, and software in cars have been expanding at an exponential rate. In-car software is becoming one of the leading needs for service, and updating software may be the only way to fix some of these issues:
- Drivability
- Fuel Efficiency
- Power Loss
- Fault Codes
- Durability of Mechanical Parts
The Programming and Coding function is used to re-flash the vehicle control modules, which allows you to update the computer software of the vehicle to the latest version, as well as to reprogram adaptive data of certain components after making repairs or replacements.
There are two general types of programming operations:
- ECU Coding: Also known as Teach-in Program, or Component Adaptation, is used to reprogram adaptive data for electronic control modules after repairs or replacements of parts.
- ECU Programming: Updates ECU software to boost performance & enhance system stability.
*NOTE: Codable control modules/components are system-specific, which means that not all control modules are codable.

Figure 19: ECU Coding & Programming
XTOOL D9SPRO diagnostic scan tool can perform Online ECU Programming on BMW, Mercedes Benz, Volkswagen, Offline ECU Programming on Ford, Lincoln, Mazda and ECU Coding on Volkswagen, Audi, Skoda and etc to program/reflash ECUs, perform Online Calibrations, Online Parameterizations, and customize car settings.
Online ECU programming on ECM, PCM, BCM of specific BMW, Mercedes, VW, to: Replace the existing software, firmware in the ECU; program/reflash new modules after ECU replacement; Fix software-controlled driving performance and emission issues.
Offline ECU Programming on specific Ford, Lincoln and Mazda, to: Copy the codes from old module to the new one when you have swapped the ECU/Module from a donor car; Perform Programmable Module Installation (PMI) to reprogram the adaptive data for certain components after repairs or replacements.
ECU Coding is used to reflash the vehicle control modules, allowing you to reprogram adaptive data for certain components after making repairs or replacements. You can use the XTOOL D9SPRO to stimulate all the possibilities of the vehicles.
After replacing control units, bad actuators, or certain parts, coding is needed to make the replaced parts stored and recognized by the ECU. Almost all systems that include engine, fuel, injector, gear shift, ABS, airbag system, and so on can be coded with this scanner. Before coding, please read and record the original module’s information.
Including: Recode Changed Modules; Optimize Vehicle Performance; Re-Flash Hidden Functions; Renew ECUs Coordination; Reprogram; Adaptive Data; Improve Fuel Efficiency; Reduce Power Loss; Improve the Durability of Mechanical Parts, etc.
IMPORTANT: When reprogramming onboard, please always make sure the vehicle battery is fully charged and in good working condition to avoid operation failure caused by abnormal voltage. We recommend connecting an external battery maintainer to the vehicle to ensure a steady voltage is maintained throughout programming. The required voltage differs by the vehicle manufacturer. Consult vehicle manufacturer for correct voltage to be maintained.
Occasionally a flash update procedure may not complete properly. Common causes of flash errors include poor cable connections between the tablet, VCI, and vehicle, the vehicle ignition being switched off before the flash procedure is complete, or low vehicle battery voltage.
If the process quits, recheck all the cable connections to assure good communications and initialize the flash procedure. The programming procedure will automatically repeat if the previous operation does not succeed. Please use this feature with caution and it is not recommended for non-professionals.
Topology Mapping
XTOOL D9SPRO Car Diagnostic Scanner Topology Mapping provides a clear and intuitive panoramic view of the vehicle's electronic system, helping technicians quickly understand and analyze the vehicle's electronic system structure. Graphical module layout simplifies the inspection and maintenance process of complex systems, reducing manual operations and guesswork. When a fault occurs, the affected modules and their relationship to other systems can be quickly identified, thus speeding up fault diagnosis.
- Equipped with color coded module status for faster full system diagnostic results.
- View the communication structure between modules clearly with all the situation of each system.
- One click to display the fault code and enter the system executive function directly.

Figure 20: Full Systems Diagnostic with Topology Mapping
Note: Topology Map Compatibility For GM/CHRYSLER/JEEP/DODGE/FORD/TOYOTA/NISSAN/HONDA/BMW/BENZ/HYUNDAI/MAZDA (MORE COMING SOON). Not available for All Vehicle Makes. Please contact support for compatibility check.
