KeKeQeen LT455CW

Contents

LT455CW Ceramic Filter Instruction Manual

Model: LT455CW | Brand: KeKeQeen

1. Introduction

The KeKeQeen LT455CW is a compact, high-selectivity ceramic filter designed for intermediate frequency (IF) applications in various electronic circuits. This component is commonly used in radio receivers, transceivers, and other communication equipment to provide precise frequency filtering. Its DIP-5 package allows for easy integration onto printed circuit boards.

Front view of a single LT455CW ceramic filter
Figure 1: Front view of the LT455CW ceramic filter. This image shows the compact size and marking of the component.

2. Features

  • Low profile design, suitable for space-constrained applications.
  • High selectivity for effective signal filtering.
  • Available in various bandwidths (B to J) to meet diverse application requirements.
  • Designed for easy mounting on any standard Printed Circuit Board (PCB).
  • Wide operating temperature range: -20°C to +80°C.
  • Storage temperature range: -40°C to +85°C.

3. Specifications

The following table details the electrical and environmental specifications of the LT455CW ceramic filter:

Table of electrical specifications for the LT455CW ceramic filter
Figure 2: Detailed electrical specifications of the LT455CW ceramic filter.
LT455CW Ceramic Filter Specifications
ParameterValue
Operating Temperature Range-20°C to 80°C
ShapeLead
Elements6
Center Frequency455.0 KHz
Nominal Center ValueYes
6dB Bandwidthfn ± 3.0 KHz min.
Stop Bandwidth9.0 KHz
Area of Stop Bandwidth[within 50dB]
Stop Band Attenuation60dB [within fn ± 100KHz]
Insertion Loss6.0dB [at minimum loss point]
Ripple2.0dB [within fn ± 2KHz]
Input/Output Impedance2000 Ω

4. Dimensions and Pinout

The LT455CW ceramic filter features a 5-pin Dual In-line Package (DIP-5). Refer to the diagram below for physical dimensions and pin assignments.

Diagram showing dimensions and pinout for the LT455CW ceramic filter
Figure 3: Dimensions in millimeters and pin configuration of the LT455CW.

Pin Configuration:

  • Pin (1): Input
  • Pins (2), (3), (4): Ground
  • Pin (5): Output

Dimensions (approximate):

  • Length: 11.0 mm
  • Width: 7.0 mm
  • Height: 4.0 mm

5. Setup and Installation

The LT455CW ceramic filter is a through-hole component designed for soldering onto a Printed Circuit Board (PCB). Follow these general guidelines for proper installation:

  1. Preparation: Ensure your PCB is clean and free of contaminants. Identify the correct mounting location for the filter.
  2. Orientation: Carefully align the pins of the LT455CW with the corresponding holes on the PCB, paying close attention to the pinout diagram (Figure 3) to ensure correct input/output and ground connections. Incorrect orientation can lead to malfunction or damage.
  3. Insertion: Gently insert the pins into the PCB holes. Do not force the component, as this may bend or damage the pins.
  4. Soldering: Solder each pin to its respective pad on the PCB. Use appropriate soldering techniques to ensure strong, reliable electrical connections without creating solder bridges. Avoid excessive heat, which can damage the component.
  5. Inspection: After soldering, visually inspect all connections for proper solder joints, correct orientation, and absence of shorts.

For specific circuit integration, consult the schematic and layout guidelines of your overall electronic design.

6. Operating Instructions

Once correctly installed, the LT455CW ceramic filter operates passively within your circuit. It requires no external power or configuration beyond its proper integration into the signal path.

  • Signal Path: Connect the input pin (1) to the signal source and the output pin (5) to the next stage of your circuit.
  • Grounding: Ensure all ground pins (2, 3, 4) are securely connected to the circuit's ground plane to maintain optimal performance and noise rejection.
  • Frequency Range: The filter is designed for a center frequency of 455.0 KHz. Ensure the signals you intend to filter are within the effective bandwidth of this component for optimal performance.
  • Environmental Conditions: Operate the component within its specified operating temperature range (-20°C to +80°C) to ensure stable and reliable performance.

7. Maintenance

The LT455CW ceramic filter is a robust, passive electronic component that generally requires minimal maintenance. Adhere to the following for longevity:

  • Cleanliness: Keep the surrounding area of the component on the PCB clean and free from dust, dirt, and moisture. Use appropriate cleaning agents for electronics if necessary, ensuring the circuit is powered off.
  • Environmental Control: Store and operate the component within the specified temperature and humidity ranges to prevent degradation.
  • Physical Inspection: Periodically inspect the solder joints for any signs of cracking or corrosion, especially in environments with significant vibration or temperature fluctuations.

8. Troubleshooting

If your circuit is not performing as expected after installing the LT455CW filter, consider the following troubleshooting steps:

  • Check Connections: Verify all pins are correctly soldered and that there are no cold joints or solder bridges. Ensure the input, output, and ground connections are accurate according to the pinout diagram.
  • Correct Orientation: Double-check that the filter is inserted with the correct orientation.
  • Signal Integrity: Use an oscilloscope or spectrum analyzer to check the signal at the input and output of the filter to confirm it is receiving the expected signal and producing the filtered output.
  • Component Damage: While rare, physical damage during handling or soldering can occur. Inspect the component for any visible cracks or damage.
  • Circuit Design: Ensure the filter's specifications (e.g., center frequency, bandwidth, impedance) are compatible with the requirements of your overall circuit design.

9. User Tips

  • CB Radio Applications: The LT455CW ceramic filter is suitable for use in CB (Citizens Band) radios, often employed in the IF stage for signal selectivity.
  • Impedance Matching: For optimal performance, ensure proper impedance matching between the filter and the preceding/succeeding stages of your circuit, especially considering its 2000 Ω input/output impedance.

10. Warranty and Support

This KeKeQeen LT455CW ceramic filter is manufactured to high standards. For any technical inquiries or support, please contact the seller, KeKeQeen Store, directly through the platform where the purchase was made. Please refer to your purchase documentation for specific warranty terms, if applicable.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.