BAOFENG UV-9R Pro

Contents

Baofeng UV-9R Pro IP68 Waterproof Walkie Talkie User Manual

Model: UV-9R Pro

Brand: BAOFENG

1. Introduction

Thank you for purchasing the Baofeng UV-9R Pro Series Amateur Radio. This dual-band, dual-display, dual-watch radio is designed to provide secure, instant, and reliable communications. Please read this manual carefully to ensure optimal performance and safe operation.

1.1 Important Safety Information & Warnings

WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.

ATTENTION: When programming the radio, always start by reading the factory software data. Then, rewrite this data with your desired frequencies to a new saved code plug. Failure to do so may result in errors. Ensure your programming complies with your FCC (or EU/other country) license certification.

ATTENTION: Before using this product, refer to the RF Energy Exposure and Product Safety Guide provided with the radio. This guide contains instructions for safe usage and RF energy awareness to ensure compliance with applicable standards and regulations.

This manual is applicable to the following products: UV-9R Plus, WP-9R, and AR-9 Radio.

FRS, GMRS, MURS, PMR446 Frequencies

While you may be tempted to use FRS, GMRS, MURS (in the USA) or PMR446 (in Europe) frequencies, please note that there are restrictions on these bands that may make this transceiver illegal for use without proper licensing and compliance.

1.2 Package Contents

Please verify that all items are present in your package. If any item is missing, contact your BAOFENG dealer.

  • 1 x Portable Radio
  • 1 x Antenna
  • 1 x Li-ion Battery
  • 1 x Charger (Fast desktop charger, Wall adaptor)
  • 1 x Belt Clip
  • 1 x Sling
  • 1 x User's Manual
  • Other accessories may be included depending on your specific purchase choice.
Contents of the Baofeng UV-9R Pro package, including the radio, charger, antenna, and user manual.
Figure 1: Typical package contents of the UV-9R Pro.

2. Product Overview

The Baofeng UV-9R Pro is a rugged, waterproof, and dustproof two-way radio designed for various applications, including outdoor activities, construction sites, and general communication.

Baofeng UV-9R Pro walkie talkie in green, highlighting 50KM range, high power, long distance, and IP68 waterproof rating.
Figure 2: Baofeng UV-9R Pro Walkie Talkie.

2.1 Main Features

  • Output Power: High Power (5w-10w)
  • Frequency Range:
    • FM Radio: 76-108 MHz
    • AM Aviation Frequency Band: 108-136MHz (RX)
    • VHF1: 136-174MHz (RX&TX)
    • UHF1: 400-520MHz (RX&TX)
    • UHF2: 350-390MHz (RX)
  • Waterproof / Dustproof: IP68 rated (submersible up to 1 meter for 30 minutes)
  • Channels: 128 memory channels
  • Battery: Li-Ion 4800mAh (Note: User manual PDF states 1800mAh)
  • Display: LCD with backlight adjustable in 3 colors
  • Functions: VOX, Scan, Dual Watch, TOT (Time out timer), Reverse function, CTCSS/DCS codes, Busy Channel Lockout (BCL), Repeater shift, Voice prompt, Power Save, DTMF, Alarm function, Channel/Frequency mode selection, High/Middle/Low power selection, Frequency offset, Squelch adjustable in 9 levels, Keypad lock, 1750Hz tone for repeaters.

2.2 Radio Components and Controls

Diagram of the Baofeng UV-9R Pro radio with labeled components: Antenna, Flashlight, Knob, LED Indicator, Speaker, Mic, Accessory Jack, LCD, PTT, Key1/F, Key2/M, Keypad.
Figure 3: Radio Components and Controls.
  1. Antenna
  2. LED: Red for transmission, Green for reception
  3. Flashlight
  4. SOS: Press and hold for 5 seconds to activate alarm mode
  5. Power / Switch / Volume control: Rotate to turn on/off and adjust volume
  6. Speaker
  7. Microphone
  8. LCD display
  9. EXIT: Press to exit Menu and functions. A/B (on display) selects desired frequency (VHF or UHF)
  10. #: Keypad lock (long press), High/Low power selection (short press)
  11. PTT (Push-to-Talk)
  12. SK1: Short press for FM radio, long press for One touch frequency Search
  13. SK2: Short press for flashlight (strobe mode with second press), long press for Monitor function
  14. ▲/▼ keys: Select functions/menu items
  15. MENU: Enter MENU functions, confirm selection. Long press in off state to switch between frequency/channel mode.
  16. *SCAN: Short press for Reverse function. Long press for SCAN function
  17. MIC/SP: External speaker/microphone jacks
  18. 1800mAh Li-Ion battery pack
  19. Battery release latch