Pre-Scan and Post-Scan
Experience unparalleled vehicle diagnostics with our upgraded Advanced Pre-Scan and Post-Scan features.
- PRE SCAN: Can read the vehicle’s current fault codes and stored historical fault codes. These fault codes will provide initial clues to potential problems in the vehicle's systems. Help technicians and car owners understand the current health status of the vehicle and provide guidance for repairs.
- POST SCAN: After repair or maintenance is completed, use the diagnostic equipment to scan the vehicle again to ensure that all fault codes have been cleared and the vehicle system is normal. Make sure all issues are resolved, the vehicle is in top condition after repairs, and avoid hidden problems.

Figure 21: Pre & Post Scan Function
IMMO & Key Programming
XTOOL D9SPRO Key Fob Programmer can disable a lost vehicle key and program the replacement key fob. One or more replacement key fobs can be programmed. This includes programming new key fobs, Read PIN code/pin code calculation, Check number of keys, Generate key, Add key, All key lost.
- Work with EEPROM Adapter
- Read/write/backup the IMMO data.
- Read PIN code
- Add New Keys (Fob/Smart)
- Remote Learning
- Key Matching
- Remote Learn
- ALL KEYS LOST Functions, etc.

Figure 22: IMMO & Key Programming
Note: Key programming does not work on all cars, please check the compatibility before purchase. It needs additional equipment for the keys.
FCA AutoAuth Access (NEW)
XTOOL D9SPRO Automotive Diagnostic Scanner supports access to the Security Gateway Module on 2018 and For Fiat/Chrysler/Dodge vehicles so that diagnostic tools can read code, clear code, bi-directional control (active test), etc. (No Need FCA 12+8 Cable).

Figure 23: FCA AutoAuth Access
Note: The buyer is required to register an FCA account; any charges have nothing to do with the seller.
CAN FD/DoIP Protocols
XTOOL D9SPRO Automotive Diagnostic Tool with CAN FD Protocol covers for GM MY2020+ models. No extra CAN FD adapter needed. With DoIP Protocol covers for BMW E/F/G Chassis/Jaguar/Land Rover vehicle makes. It can work on 88+ car brands, 140+ models and 10,000 cars globally, including 12V sedans, light duty trucks, SUVs, mini vans, hybrids. With software updates, the vehicle coverage grows continuously!
Diagnostic Report 2.0
The Upgraded Diagnostic Report 2.0 enables you to create comprehensive reports with four types, an icon display for main systems, and a customizable layout with your shop's logo. Enjoy categorizing and merging reports, adding client information, all while streamlining diagnostics to enhance customer satisfaction.

Figure 24: Diagnostic Report V2.0
5. Maintenance Functions (45+ Special Services)
The Scan Tool supports a lot of commonly used special reset functions, allowing you to quickly access your vehicle system for various scheduled services, maintenance, and reset performance. These functions often eliminate the need to reset codes after resolving common problems. Since XTOOL is continuously developing, this manual may not include all of the latest special functions that are available for download. This user manual lists some of the commonly used special reset services for your reference.

Figure 25: 45+ Maintenance Services
Note: Not all models are supported, please contact the seller to check compatibility before purchase!
ABS Bleeding
Anti-Lock Braking System keeps the tires from locking up immediately when there are brakes. Keeping ABS in good condition can give full play to the effectiveness of the brakes, shorten the braking time and distance, prevent the vehicle from skidding and tailing during emergency braking, ensure good driving stability and steering maneuverability, and avoid violent friction between the tires and the ground to reduce tire wear. When the ABS contains air, the ABS bleeding function must be performed to bleed the brake system to restore ABS brake sensitivity.
ABS Bleeding can be performed in the following cases:
- Replace the rear brake distributor pump or the front brake distributor pump.
- Severe brake fluid shortage.
- Change the brake fluid.
The operation guidelines of the ABS Bleeding function are shown as below:
- Read the operating instructions and precautions that appear on the screen carefully before performing the operation to ensure that the equipment and car are in the correct condition.
- Attach bleeder bottle to the left rear bleeder screw.
- Open the left rear bleeder screw.

Figure 26: ABS Bleeding Step 1
When ready, click "OK" to enter the bleed procedure, and pumping the brake pedal continuously with steady applies every 2 seconds during the entire procedure.

