Introduction
This manual provides instructions for the installation, operation, maintenance, and specifications of your BUCKLOS MTB Air Suspension Fork. Please read this manual thoroughly before installation and use to ensure proper function and safety.

Specifications
The BUCKLOS Air Suspension Forks are designed for Mountain Bikes, Downhill Bikes, and E-bikes, featuring an oil and gas damping system. Key specifications vary by model as detailed below.
General Specifications
| Feature | Description |
|---|---|
| Brand Name | BUCKLOS |
| Type | Oil and Gas Fork (Air Resilience/Oil Damping) |
| Use | Mountain Bikes, Downhill Bikes, E-bikes |
| Fit For | Disc Brake |
| Suspension | Yes, Air Suspension |
| Material | Aluminum Alloy |
| Steerer Tube Diameter | 28.6mm (1-1/8'' Threadless) |
| Axle Type | 15*110mm Thru Axle |
| Lockout Way | Manual Lockout |
| Package Included | 1pc*BUCKLOS Fork |
Model-Specific Specifications
| Model | Wheel Size | Support Tyre Size | Steerer Tube Type | Travel | Stroke Tube Diameter | Weight (Approx.) |
|---|---|---|---|---|---|---|
| B712 (Boost Air Fork) | 27.5 Inch / 29 Inch | 2.3 inch maximum width | Tapered Tube | 160mm | 36mm | 27.5": 2107g, 29": 2172g |
| B713 (Dual Crown Boost Air Fork) | 27.5 Inch / 29 Inch | 2.3 inch maximum width | Tapered Tube | 180mm | 36mm | 27.5": 2762g, 29": 2818g |
| B714 (Inverted Air Fork) | 29 Inch (fits 26/27.5/29 Inch) | 2.8 inch maximum width | Tapered Tube | 140mm | 34mm | 2750g |
| B715 (Dual Crown Inverted Air Fork) | 29 Inch (fits 26/27.5/29 Inch) | 2.8 inch maximum width | Straight Tube/Tapered Tube | 180mm | 34mm | 3560g |
Dimensional Diagrams




Setup and Installation
Proper installation is crucial for the performance and safety of your suspension fork. If you are unsure about any steps, consult a professional bicycle mechanic.
- Unpacking: Carefully remove the fork from its packaging. Inspect for any visible damage. A boxed fork is shown in Figure 6.
- Steerer Tube Preparation: The steerer tube may need to be cut to the appropriate length for your bicycle frame and stem. Ensure precise measurement before cutting.
- Crown Race Installation: Install the crown race onto the steerer tube.
- Fork Installation: Insert the steerer tube through the head tube of your bicycle frame. Install the headset bearings, spacers, and stem according to your bicycle manufacturer's instructions.
- Thru-Axle Installation: Secure the wheel into the fork dropouts using the 15x110mm thru-axle. Ensure it is tightened to the manufacturer's specifications.
- Brake Caliper Installation: Mount your disc brake caliper to the fork's A-pillar (74mm hole pitch). Ensure proper alignment and torque specifications are met for the brake system.
- Brake Line Routing: Use the integrated brake line fixed buckle to route the brake hose securely along the fork leg.






Operating Your Suspension Fork
Your BUCKLOS air suspension fork offers adjustable settings to optimize your riding experience across various terrains.
- Air Chamber Adjustment: The fork uses air as a rebound medium. Adjust the air pressure in the air chamber to achieve the desired shock absorbing effect and sag for your weight and riding style. Use a high-pressure shock pump (not included) for this adjustment.
- Suspension Lockout: The manual lockout feature allows you to stiffen the fork for climbing or smooth terrain, improving pedaling efficiency. Turn the lockout knob to the "Lock" position to engage and "Open" to disengage.
- Damping Adjustment: Adjust the rebound damping to control how quickly the fork extends after compression. Turn the damping adjustment knob (often red or blue) to achieve a faster or slower rebound speed, matching the road conditions and your preference.
- Compression Adjustment (B713, B714, B715): These models may feature additional compression adjustment to control how quickly the fork compresses. Refer to the specific model's diagram for location and adjustment.

Maintenance
Regular maintenance will prolong the life and performance of your BUCKLOS suspension fork.
- Cleaning: After each ride, especially in wet or muddy conditions, clean the stanchions (inner tubes) and seals with a soft cloth and mild soap and water. Avoid high-pressure washing directly at the seals.
- Lubrication: Apply a small amount of suspension-specific lubricant to the stanchions periodically to keep the seals supple and reduce friction. Cycle the fork a few times after application.
- Air Pressure Check: Regularly check the air pressure in the air chamber using a high-pressure shock pump. Refer to your preferred sag settings or manufacturer recommendations for appropriate pressure.
- Inspection: Periodically inspect the fork for any signs of damage, leaks, or loose bolts. Pay attention to the thru-axle, brake caliper bolts, and crown area.
- Professional Service: For internal service, such as oil changes or seal replacement, it is recommended to take your fork to a qualified bicycle mechanic.
Troubleshooting
Here are some common issues and potential solutions for your suspension fork.
| Problem | Possible Cause | Solution |
|---|---|---|
| Fork feels too soft or bottoms out easily | Low air pressure in the air chamber. | Add air to the air chamber using a high-pressure shock pump until desired sag is achieved. |
| Fork feels too stiff or doesn't use full travel | Too much air pressure in the air chamber. | Release air from the air chamber until desired sag is achieved. |
| Fork rebounds too quickly (pogo stick effect) | Rebound damping set too fast. | Increase rebound damping (turn knob towards 'slow' or '+'). |
| Fork rebounds too slowly (packs up) | Rebound damping set too slow. | Decrease rebound damping (turn knob towards 'fast' or '-'). |
| Oil leak around seals | Worn seals or damaged stanchions. | Clean stanchions. If leak persists, professional service is required for seal replacement. |
| Unusual noises (creaking, clunking) | Loose components, dry bushings, or internal damage. | Check all bolts (thru-axle, brake caliper, stem). If noises persist, seek professional inspection. |
User Tips
- Check Compatibility: Before purchasing or installing, ensure the fork's wheel size, steerer tube type (tapered/straight), and axle type (15x110mm Thru Axle) are compatible with your bicycle frame and wheelset.
- Additional Parts: Be aware that assembly may require additional parts not included with the fork, such as a star nut, headset, or specific tools for steerer tube cutting.
- Air System: Confirm that the suspension is indeed an air system, which allows for fine-tuning of stiffness based on rider weight and preference.
- Packaging Inspection: Upon receiving the package, carefully inspect it for any signs of damage before opening. If damage is noted, document it with photos or video before proceeding.
Warranty and Support
BUCKLOS is committed to providing quality products. For any issues or support, please refer to the following:
- Product Issues: If you encounter any problems with the product, especially regarding damage or defects, it is recommended to contact the seller directly with photos or videos of the issue.
- Delivery Guarantee: The product is covered by a delivery guarantee which includes compensation for delayed delivery, refunds for lost packages, and refunds for damaged items.
For further assistance, please contact BUCKLOS Official Store customer service.