FENVI 1200M WiFi Repeater

Contents

FENVI 1200Mbps Dual-Band WiFi Repeater

Model: 1200M WiFi Repeater

1. Product Overview

The FENVI 1200Mbps Dual-Band WiFi Repeater is designed to extend the range of your existing Wi-Fi network, eliminating dead zones and providing strong, stable internet connectivity throughout your home or office. It supports both 2.4GHz and 5GHz frequency bands, offering high-speed data transfer and robust security features.

FENVI 1200Mbps Dual-Band WiFi Repeater

Figure 1: FENVI 1200Mbps Dual-Band WiFi Repeater

Video 1: FENVI 1200Mbps WiFi Repeater Product Overview

2. Setup Instructions

2.1. WPS Quick Setup

The WPS (Wi-Fi Protected Setup) method allows for a quick and easy connection to your existing router. Ensure your host router supports WPS.

  1. Plug the FENVI WiFi Repeater into a power outlet.
  2. Press the WPS button on your host router.
  3. Within 2 minutes, press the WPS button on the FENVI WiFi Repeater.
  4. Wait 1-2 minutes for the devices to connect. The Extender LED indicator should turn solid, indicating a successful connection.

Note: Your host router's SSID and password must be the same as the router's. Special characters in the password are not supported by the repeater.

WPS Quick Setup Diagram

Figure 2: WPS Quick Setup Diagram

2.2. Web Browser Setup (Repeater Mode)

For more detailed configuration or if WPS is not available, use the web browser setup method.

  1. Plug the FENVI WiFi Repeater into a power outlet.
  2. Connect your mobile phone or computer to the repeater's default Wi-Fi network. The network name will be 'Fvpro_5G' or 'Fvpro_2.4G' followed by the last 5 numbers of the MAC address. The default password is '12345678'.
  3. Open a web browser (e.g., Chrome, Firefox) and type http://192.168.188.1 in the address bar.
  4. Log in using the default username 'admin' and password 'admin'.
  5. Follow the on-screen instructions to select your host router's Wi-Fi network and enter its password.
  6. Review and confirm the new repeater network settings, then click 'Start Connect'.
Wireless Repeater Mode Setting Steps

Figure 3: Wireless Repeater Mode Setting Steps

3. Operating Modes

The FENVI WiFi Repeater supports two main operating modes:

  • Repeater Mode: Extends the range of an existing Wi-Fi network. This is the primary function, ideal for covering Wi-Fi dead zones.
  • AP (Access Point) Mode: Converts a wired network connection into a wireless one. This is useful for creating a new Wi-Fi hotspot from an Ethernet connection.

The device operates on dual bands: 2.4GHz and 5GHz. The 5GHz band offers faster speeds (up to 867Mbps) for interference-free HD video streaming and gaming, while the 2.4GHz band provides wider coverage (up to 300Mbps) and better wall penetration for general internet use like music streaming and email.

5G vs 2.4G Performance Comparison

Figure 4: 5G (867Mbps) vs 2.4G (300Mbps) Performance Comparison

Strong Wall Penetration Diagram

Figure 5: Strong Wall Penetration Capabilities

The repeater offers wide compatibility, supporting up to 35 devices including smartphones, tablets, laptops, smart TVs, and other Wi-Fi enabled devices.

Wide Compatibility Diagram

Figure 6: Wide Compatibility with various devices

4. Maintenance

To ensure the longevity and optimal performance of your FENVI WiFi Repeater, please observe the following maintenance guideline:

  • Avoid Prolonged Use: Do not use the repeater for extended periods (more than 24 hours continuously). If not needed, unplug the device from the power supply to protect its lifespan and reduce wear.