Figure 27: ABS Bleeding Step 2
Continue pumping the brake pedal; when air bubbles are no longer visible, select OK to enter the next bleed procedure for the left front wheel.
Repeat the operation 3 times to complete the bleed procedure for the left front wheel, right front wheel and right rear wheel in turn.
Stop pumping the brake pedal, and close the right rear bleeder screw.
Click OK to complete the entire bleed procedure.
Oil Reset
The scan tool can be used to reset the engine oil life system, which calculates the optimum oil life change interval based on the vehicle's driving conditions and climate. The oil life reminder must be reset each time the oil is changed so that the system can calculate when the next oil change is required.
This function can be performed in the following cases:
- If the service lamp is on, you must provide service for the car. After service, you need to reset the driving mileage or driving time so that the service lamp turns off and the system enables the new service cycle.
- After changing engine oil or electric appliances that monitor oil life, you need to reset the service lamp.
The operation guidelines of the Oil Reset function are shown as below:
- Enter the Oil Reset menu and choose relevant models according to the vehicle being tested.
- Follow the instructions displayed that are specific to the vehicle and press OK after completing the instructions shown.
- Enter Maintenance mileage reset menu.
- Click INPUT and enter a reasonable value of remaining oil life and press OK.
- Confirm the [New Value] you just entered, and then click OK at the bottom right to complete the procedure.
- Message of 'Write successfully' displays when Oil Reset function has successfully performed.
EPB (Electronic Parking Brake) Reset
Electronic Parking Brake (EPB) System reset is a popular special function. You can use this function to reset the electronic parking brake system and brake pads (retraction, release of the brake pump), G-sensor and body angle calibration. This function has multiple uses and can safely and effectively maintain the electronic brake system. These applications include deactivating and activating brake control systems, assisting in controlling brake fluid, applying and releasing brake pads, setting brakes after replacing brake discs or brake pads, etc.
- If the brake pad wears the brake pad sense line, the brake pad sense line will send a signal to the onboard tablet asking for replacing the brake pad. After replacing the brake pad, you must reset the brake pad to clear the trouble code. Otherwise, the car continues to falsely notify the user that the brake pads are in need of replacement.
- A reset must be performed in the following cases:
- The brake pad and brake pad wear sensor are replaced.
- The brake pad indicator lamp is on.
- The brake pad sensor circuit is shorted.
- The servo motor is replaced.
The operation guidelines of the EPB function are shown as below:
- Enter the EPB menu and choose relevant models according to the vehicle being tested.
- Follow the instructions displayed and press YES after completing the instructions shown.
- Enter the Enter maintenance mode menu and release the handbrake brake. And press OK after completing the instructions shown.
- Wait until the message of 'Successful operation' pops up. And press OK to exit the menu.
- Enter the Exit maintenance mode menu and wait until the message of "Successful operation" pops up.
SAS (Steering Angle Sensor) Adjustment
Steering Angle Sensors (SAS) System Calibration permanently stores the current steering wheel position as the straight-ahead position in the SAS EEPROM. Therefore, the front wheels and the steering wheel must be set exactly to the straight-ahead position before calibration. In addition, the VIN is also read from the instrument cluster and stored permanently in the SAS EEPROM. On successful completion of calibration, the SAS fault codes will be automatically cleared.
To reset the steering angle, you need to first find the relative zero point position for the car to drive in a straight line. Taking this position as a reference, the ECU can calculate the accurate angle for left and right steering.
After replacing the steering angle position sensor, replacing steering mechanical parts (such as steering gearbox, steering column, end tie rod, steering knuckle), performing four-wheel alignment, or repairing the car body, you must reset the steering angle.
The operation guidelines of the SAS function are shown as below:
- Enter the SAS menu and choose relevant models according to the vehicle being tested.
- Enter the Set steering angle sensor menu and follow the instructions displayed.
- Wait until the following instruction is displayed and press Yes after completing the instructions shown.
- Follow the instructions displayed and press OK after completing the instructions shown.
Message of 'Function execution is completed' displayed when SAS reset function has successfully completed.
BMS (Battery Management System) Reset
The Battery Management System (BMS) allows the scan tool to evaluate the battery charge state, monitor the close-circuit current, register the battery replacement and activate the rest state of the vehicle.