2.3 LCD Display Indications

Close-up of the Baofeng UV-9R Pro LCD display showing frequency, channel, and various icons like CT, DCS, VOX, RN, B, and battery level.
Figure 4: LCD Display with Wave Button Design.
  • DCS or CTCSS code: Indicates active DCS or CTCSS code for TX/RX.
  • Received signal strength.
  • Low power selection.
  • Dual Watch function active.
  • VOX function enabled.
  • Positive shift activated.
  • Negative shift activated.
  • Reverse frequency.
  • Narrow bandwidth (N): No icon for wide bandwidth.
  • Keypad lock.
  • Battery level indicator: Blinks when low, transmission blocked.
  • Channel number.
  • Reception mode icon.
  • Frequency in use, channel name, or menu setting.
  • VFO in use and current menu/function setting.

Status LED Indicator

STATUSLED
No BatteryGreen and red alternately flashing
Charge NormallyRed
Fully ChargedGreen
TroubleRed blinks fast for a long time

Note: "Trouble" indicates battery too warm, short-circuited, or charger short-circuited.

3. Setup

3.1 Charging the Battery

The Li-ion battery pack is not charged at the factory. Please charge it before first use. For optimal performance, fully charge and discharge the battery two or three times.

  • Use only the specified charger provided by Baofeng.
  • Charge the battery in ambient temperatures between 5°C and 40°C (40°F and 105°F).
  • Turn off the radio before charging to prevent interference.
  • Do not interrupt the charging cycle until the green light is on.
  • Do not recharge a fully charged battery.
  • Ensure the battery and radio are dry before charging.
  • It takes approximately 2-5 hours to fully charge the battery.
Baofeng UV-9R Pro radio in its charging cradle.
Figure 5: Radio in charging cradle.

Battery Storage

  • Store the battery at approximately 80% discharged.
  • Keep in a low temperature and dry environment, away from direct sunlight.
  • Do not short circuit battery terminals.
  • Do not disassemble the battery pack.
  • Do not store in unsafe surroundings or hot environments.

3.2 Installing/Removing the Antenna

  • Installing: Screw the antenna clockwise into the connector on top of the transceiver until secure.
  • Removing: Turn the antenna counter-clockwise to remove it.
Comparison of the UV-9R Pro 701 antenna (21cm) and an ordinary antenna (13.5cm), showing the flexibility of the Pro antenna.
Figure 6: UV-9R Pro 701 Antenna vs. Ordinary Antenna.

3.3 Installing the Belt Clip

  • Install the fixing head of the belt clip into the slot on the back of the radio and tighten the screws.
  • Slide the fixed head of the machine along the guide of the rotating back clip until it clicks.
  • To remove, press the disassembly engine upwards and push the belt clip with your thumb.
Diagram showing how to install and remove the belt clip on the radio.
Figure 7: Belt Clip Installation.

3.4 Installing the Battery Pack

Before attaching or removing the battery, ensure the radio is turned off by rotating the power/volume knob counter-clockwise.

  • Insert the two protrusions on the front of the battery into the notches on the bottom of the radio.
  • Press the tail of the battery toward the radio until you hear a "click".
  • To remove, lift the battery push button and disengage the tail of the battery, then remove it backwards.
Close-up of the battery compartment latch on the Baofeng UV-9R Pro.
Figure 8: Battery Compartment Latch.

3.5 Installing Additional Speaker/Microphone (Optional)

  • Use a flat-blade screwdriver to unscrew the screw at the lower end of the cover counter-clockwise to remove the headset cover.
  • Insert the protruding part of the lower end of the headset into the slot.
  • Align the nut on the upper end of the headset with the corresponding threaded hole and rotate it clockwise until tightened.

NOTE: Ensure accessories are installed correctly; otherwise, the waterproof performance of this product may be affected.