5. Troubleshooting

If you encounter issues with your FENVI WiFi Repeater, refer to the following common problems and solutions:

5.1. General Issues

  • Cannot connect to the internet after setup:
    Ensure the password entered for the repeater is identical to your router's password. Avoid using special characters (e.g., *&^%$#@!) in your router's password, as the repeater may not recognize them. If special characters are present, change your router's password.
  • Poor signal connection, slow speeds, or dropped connection:
    This can be caused by a weak signal from the main router. Try moving the repeater closer to your main router.
  • Cannot see the desired wireless network during setup:
    The repeater might be out of range of your main router. Move the repeater closer to the router and scan again.

5.2. Advanced Troubleshooting

  • How to reset the repeater:
    With the device powered on, long-press the reset button (located on the side, not the WPS button) for 10 seconds.
  • Cannot access the Repeater's web management page:
    1. Ensure your computer is connected to the extended network.
    2. Verify your computer is set to obtain an IP address automatically.
    3. If the repeater is connected to the router, check your router's DHCP client list to find the repeater's current IP address.
    4. If issues persist, reset the repeater and reconfigure.
  • Wireless transmission rate slows down when the signal is stronger after being repeated:
    In compliance with wireless transmission protocols, all repeater devices operate in half-duplex mode (one-way communication) rather than full-duplex. This means the transmission time is effectively doubled, leading to a decrease in speed. Repeaters are best used to extend coverage and eliminate dead zones, not necessarily to increase raw speed beyond the main router's capabilities.
  • Devices connected to the repeater cannot get an IP address or access the internet:
    1. Check if a wireless MAC filter, wireless access control, or Access Control List (ACL) is enabled on your main router. Log into your router and disable these features.
    2. The repeater might not be successfully connected to your router. Reset and reconfigure the repeater.
    3. The router's IP address might be occupied, or the number of connected wireless devices has reached its limit. Reboot your router, then reset and reconfigure the repeater.
Q&A illustration

Figure 7: General Q&A Illustration

6. Specifications

FeatureSpecification
Model Name1200M WiFi Repeater
Brand Namefenvi
TypeWireless
Frequency Band ClassDual-Band
Wi-Fi Supported Frequency2.4G & 5G
Wireless Communication Standard802.11ac
Wi-Fi Transmission Standard802.11ac
Standards And ProtocolsWi-Fi 802.11ac
Wireless Transmission Rate1200M
2.4G Wi-Fi Transmission Rate300 Mbps
5G Wi-Fi Transmission Rate867Mbps
Max. LAN Data Rate1000Mbs
Wired Transfer Rate10/100Mbps
LAN Ports1
WAN Ports1 x10/100Mbps
Supports WPSYes
Supports WDSNo
FunctionFirewall
With Modem FunctionNo
Number of USB InterfacesNone
ApplicationHome
CertificationCE
OriginMainland China
Package Dimensions (L x W x H)8 cm x 8 cm x 7 cm
Package Weight0.12 kg

7. Warranty and Support

For detailed warranty information, please refer to the seller's terms and conditions at the point of purchase. For additional support and a comprehensive guide, you can refer to the official user manual in PDF format:

8. User Tips

Based on user experiences and common questions, here are some tips for optimizing your FENVI WiFi Repeater:

  • Manage Speed Expectations: While the repeater extends coverage, expect some speed degradation, especially through walls or at greater distances. The device operates in half-duplex mode, which inherently reduces throughput compared to a direct connection to your main router. For example, a 660Mbps main connection might only yield around 90-160Mbps through the repeater, dropping further through obstacles.
  • Placement is Key: For best results, place the repeater in a location where it receives a good signal from your main router, but is also close enough to the areas where you need extended coverage. Avoid placing it behind thick walls or large metal objects.
  • Consider Usage: This repeater is ideal for extending Wi-Fi coverage to eliminate dead zones for general home use (browsing, streaming, smart home devices). It may not be suitable for professional use or applications requiring maximum sustained high-speed data transfer.
  • Dual-Band Advantage: Utilize both 2.4GHz for wider range and better wall penetration, and 5GHz for higher speeds in closer proximity, especially for bandwidth-intensive tasks like HD video or gaming.
  • Firewall Feature: The built-in firewall provides an additional layer of security by blocking unwanted traffic.
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.