This function enables you to perform a resetting operation on the monitoring unit of the vehicle battery, in which the original low battery fault information will be cleared and battery matching will be performed.
Battery matching must be performed in the following cases:
- The main battery is replaced. Battery matching must be performed to clear original low battery information and prevent the related control module from detecting false information. If the related control module detects false information, it will invalidate some electric auxiliary functions, such as automatic start & stop function, sunroof without one-key trigger function or power window without automatic function.
- Battery matching is performed to re-match the control module and motoring sensor to detect battery power usage more accurately, which can avoid an error message displayed on the instrument cluster.
The operation guidelines of the BMS Reset function are shown as below:
- Enter the BMS Reset menu and choose relevant models according to the vehicle being tested.
- Turn on the ignition switch.
- Press OK to continue the BMS function.
- Enter battery capacity (within the given range) and press OK after the input.
- Enter the battery manufacturer and press OK after the input.
- Enter the 10-digit battery serial number and press OK after the input.
DPF (Diesel Particulate Filter) Regeneration
The Diesel Particle Filter (DPF) function manages DPF regeneration, DPF component replacement teach-in, and DPF teach-in after replacing the ECM.
The ECM monitors driving style and selects a suitable time to employ regeneration. Vehicles driven a lot at idling speed and low load will attempt to regenerate earlier than vehicles driven more with higher load and speed. For regeneration to take place, a prolonged high exhaust temperature must be obtained.
In the event of the car being driven in such ways that regeneration is not possible, i.e., frequent short journeys, a diagnostic trouble code will eventually be registered in addition to the DPF light and "Check Engine" indicators displaying. A service regeneration can be requested in the workshop using the diagnostic tool.
DPF regeneration is used to clear PM (Particulate Matter) from the DPF filter through continuous combustion oxidation mode (such as high-temperature heating combustion, fuel additive or catalyst reduce PM ignition combustion) to stabilize the filter performance.
DPF regeneration may be performed in the following cases:
- The exhaust back pressure sensor is replaced.
- The PM trap is removed or replaced.
- The fuel additive nozzle is removed or replaced.
- The catalytic oxidizer is removed or replaced.
- The DPF regeneration MIL is on and maintenance is performed.
- The DPF regeneration control module is replaced.
The operation guidelines of the DPF function are shown as below:
- Enter the DPF menu and choose relevant models according to the vehicle being tested.
- Enter the DPF regeneration menu.
- Read carefully and complete the requisites listed before performing the DPF regeneration function. Press OK after completing the instructions shown.
- Read the fuel tank level and make sure that it fulfills the requirement displayed.
- Read the carbon deposit load.
- Choose the "drive to warm up" option and follow the instructions listed below. Press OK after completing the instructions shown.
- Read the instructions carefully and follow the instructions shown on the screen. Press OK after completing the instructions shown.
- Follow the instructions displayed and press OK after completing the instructions shown. IMPORTANT: Please pay attention to the Note.
- Press the OK button to start the regeneration.
- Wait for the value of carbon deposit to decrease until a message of 'Emergency regeneration has been completed' pops up; this process may take up to 40 minutes.
- Wait for 2 minutes to let the particulate filter cool down.
- Press drop out to exit the DPF function.
Injector Coding
This function can write the identification code of the fuel injector into the ECU so that the ECU can recognize the new injector.
After the ECU or injector is replaced, the injector code of each cylinder must be confirmed or re-coded so that the cylinder can better identify injectors to accurately control fuel injection.
In general cases, there is no need to perform the coding matching function after cleaning. The identification of the fuel injector includes its working accuracy value and type value. When replacing an injector you need to find the corresponding model for replacement. At present, mainstream cars support injector coding functions.
The operation guidelines of the Injector Coding function are shown as below:
- Enter the Injector coding menu and choose relevant chassis models according to the vehicle being tested.
- Enter the Fuel injection nozzle injection volume adjustment menu.
- Read the note displayed carefully and press OK after the reading.
- Read and confirm the value stored in the cylinders.
- Enter the Change the value of cylinder menu of the replaced injector(s), enter the new 5-digit value, and then press OK.
- Wait until the message 'Write successfully' pops up.
- Turn off the ignition switch.
