FENVI 1200Mbps Dual-Band WiFi Repeater User Manual

1. Introduction

The FENVI 1200Mbps Dual-Band WiFi Repeater is designed to extend the range of your existing Wi-Fi network, eliminating dead zones and providing strong, stable internet connectivity throughout your home or office. It supports both 2.4GHz and 5GHz bands, offering high-speed data transfer and robust security features.

Figure 1: FENVI 1200Mbps Dual-Band WiFi Repeater

2. Safety Information

• Do not use the repeater for extended periods (more than 24 hours) without unplugging it to protect its lifespan.
• Ensure the device is placed in a well-ventilated area.
• Keep away from water and high humidity environments.
• Do not attempt to disassemble or repair the device yourself.

3. Product Overview

The FENVI WiFi Repeater features a compact, wall-mounted design with external antennas for enhanced signal coverage. It includes LED indicators and a WPS button for easy setup.

3.1. Device Layout

The device typically includes:

• LED Indicators: Extender, 5G, 2.4G, Power. These lights indicate the status of the device and network bands.
• WPS Button: For quick and easy connection to your router.
• LAN Port: For wired connections to devices or for AP mode setup.
• Power Plug: Integrated into the device for direct wall socket connection.

4. Setup and Configuration

The FENVI WiFi Repeater supports two main operating modes: Repeater Mode and Access Point (AP) Mode.

4.1. Repeater Mode (WPS Quick Setup)

This method allows for a quick connection to your existing router if it supports WPS.

1. Plug the FENVI Repeater into a power outlet near your main router.
2. Wait for the Power LED to become stable.
3. Press the WPS button on your main router.
4. Within 2 minutes, press the WPS button on the FENVI Repeater.
5. Wait 1-2 minutes for the devices to connect. The Extender LED on the repeater should light up, indicating a successful connection.

Note: Your host router must support WPS. The extended network's SSID and password will be the same as your router's. WPS may not support special characters in passwords.

Figure 2: WPS Quick Setup Guide

4.2. Repeater Mode (Web Browser Setup)

If your router does not support WPS, or for more advanced configuration, use the web browser method:

1. Plug the FENVI Repeater into a power outlet.
2. Connect your computer or mobile device to the repeater's default Wi-Fi network (e.g., "Fvpro_5G" or "Fvpro_2.4G", the last 5 numbers of the MAC address might be part of the SSID). The default password is typically "12345678".
3. Open a web browser (e.g., Chrome, Firefox) and type http://192.168.188.1 into the address bar.
4. Log in to the repeater's management page. The default username and password are usually "admin".
5. Follow the on-screen instructions to select your main Wi-Fi network and enter its password.
6. Confirm the settings and wait for the repeater to restart and connect.

Figure 3: Web Browser Setup for Repeater Mode

4.3. Access Point (AP) Mode

In AP mode, the repeater connects to your router via an Ethernet cable and broadcasts a new Wi-Fi network. This is ideal for converting a wired network into a wireless one.

1. Plug the FENVI Repeater into a power outlet.
2. Connect an Ethernet cable from your main router's LAN port to the LAN port on the FENVI Repeater.
3. Access the repeater's web management page (as described in section 4.2).
4. Select "AP Mode" from the configuration options.
5. Configure the new Wi-Fi network's SSID and password as desired.
6. Save the settings and wait for the repeater to restart.

5. Operating the Repeater

Once configured, the FENVI Repeater will automatically extend your Wi-Fi signal. You can connect your devices to the extended network just as you would to your main router.

5.1. Signal Coverage and Performance

The repeater is designed to provide strong wall penetration and wide compatibility with various devices.

Figure 4: Dual-Band Performance and Wall Penetration

Figure 5: Enhanced Signal Through Walls

The 5GHz band (up to 867Mbps) is ideal for interference-free HD video streaming and gaming, while the 2.4GHz band (up to 300Mbps) ensures better wireless performance for general internet use and penetrating walls.

Figure 6: Wide Device Compatibility

The repeater is compatible with a wide range of devices, including smartphones, tablets, laptops, smart TVs, and gaming consoles, supporting connections for up to 35 devices.

