Kllisre X79 Motherboard User Manual

1. Introduction

This manual provides detailed instructions for the installation, setup, operation, and maintenance of your Kllisre X79 Motherboard. Designed to support Intel Xeon LGA 2011 processors and DDR3 ECC RAM, this motherboard offers high compatibility and performance for various usage scenarios including gaming, household, and office applications. Please read this guide thoroughly before proceeding with any installation or configuration.

For a more detailed installation guide, you may refer to the official PDF document: Installation Guide: Intel Motherboard and Processor (PDF).

2. Safety Precautions

Always observe the following safety precautions to prevent damage to components and ensure personal safety:

• Electrostatic Discharge (ESD) Protection:
  • Always use anti-static measures, such as an anti-static wrist strap connected to a grounded object.
  • Touch grounded metal (e.g., the computer case) before handling components.
  • Avoid working on carpeted surfaces.
  • Keep components in anti-static bags until ready for use.
• Handling Components:
  • Never force components into place.
  • Handle components by their edges only; avoid touching contacts or socket pins.
  • Keep your workspace clean and organized.
  • Use proper tools for installation.
• Power Supply: This motherboard requires a powerful power supply. Ensure your power supply is at least 450W (brand power supply recommended) to adequately support the platform.

3. Specifications

Below are the key specifications for the Kllisre X79 Motherboard:

Note: Due to different batches of factory materials (PCB boards, heat sinks, PCI-e and RAM slots, etc.), the appearance and color of the motherboard may vary. The picture is for reference only. This will not affect the use of the product.

4. Setup Guide

This section outlines the steps for installing your Kllisre X79 Motherboard and its components.

4.1. Product Diagram

4.2. Pre-Installation Preparation

Tools Required:

• Anti-static wrist strap
• Thermal paste (if not pre-applied on cooler)
• Screwdriver (usually Phillips #2)
• Flashlight (for better visibility)

Workspace Setup:

1. Choose a clean, well-lit, static-free environment.
2. Use an anti-static mat or work on a non-conductive surface.
3. Wear an anti-static wrist strap connected to a grounded object.
4. Keep all components in anti-static bags until ready for use.

Component Verification:

• Confirm CPU socket compatibility (LGA 2011 for Intel Xeon processors).
• Verify motherboard BIOS supports the CPU model.
• Check RAM compatibility with the motherboard's Qualified Vendor List (QVL).

4.3. CPU Installation

1. Open CPU Socket: Locate the CPU socket on the motherboard. Gently lift the socket lever to the vertical position. Remove the socket cover if present.
2. Align CPU: Identify the triangle marker on the CPU (usually a gold corner). Match this with the triangle marker on the socket. For LGA sockets, the CPU has no pins; pins are in the socket.
3. Place CPU: Hold the CPU by its edges only (avoid touching contacts). Gently lower the CPU into the socket without force. Ensure the CPU sits flat with no gaps.
4. Secure Socket: Carefully lower the socket lever. Press down until it clicks into place. Verify the CPU is securely locked.

Important Notes:

• Never force the CPU into the socket.
• Do not touch CPU contacts or socket pins.
• Handle the CPU by its edges only to prevent damage.

4.4. CPU Cooler Installation

Stock Cooler Installation:

1. Apply Thermal Paste: Apply a pea-sized amount of thermal paste to the center of the CPU. If using pre-applied paste, skip this step.
2. Position Cooler: Align the cooler with the mounting holes. Ensure the retention mechanism matches the socket type.
3. Secure Cooler: Attach clips or screws in a diagonal pattern. Apply even pressure to spread the thermal paste.
4. Connect Fan: Connect the CPU fan cable to the CPU_FAN header on the motherboard. Ensure cable routing does not interfere with other components.

Aftermarket Cooler Installation:

• Follow manufacturer-specific instructions for your aftermarket cooler.
• May require backplate installation.
• Check for clearance with RAM and other components.