- Wait until the message asks you to turn on the ignition switch.
- Re-enter the Fuel injection nozzle injection volume adjustment menu to check whether the new value(s) are shown.
TPMS (Tire Pressure Monitoring System) Reset
This function allows to perform the learning and matching and resetting functions of the tire pressure sensor.
TPMS Reset may be performed in the following cases:
- Tire replacement
- After troubleshooting tire pressure related problems
- Other causes of loss of signal from the tire pressure sensor
Important Notes for TPMS Reset:
- For tire pressure sensor matching, some vehicle models may need the TPMS activation tool.
- After learning process, you may need to run the car for some while before the fault light goes off.
- Tire pressure imbalance may also cause the tire pressure light.
- This function is only available for activated tire pressure sensors. If you have a brand-new sensor, please use the professional tire pressure device.
Even for the same model, its tire pressure system may differ by the region where it is manufactured. Therefore, under the TPMS Reset function, we provide 6 menus for the major automotive manufacturing regions, including Korea, Japan, USA, China, Australia and Europe.
TPMS reset can be further divided into 4 methods, such as Automatic Relearn, Static Relearn, Copy ID and OBD Relearn, which is depending on the specific model. Also, even if the relearning methods are the same, the learning procedure may differ.
AUTOMATIC RELEARN:
- Install tire pressure sensor appropriately.
- Adjust all TPMS sensors to the standard value.
- Keep the vehicle at a complete standstill status for more than 20 minutes (with the engine off and power off).
- Drive at 30-100km/h for more than 15 minutes.
- The vehicle will automatically relearn the value; after that, the tire pressure warning will disappear.
- If the relearn procedure fails, please repeat steps 2-5.
STATIC RELEARN:
- Install all tire pressure sensors appropriately.
- Pull up the parking brake.
- Turn the ignition to ON/RUN with the engine off.
- Enter the tire pressure learning mode through the instrument panel on vehicle. There will be the corresponding prompt, which are differ from different car make and model, please subject to the vehicle manual or consult a professional.
- Starting from the left front wheel (some models flash the turn signal at the corresponding position), use the TPMS Activation Tool to activate the sensor, and the vehicle will sound the horn or flash the turn signal at the corresponding position after successful activation.
Note: The first sensor should be learned within 2 minutes, otherwise please repeat step 4.
After the left front wheel sensor is successfully relearned. For the remaining, please activate the remaining tire pressure sensors in the order of right front, right rear and left rear. The prompt and activation success status are the same as step 5.
OBD RELEARN:
- A TPMS Activation Tool is needed.
- Install tire pressure sensor appropriately.
- Adjust all TPMS sensors to the standard value.
- Activate all sensors in the order of left front, right front, right rear, left rear.
- Connect TPMS Activation Tool to the OBD port of vehicle and perform the OBD relearn function to write the sensor ID.
- Turn the ignition to ON/RUN, re-trigger all sensors in the order of left front, right front, right rear, left rear.
- Keep the vehicle powered off for more than 25 minutes.
- Drive at 30-100km/h for more than 15 minutes. If relearn successful, the tire pressure warning light will go off. Otherwise, please repeat steps 4-7.
COPY ID RELEARN:
Note: This learning method of the vehicle can only copy ID to the new sensor through the following three methods to replace the original sensor; if the new sensor cannot change its own ID, then the sensor can only be replaced by the OEM equipment!
Method 1:
- Use a TPMS Activation Tool to activate the original sensor, copy the sensor ID to the tire pressure activation device.
- And then program the copied ID into the new sensor through the TPMS Activation Tool (The binary of ID format should be the same as the original sensor).
- Remove the original sensor that has been just copied the ID, install the new sensor that has just been programmed, and put the tire back on.
Method 2:
- Use the TPMS Activation Tool to connect the vehicle OBD port, enter the tire pressure system, copy the ID of the sensor to be replaced.
- And then program the copied ID into the new sensor through the TPMS Activation Tool (The binary of ID format should be the same as the original sensor).
- Remove the original sensor that has been just copied the ID, install the new sensor that has just been programmed, and put the tire back on.
Method 3:
- Remove the original sensor.
- Use the TPMS Activation Tool to copy the original sensor ID into the new sensor manually (The binary of ID format should be the same as the original sensor).