4. Operating Instructions

4.1 Power On/Off and Volume Adjustment

  • Power On: Rotate the Volume/Power knob clockwise until you hear a "click". The display will show a message or flash, followed by a frequency or channel.
  • Power Off: Rotate the Volume/Power knob counter-clockwise until you hear a "click".
  • Adjusting Volume: Rotate the Volume/Power knob clockwise to increase volume, counter-clockwise to decrease.

4.2 Making a Call

  • Channel Mode Call: Select a channel, then hold down the [PTT] key. Speak into the microphone with a normal tone. The red LED will illuminate.
  • Frequency Mode Call: In the off state, hold [MENU] to turn on the radio in frequency mode. Enter the desired frequency, then hold down the [PTT] key. Speak into the microphone.
  • Receiving a Call: Release the [PTT] key. The green LED will illuminate when receiving a call.

Note: For best reception, keep the microphone 2.5 cm to 5 cm from your mouth during transmission.

4.3 Channel Selection (VFO vs. MR Mode)

The radio operates in two modes: Frequency (VFO) mode and Channel (MR) mode.

  • Frequency (VFO) Mode: Used for temporary frequency assignments, experimentation, and programming channels into memory. Navigate frequencies using the ▲ and ▼ keys or by direct numeric input.
  • Channel (MR) Mode: More practical for everyday use with pre-programmed channels. Navigate channels using the ▲ and ▼ keys.

WARNING: Transmitting on frequencies for which you are not authorized is illegal and may result in fines or legal penalties. Always comply with local regulations.

4.4 Advanced Features and Menu Operations

The radio offers a comprehensive menu system for advanced configuration. Access the menu by pressing the [MENU] key.

Menu Navigation

  • Press [MENU] to enter.
  • Use ▲/▼ keys to navigate items.
  • Press [MENU] again to select an item.
  • Use ▲/▼ keys to select a parameter.
  • Press [MENU] to confirm and save, or [EXIT] to cancel.
  • Press [EXIT] at any time to exit the menu.

Keypad Shortcuts

Each menu item has a numerical value for direct access. For example, to access Squelch Level (MENU No.0), press [MENU] then '0'.

Key Functions Overview

  • [SOS] key: Long press for alarm function.
  • [SK1] key: Short press for FM radio. Long press for One touch frequency Search.
  • [SK2] key: Short press for flashlight (strobe mode with second press). Long press for Monitor function.
  • [#] key: Short press to switch High/Middle/Low output power. Long press to lock/unlock keypad.
  • [*SCAN] key: Short press for Reverse function. Long press for SCAN function.

Programming Channels (Memory)

The UV-9R Pro supports 128 memory channels. Programming can be done manually or via PC software.

For detailed manual programming steps, refer to the official user manual (PDF) section 6.10 "Manual Programming (Channels Memory)".

Weather Radio/Scan Weather Channel

The radio includes NOAA Weather Radio function. To activate, press [0SQL] for 3 seconds. Press and hold [EXIT] for 3 seconds to start scanning all 10 NOAA channels. Press [*SCAN] for 3 seconds to stop scanning. To exit, press [EXIT] or [PTT].

Channel NumberRX Frequency MHzChannel NumberRX Frequency MHz
Wx-01162.550Wx-06162.500
Wx-02162.400Wx-07162.525
Wx-03162.475Wx-08161.650
Wx-04162.425Wx-09161.775
Wx-05162.450Wx-10163.275

Note: These are Receive-only channels for NOAA and Canadian weather broadcasts. Transmission is not possible on these channels.

Video 1: Baofeng UV-9R Pro Waterproof and Durability Test. The video demonstrates the radio's IP68 waterproof capabilities through immersion tests in a laboratory and outdoor setting, as well as a durability test where a car drives over the radio.

5. Maintenance

5.1 General Care

  • Handle the product with care to prevent damage.
  • Do not disassemble, modify, or repair the product or its accessories without authorization.
  • Keep the product and its accessories out of reach of children and pets.
  • Operate the product within the specified temperature range.
  • Avoid continuous transmission for long periods to prevent overheating. Allow the radio to cool down if it becomes warm.

5.2 Battery Maintenance

  • Regularly clean the charging connector with a clean, dry cloth to prevent dust accumulation.
  • Charge the battery between 5°C and 40°C (40°F and 105°F). Charging outside this range may reduce battery life or cause leakage.
  • Do not dispose of the battery in fire.
  • Do not expose the battery to direct sunlight or place it near other heat sources.