4.5. RAM Installation

1. Identify Slots: Refer to the motherboard manual for optimal slot configuration. Usually, start with slot A2 for a single module.
2. Align Notch: Match the RAM module's notch with the slot key. Ensure correct orientation.
3. Insert RAM: Apply firm, even pressure on both ends of the module. The modules should click into place. Verify that the retention clips snap shut.

Configuration Tips:

• For dual-channel configuration, install modules in matching colored slots.
• Check the maximum supported frequency in BIOS.

4.6. Motherboard Mounting

1. Install I/O Shield: Insert the I/O shield into the rear of the case. Ensure proper alignment with the ports.
2. Position Standoffs: Install brass standoffs in the case, matching the motherboard holes. Use only necessary standoffs to avoid shorts.
3. Mount Motherboard: Carefully lower the motherboard onto the standoffs.
4. Secure with Screws: Align I/O ports with the shield and secure the motherboard with screws (do not overtighten).

4.7. Power Connections

Essential Connections:

• 24-pin ATX power: Main motherboard power.
• 8-pin CPU power: CPU VRM power (usually near the CPU socket).
• PCIe power: For graphics card (if applicable).
• SATA power: For storage devices.
• Peripheral power: For additional components.

Connection Tips:

• Connect all required power cables before powering on the system.
• Ensure all connectors are fully seated.
• Verify no loose cables near fans.

5. Operating Instructions

5.1. Post-Installation Checks (First Power-On)

1. Visual Inspection:
   • Verify all components are securely installed.
   • Check for any loose screws or tools inside the case.
   • Ensure cables are clear of moving parts.
   • Confirm all power connectors are attached.
2. First Power-On:
   • Connect a monitor to the graphics card (not directly to the motherboard if a dedicated GPU is installed).
   • Press the power button and observe the system.
   • Listen for POST beep codes (refer to your case/BIOS manual for code meanings).
   • Check that the CPU fan is spinning.
3. BIOS Configuration:
   • Enter BIOS/UEFI setup (usually by pressing Del or F2 key during boot).
   • Verify that the CPU and RAM are detected correctly.
   • Check temperatures and voltages.
   • Enable XMP/DOCP for RAM overclocking if desired.
   • Set the boot order for your operating system drive.

6. Maintenance

Regular maintenance helps ensure the longevity and optimal performance of your motherboard:

• Clean dust from components regularly using compressed air.
• Reapply thermal paste to the CPU every 1-2 years for optimal cooling.
• Update BIOS for better compatibility and performance (refer to manufacturer's website).
• Monitor temperatures during operation to prevent overheating.

7. Troubleshooting

If you encounter issues, consider the following troubleshooting tips:

• No POST (Power-On Self-Test):
  • Check all power connections (24-pin ATX, 8-pin CPU).
  • Verify the CPU is properly seated in its socket.
  • Ensure RAM modules are fully inserted and in the correct slots.
  • Try booting with only essential components (CPU, one RAM stick, GPU if no integrated graphics).
  • Listen for beep codes and consult your BIOS manual for their meaning.
• System Instability/Crashes:
  • Check CPU and GPU temperatures.
  • Ensure all drivers are up to date.
  • Test RAM modules individually.
  • Verify power supply wattage is sufficient for all components.
• General Issues:
  • Consult the motherboard manual for specific error codes or troubleshooting steps.
  • Visit the manufacturer's website for support and updated drivers/BIOS.
  • Check community forums for similar issues and solutions.

8. User Tips

No specific user tips are available from provided reviews or Q&A content at this time. Always ensure compatibility of all components (CPU, RAM, GPU, PSU) before installation.

9. Warranty and Support

Your Kllisre X79 Motherboard comes with a 1-year warranty from the date of purchase. For any issues or support, please refer to the following resources:

• Official User Manual (PDF): Download PDF
• Manufacturer's Website: Visit the Kllisre official website for updated drivers, BIOS, and support information.
• Technical Support: Contact Kllisre technical support if needed.