Nidec 27H060D180

Contents

Nidec Brushless DC Motor 27H060D180 User Manual

Model: 27H060D180

1. Product Overview

This document provides instructions for the Nidec 12V/24V Brushless DC Motor, model 27H060D180. This motor features an integrated drive, supporting both positive and negative rotation, and an electronic brake function. It is designed for applications requiring precise control and reliable operation within its specified voltage range.

Nidec Brushless DC Motor without gear, showing the Nidec label, model number, and wiring harness.
Nidec Brushless DC Motor (without gear) with integrated drive board and wiring harness.
Nidec Brushless DC Motor with an attached gear, next to a coin for scale.
Nidec Brushless DC Motor with an optional gear attached.
Close-up view of the motor's internal drive board with electronic components.
Internal view of the motor's integrated drive board.

2. Safety Precautions

  • Polarity Warning: The positive and negative poles of this DC brushless motor must be connected correctly. Reversing the polarity (black line to positive, white line to negative) will burn out the drive board.
  • Ensure all connections are secure before applying power.
  • Do not attempt to disassemble the motor or drive board unless you are a qualified technician.
  • Keep the motor away from water, excessive heat, and corrosive environments.

3. Setup and Wiring

The motor comes with a pre-attached wiring harness. Note that the wire colors may not correspond to standard conventions; always refer to the specific connection definitions below, which are based on the order of the leads.

3.1 Wiring Diagram and Definitions

Detailed wiring diagram for the Nidec brushless DC motor, showing color-coded wires and their functions: positive, negative, starting wire, brake, and direction.
Wiring Diagram for Nidec Brushless DC Motor.
  • Black Line: Positive terminal of the power supply.
  • White Line: Negative terminal of the power supply.
  • Red Line: Direction control line. Connect to the negative pole (white line) for Clockwise (CW) rotation. Disconnect for Counter-Clockwise (CCW) rotation.
  • Blue Line: Starting line. Connect with a 10K resistor in series to the positive pole (red line) to start the motor. Disconnect to stop the motor. If using DC12V, the blue line can be directly connected to the positive pole without a resistor. For DC24V, the 10K resistor is mandatory.
  • Yellow Line: Emergency stop line. Connect to the blue line to stop the motor (brake). Disconnect to release the brake and allow operation.
  • Green Line: Purpose unknown. Leave unconnected.

3.2 Initial Connection Steps

  1. Connect the Black Line to the positive terminal of your DC power supply.
  2. Connect the White Line to the negative terminal of your DC power supply.
  3. For starting the motor, connect the Blue Line to the positive pole. If using a 24V power supply, ensure a 10K resistor is in series with the blue line. For 12V, a resistor is not strictly necessary but can be used for safety.
  4. To control direction, connect the Red Line to the white line (negative) for CW rotation, or leave it disconnected for CCW rotation.
  5. For emergency stop/brake, connect the Yellow Line to the blue line. Disconnect it to resume normal operation.
  6. Ensure the Green Line remains unconnected.

4. Operating Instructions

This motor operates within a voltage range of DC12V to DC24V. It does not support PWM speed regulation.

4.1 Starting and Stopping

  • To Start: Ensure the Yellow Line is disconnected from the Blue Line. Connect the Blue Line (with 10K resistor for 24V) to the positive power supply.
  • To Stop: Disconnect the Blue Line from the positive power supply.
  • Emergency Stop/Brake: Connect the Yellow Line to the Blue Line. This will engage the electronic brake.

4.2 Direction Control

  • Clockwise (CW) Rotation: Connect the Red Line to the White Line (negative terminal).
  • Counter-Clockwise (CCW) Rotation: Leave the Red Line disconnected.

4.3 Video Demonstration

Demonstration of the Nidec Brushless DC Motor in operation.

5. Maintenance

This brushless DC motor is designed for low maintenance. Follow these guidelines to ensure longevity:

  • Keep the motor clean and free from dust and debris.
  • Avoid exposing the motor to extreme temperatures or humidity.
  • Regularly check wiring connections for looseness or damage.
  • Do not lubricate the motor shaft unless specifically instructed by the manufacturer.

6. Troubleshooting

  • Motor does not start:
    • Check power supply connections (Black and White lines) for correct polarity and secure contact.
    • Ensure the Blue Line (starting line) is correctly connected to the positive pole (with 10K resistor for 24V).
    • Verify that the Yellow Line (emergency stop) is disconnected from the Blue Line.
  • Motor runs in wrong direction:
    • Check the connection of the Red Line (direction control). Disconnect for CCW, connect to White Line for CW.
  • Motor stops unexpectedly:
    • Check if the Yellow Line (emergency stop) has accidentally connected to the Blue Line.
    • Verify stable power supply.
  • Motor drive board burns out:
    • This typically indicates incorrect polarity connection (Black and White lines reversed). Always double-check polarity before applying power.

7. Specifications

Feature Specification
Model 27H060D180
Rated Voltage DC24V
Applicable Voltage DC12V - DC24V
Speed (DC12V) 2175 RPM (0.15A)
Speed (DC18V) 3360 RPM (0.18A)
Speed (DC24V) 4600 RPM (0.21A)
Outer Diameter 49 mm
Motor Height 31.9 mm
Motor Shaft Diameter 3.15 mm
Output Shaft Length 14.5 mm
Weight 202 g
Speed Regulation No PWM support
Certification CCC
Origin Mainland China
Side view of the motor with dimensions labeled: 49mm height, 3.15mm shaft diameter, 34.9mm body diameter, 14.5mm shaft length, and 202g weight.
Motor dimensions (side view).
Top view of the motor showing mounting hole dimensions: M3 screws, 28mm spacing between holes.
Motor mounting dimensions (top view).
Technical drawing showing external dimensions and rotation direction (CCW) of the 27H type motor, including connector details.
External Dimensions Technical Diagram.

8. User Tips

  • Always verify the voltage of your power supply before connecting the motor.
  • For 24V operation, remember the 10K resistor for the blue starting line to prevent damage.
  • If experimenting with the motor, it's advisable to start with a lower voltage (e.g., 12V) to familiarize yourself with its operation before moving to higher voltages.
  • Consider using a multimeter to confirm wire functions if you are unsure, especially given the note about non-standard wire colors.

9. Warranty and Support

For any issues or technical support, please contact the seller or manufacturer directly. Keep your purchase records for warranty claims. Specific warranty terms may vary by region and seller policy.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.