6. Troubleshooting

If you encounter issues with your radio, refer to the table below for common problems and solutions.

PhenomenaAnalysisSolution
Cannot turn on the radio.Battery improperly installed, power low, or dirty contacts.Reattach/replace battery, clean contacts.
Weak or intermittent voice during reception.Low battery, low volume, loose antenna, blocked speaker.Recharge/replace battery, increase volume, reattach antenna, clean speaker.
Cannot communicate with other group members.Inconsistent frequency/signaling, too far away.Verify TX/RX frequency/signaling, move closer.
Hears unknown voices or noise.Interrupted by same frequency radios, analog mode with no signaling.Change frequency/squelch, set signaling.
Unable to hear due to too much noise/hiss.Unfavorable position (blocked by buildings), external interference.Move to open area, restart radio, stay away from interference.
Radio keeps transmitting.VOX turned on, headset not installed.Turn off VOX, check headset.

Note: If these solutions do not resolve your issues, contact your dealer for technical support.

7. Technical Specifications

AttributeSpecification
Model NumberBaofeng UV-9RPLUS (UV-9R Pro)
Output Power (W)5w-10w
Frequency Range136-174Mhz & 400-520Mhz (VHF/UHF)
Memory Channel128 Groups
Operation VoltageDC 7.4 V ±10%
Battery Capacity4800mAh (Li-Ion) (Note: User manual PDF states 1800mAh)
Waterproof / Water-ResistantIP68
MaterialPlastic
Dimensions (Radio Body)135mm (H) x 55mm (W) x 36mm (D) (Note: Product properties state 173*100*95 mm, likely package dimensions)
Transmission Current≤1800mA
Receive Sensitivity0.25µV (12dB SINAD)
Power Output1W @16 ohms
Receive Current≤380mA
Rated Audio Distortion≤5%
FCC ID2AJGM-UV9RPRO
CertificationCE, FCC

ATTENTION: Always comply with the Radio Regulations in your country or territory regarding operating frequencies.

8. User Tips

  • Range Expectations: While advertised with a long range (e.g., 50km), actual communication distance can vary significantly based on terrain, obstacles (buildings, hills), and environmental conditions. Expect shorter ranges (e.g., 5-10km) in urban or rugged environments.
  • Waterproof Caution: The radio is IP68 rated for dust and water resistance (submersible up to 1 meter for 30 minutes). However, some users have reported issues if the device gets wet, so exercise caution and ensure all seals are properly closed before exposure to water.
  • Battery Charging: Some models of the UV-9R Pro battery include a USB-C charging port directly on the battery, offering an alternative charging method to the desktop cradle. Verify your specific battery type.
  • Battery Contact Issues: If the radio turns on and off intermittently, check the battery contacts for proper connection and cleanliness.
  • Programming: For complex frequency programming or channel management, using PC software with a programming cable is generally easier and more efficient than manual programming via the keypad.
  • Accessory Compatibility: Ensure any external accessories like earphones or microphones are compatible with the radio's accessory jack to avoid connection issues.

9. Warranty and Support

9.1 Disclaimer

The Company endeavors to ensure the accuracy and completeness of this manual. However, no warranty of accuracy or reliability is given. All specifications and designs are subject to change without notice due to continuous technological development. No part of this manual may be copied, modified, translated, or distributed without prior written consent of the Company. The Company does not guarantee the accuracy, validity, timeliness, legitimacy, or completeness of third-party products and contents involved in this manual.

9.2 Manufacturer Information

PO FUNG ELECTRONIC (HK) INTERNATIONAL GROUP COMPANY
Address: 3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN, Hong Kong

9.3 Additional Resources

A detailed user manual (PDF) is available for download here.

For further assistance or technical support, please contact your local Baofeng helpdesk or the dealer from whom you purchased this radio.

10. Disposal of Electronic and Electric Equipment

Products marked with the crossed-out wheeled bin symbol cannot be disposed of as household waste. Electronic and Electric Equipment should be recycled at a facility capable of handling these items and their waste products. In EU countries, please contact your local equipment supplier representative or service center for information about the waste collection system in your country.

Crossed-out wheeled bin symbol indicating proper disposal of electronic waste.
Figure 9: Symbol for proper electronic waste disposal.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.