- Install the new sensor to the tire correctly, set the tire pressure to the standard value, and put the tire back on the vehicle.
Note: Tire pressure standard is usually displayed in these places:
- Vehicle owner's manual
- Label next to the driver's door (near the B-pillar)
- Drawer next to the driver's seat of the vehicle
- Fuel tank cap
This Scan Tool is not a replacement for the TPMS activation tool, and it only provides TPMS Reset/Relearn function but not activation of TPMS sensors. If you need a professional TPMS activation tool, please consult your local dealer.
6. Troubleshooting
- Device Not Recognized / Functionality Issues: If your vehicle model is not recognized or a function does not work as expected, ensure all software is updated to the latest version via the 'Updates' menu in the Diagnostic APP settings. If issues persist, manually select the engine system to read ECU information or contact XTOOL technical support with your VIN code.
- Unstable Data Transmission: For functions like ECU programming & coding, always use the USB 3.0 to TYPE-B main cable to connect the tablet to the VCI box to ensure stable data transmission and prevent damage.
- Diagnostic Interruption: When running a Diagnostics function, do not shut down the scan tool directly. Always cancel the task before returning to the main interface and then shutting down the scan tool.
- Persistent Trouble Codes: If trouble codes are erased but the underlying issue remains unresolved, the codes will reappear after the next diagnostic test. Address the root cause of the problem.
- Flash Update Failures: Common causes for incomplete flash updates include poor cable connections between the tablet, VCI, and vehicle; the vehicle ignition being switched off prematurely; or low vehicle battery voltage. Recheck all connections and ensure stable power.
- Language Switching Issues: If you cannot switch languages at will, update the APP to the latest version ('Diagnossis' APP > Setting > APP). If further assistance is needed, send the device's S/N to XTOOL support to change the language configuration.
- FCA AutoAuth Access: Access to the Security Gateway Module on 2018+ Fiat/Chrysler/Dodge vehicles requires the buyer to register an FCA account.
7. User Tips
- Language Setup: The device supports 22 languages. During initial activation, you can select your preferred language. If you need to change it later, go to 'Diagnossis' APP > Setting > Language. If you encounter issues, ensure your APP is updated or contact support with your device's S/N.
- Key Programming: While the D9S PRO offers extensive key programming features, note that it may require additional equipment (accessories like KC501, KC100, M822, KS01, SK1) for certain functions or vehicle models. Always verify compatibility before attempting key programming.
- Software Updates: Take advantage of the 3 years of free software updates to ensure your device has the latest features and vehicle coverage. Even after the free update period, the device will continue to function normally with the last updated software.
- Vehicle Compatibility: The D9S PRO supports a wide range of vehicles, but not all models are universally compatible with every function. It's recommended to check compatibility with XTOOL support (providing your vehicle's Make/Model/Year/VIN) before purchasing or attempting advanced procedures.
- FCA AutoAuth: For FCA AutoAuth functions on compatible vehicles, remember that an FCA account registration is required.
- Wireless Connection: The advanced Wi-Fi connection offers a wider range (33-66ft) and faster, more stable data transmission compared to older Bluetooth scan tools, enhancing efficiency in the workshop.