6. Specifications

7. Maintenance

• To ensure the longevity of your repeater, avoid continuous operation for more than 24 hours. Unplug the device from the power supply when not in use for extended periods.
• Keep the device clean and free from dust to maintain optimal performance.

8. Troubleshooting (FAQ)

Q1: Cannot connect to the internet after setup?

A1: Ensure the password entered for your router's Wi-Fi is correct. Avoid using special characters (e.g., *&^%$#@!) in your router's Wi-Fi password, as the repeater may not identify them. If special characters are present, change your router's password to a simpler one.

Q2: How to reset the repeater?

A2: With the repeater powered on, long-press the reset button (located on the side, not the WPS button) for 10 seconds. The device will restart with factory default settings.

Q3: What should I do if I cannot access the repeater's web management page (192.168.188.1)?

A3:

• Make sure your computer or mobile device is connected to the repeater's extended network or its default Wi-Fi network.
• Ensure your device is set to obtain an IP address automatically (DHCP).
• If the repeater is already connected to your main router, you might need to check your router's DHCP client list to find the repeater's assigned IP address.
• If all else fails, reset the repeater and try the configuration process again.

Q4: Why is the wireless transmission speed slower even if the signal is stronger after repeating?

A4: In compliance with wireless transmission protocols, all repeater devices operate in half-duplex mode. This means the repeater communicates with both the root router (or AP) and the client devices, effectively doubling the transmission time and potentially reducing speed. Repeaters are primarily for extending coverage to eliminate dead zones, not necessarily for increasing raw speed. Connect to the extender when your main network signal is weak or for wider coverage.

Q5: Why can't devices connected to the repeater get an IP address or access the internet?

A5:

• Check if you have enabled MAC filtering, wireless access control, or an Access Control List (ACL) on your main router. If so, log into your router and disable these features temporarily or add the repeater's MAC address to the allowed list.
• The repeater might not have successfully connected to your router. Reset the repeater and reconfigure it.
• The IP address range of your router might be exhausted, or the number of connected wireless devices has reached its limit. Reboot your main router, then reset and reconfigure the repeater.

Q6: What is the effective range of the repeater?

A6: The repeater can extend the Wi-Fi signal up to 100ft (approximately 30 meters) through walls, depending on environmental factors and obstacles. For optimal performance, place the repeater midway between your router and the desired coverage area.

Q7: Can I connect the repeater to my router via an Ethernet cable and then use it to transmit Wi-Fi?

A7: Yes, this is the Access Point (AP) mode. Connect an Ethernet cable from your main router to the repeater's LAN port, then configure the repeater to operate in AP mode via its web management interface.

Q8: Does it work with a 4G router?

A8: Yes, the repeater is compatible with any standard wireless router, including 4G routers, as long as it broadcasts a Wi-Fi signal that the repeater can extend.

Q9: Can I disable DHCP on the repeater?

A9: Yes, the web configuration interface typically provides an option to disable DHCP if you prefer your main router to handle all IP address assignments.

9. User Tips

• Optimal Placement: For best results, place the repeater roughly halfway between your main router and the area where you need improved Wi-Fi coverage. If the signal is still weak, try moving it closer to the router.
• Password Simplicity: When using WPS setup, ensure your router's Wi-Fi password does not contain complex special characters, as some repeaters may have difficulty recognizing them.
• Coverage vs. Speed: Remember that a repeater's primary function is to extend Wi-Fi coverage, not necessarily to increase the maximum internet speed. While it provides a stronger signal, the overall throughput might be slightly reduced due to the half-duplex operation.
• Plug Type: Ensure you select the correct plug type (EU, US, UK) for your region when purchasing.
• Wired Connection: If possible, use the LAN port for wired connections to devices like PCs or gaming consoles for a more stable and potentially faster connection in the extended area.

10. Warranty and Support

For warranty information and technical support, please refer to the seller's official website or contact their customer service directly. Keep your purchase receipt for any warranty claims.