8. Specifications
| Attribute | Value |
|---|---|
| Brand Name | XTOOL |
| Model Name | XTOOL D9S Pro |
| Display Size | 9.7 inches |
| OS System | Android 10.0 |
| Processor | Quad-core processor 1.5GHz |
| Storage | 4G+128G |
| Battery | 6400mAh 7.3V |
| Hardware Version | 2026 |
| Software Version | Upgradable |
| Special Features | Bluetooth, Wifi |
| External Testing Certification | ce |
| Certification | CE |
| Item Type | Engine Analyzer |
| Material | Plastic |
| Item Weight | 8kg |
| Item Height | 18cm |
| Item Width | 22cm |
| Item Length | 35cm |
| Is Batteries Included | Yes |
| Electronic | Yes |
| Use | Not Telecommunication |
| High-concerned chemical | None |
| 22 Languages | English, Spanish, French, German, Polish, Portuguese, Russian, Danish, Greek, Finnish, Hungarian, Italian, Japanese, Korean, Dutch, Norwegian, Swedish, Thai, Arabic, Turkish, Vietnamese, Traditional Chinese. |
| Warranty | 2 Years Warranty |
| Update | 3 Years Free Online Update |

Figure 28: Premium Hardware Configuration
9. What's Included (Packing List)
Accessories
- 1PC X Main Units Tablet
- 1PC X VCI Box
- 1PC X Type-C to Type-B Data Cable
- 1PC X Type-C to Type-A Data Cable
- 1PC X Type-C to Type-C Charger Cable
- 1PC X Power Cable US
- 1PC X Quick Start Guide
- 1PC X Power Cable EU
- 1PC X Power Cable UK
- 1PC X Color Carton
- 1PC X Packing List
- 1PC X Tool Case
- 1PC X Desiccant
Test Connectors
- 1PC X OBD II-16
- 1PC X DB15 Main Cable
- 1PC X Cigar Lighter Cable
- 1PC X For HONDA-3
- 1PC X For TOYOTA-17
- 1PC X For BMW-20
- 1PC X For KIA-20
- 1PC X For MAZDA-17R
- 1PC X For NISSAN-14
- 1PC X For GM/DAEWOO-12
- 1PC X For SUZUKI-3
- 1PC X For FIAT-3
- 1PC X For HYUNDAI/KIA-10
- 1PC X For AUDI-4
- 1PC X For MITSUBISHI-12+16
- 1PC X For UNIVERSAL-3
- 1PC X For BENZ-38
- 1PC X For BENZ-14
- 1PC X For CITROEN-2

Figure 29: What's Included in the Package
10. Warranty & Support
Warranty
Shenzhen XTOOLtech Intelligent Co., LTD. (the Company) warrants to the original retail purchaser of this XTOOL device that should this product or any part thereof during normal usage and under normal conditions be proven defective in material or workmanship that results in product failure within ONE YEAR from the date of purchase, such defect(s) will be repaired, or replaced (with new or rebuilt parts) with Proof of Purchase, at the Company's option, without charge for parts or labor directly related to the defect(s).
The Company shall not be liable for any incidental or consequential damages arising from the use, misuse, or mounting of the device.
This warranty does not apply to:
- Products subjected to abnormal use or conditions, accident, mishandling, neglect, unauthorized alteration, misuse, improper installation/repair, or, improper storage.
- Products whose mechanical serial number or electronic serial number has been removed, altered, or defaced.
- Damage from exposure to excessive temperature or extreme environmental conditions.
- Damage resulting from connection to, or use of any accessory or other product not approved or authorized by the Company.
- Defects in appearance, cosmetic, decorative, or structural items such as framing and non-operating parts.
- Products damaged from external causes such as fire, dirt, sand, battery leakage, blown fuse, theft, or improper usage of any electrical source.
Software Updates
The device comes with 3 Years Free Online Update. After activating the device, please update the software modules identified in the "Updates" screen. The device will identify all currently available software packages, and you can download them as needed. All software updates are directly via the Internet. To access the update application, open the Diagnostic application and click Updates.
When the subscription expires, the software installed on your device itself is still available, but all updates will be invalid. If you delete specific software due to personal operation, XTOOL is not responsible for supporting the restoration of the software when the subscription expires.
To renew your subscription, please contact your local dealer, or contact XTOOL technical support team directly.
Remote Assistance
Tap on "Remote" to start the TeamViewer quick support program, which is a simple, fast, and secure remote-control screen. You can use this application to enable someone else to use their computer running TeamViewer software to control your tablet over the Internet. This feature is frequently used by XTOOL's technical support centre when remotely helping customers with technical support.
To obtain remote support from your partners or XTOOL AfterSalesService Center: support1@xtooltech.com | support2@xtooltech.com
- Turn on the power of the tablet.
- Click Remote in the Diagnostic application. The TeamViewer screen is displayed, and the device ID will be generated.
- Your partner must install the remote-control software on their computer by downloading the full version of the TeamViewer program (http://www.teamviewer.com) online, and then start the software on their computer at the same time, to provide support and remote control of the tablet.
- Provide your ID to the partner or XTOOL technician, and then wait for them to send you a remote-control request.
- A pop-up window will be displayed, asking you to permit the remote-control program to control your device.
- Click Allow to accept, or click Reject to reject.