Introduction
The Godox SKIIV series studio flashes, including the SK300IIV and SK400IIV models, are cost-effective and compact strobes designed for e-commerce product shooting, portrait, and lifestyle photography. They are easy to set up in small and medium studios and feature a new brighter LED modeling light.
Key features include a built-in Godox 2.4G wireless X system for synchronous triggering and control, precise output displayed on an LCD panel, a 10W modeling lamp with adjustable power levels, and outstanding output stability.
Video: Godox SK300IIV/SK400IIV Studio Flash Operation Overview
What's in the Box
Please check the contents of your package upon receipt. If anything is missing or damaged, contact your retailer.
- SKIIV Flash Head (x1)
- Power Cable (x1)
- Lamp Cover (x1)
Note: Standard reflector and sync cable are sold separately.

Image: Typical contents for SKIIV series flash.
Setup Guide
1. Mounting the Flash
- Attach the flash head to a compatible light stand. Ensure it is securely fastened.
- The flash features a Bowens mount, allowing for compatibility with a wide range of studio light shapers. Attach your desired light modifier (e.g., reflector, softbox, umbrella) to the Bowens mount on the front of the flash.
2. Connecting Power
- Connect the provided power cable to the power input port on the rear panel of the flash.
- Plug the other end of the power cable into a suitable AC power outlet (AC100V-120V~60Hz or AC200V-240V~50Hz, depending on your model).
3. Initial Power On
- Flip the ON/OFF switch on the rear panel to the 'ON' position. The LCD display will illuminate.

Image: Product details showing Bowens mount and control panel.
Operating Instructions
1. Adjusting Modeling Lamp
The 10W LED modeling lamp can be adjusted from 5% to 100% power levels. Short press the <MOD/OFF> button to cycle through the modeling lamp modes:
- OFF: Modeling lamp is off.
- PROP: Modeling lamp power changes proportionally with the flash power output.
- Percentage (%): Modeling lamp is in adjustable state. Short press the <SET> button to enter the adjustment interface, then rotate the dial to adjust brightness from 5% to 100%. Short press <SET> again to exit.
When the modeling lamp is on, long press <MOD/OFF> for 2 seconds to enable the auto-extinguish function when the flash fires. Long press again to disable this function.

Image: Modeling lamp adjustment from 5% to 100% power levels.
2. Adjusting Flash Power Output
The flash output is precisely displayed on the LCD panel, offering 40 steps from 1/16 to 1/1 (or 6.0 to 10.0). Rotate the main dial to increase or decrease the flash power output.
3. Wireless Control (2.4G X System)
The flash has a built-in Godox 2.4G wireless X system. To achieve wireless synchronous triggering and control, use optional Godox X2, XPro, or XT16 flash triggers.
- Simultaneously press the <GR/CH> (Group/Channel) button and the <S1/S2> (Optical Control Mode) button to activate the built-in 2.4G wireless transmission mode.
- With an X2/XPro trigger, you can also adjust flash settings via the Godox Flash APP on your smartphone.

Image: Wireless X System setup with external trigger and app.
4. Optical Triggering (S1/S2 Modes)
The flash supports optical triggering modes S1 and S2:
- S1 Mode: Functions as a secondary flash. It will fire simultaneously when the main flash fires.
- S2 Mode: Features an anti-preflash function, enabling synchronization with cameras that have a one-preflash firing system. The flash will ignore the preflash from the main flash and fire on the second flash.
5. Test Button
Press the <TEST> button to manually fire the flash and check its output.
6. Auto Memory and Recovery
The flash features auto memory and recovery of adjusted panel settings, ensuring your last used settings are retained when the unit is powered off and on again.
Maintenance
Proper maintenance ensures the longevity and optimal performance of your studio flash.
- Cleaning: Use a soft, dry cloth to clean the exterior of the flash. For stubborn dirt, a slightly damp cloth can be used, followed by immediate drying. Do not use harsh chemicals or abrasive cleaners.
- Storage: Store the flash in a cool, dry place away from direct sunlight and excessive humidity. Always attach the lamp cover when not in use to protect the flash tube and modeling lamp.
- Fuse Replacement: The flash uses a F5AL 250V fuse. If the flash does not power on or function correctly, check the fuse located near the power input. Replace it with a fuse of the same type and rating if necessary.
- Handling: Avoid dropping the flash or subjecting it to strong impacts. Handle the flash tube and modeling lamp with care, avoiding direct contact with bare hands to prevent oil residue.
Troubleshooting
If you encounter issues with your Godox SKIIV series flash, refer to the following common problems and solutions:
- Flash does not power on:
- Ensure the power cable is securely connected to both the flash and the power outlet.
- Check the power outlet for functionality.
- Inspect the fuse (F5AL 250V) on the rear panel and replace if blown.
- Flash does not fire:
- Verify the flash is powered on and the power output is set above minimum.
- If using wireless triggering, ensure the trigger and flash are set to the same group and channel, and the flash is in 2.4G wireless transmission mode.
- If using optical triggering (S1/S2), ensure the flash is in the correct mode and receiving light from the main flash.
- Press the <TEST> button to check if the flash fires manually.
- Modeling lamp not working:
- Check the modeling lamp mode (OFF, PROP, Percentage) and adjust as needed.
- Ensure the brightness level is not set to 0% if in Percentage mode.
- Inconsistent flash output:
- Allow sufficient recycle time between flashes, especially at higher power settings.
- Ensure the flash is not overheating. If the overheat protection activates, allow the unit to cool down.
Specifications
| Feature | SK300IIV | SK400IIV |
|---|---|---|
| Max Power | 300Ws | 400Ws |
| Guide Number (m ISO 100) | 58 | 58 |
| Operating Voltage | AC100V-120V~60Hz or AC200V-240V~50Hz | |
| Power Output Control | OFF, 6.0-10.0 (1/16-1/1) | |
| Modeling Lamp (W) | 10W | |
| Modeling Lamp Level | 5%-100% | |
| LED Modeling Lamp CCT | 5700K±200K | |
| Recycle Time | 0.1-1.5S | |
| Triggering Method | Sync cord, Optical triggering, Test button, Wireless control port | |
| Flash Duration | 1/2000-1/800s | |
| Parameters output from USB port | 5V/200mA (only for Godox receiver) | |
| Fuse | AC100V-120V~60Hz: 8A, AC200V-240V~50Hz: 5A | |
| Dimension (Flash diameter) | Ø13.7cm | |
| Dimension (Height with handle) | 20.6cm | 23.2cm |
| Dimension (Length with lamp cover) | 35cm | 39cm |
| Net Weight | Approx. 2kg | Approx. 2.1kg |
| Compatible Brands | Lumix, FUJIFILM, Pentax, Sony, Canon, NIKON, Olympus | |
| Certification | CE | |
Image: Technical specifications table for Godox SK300IIV and SK400IIV.

User Tips
- Experiment with Modifiers: The Bowens mount offers great versatility. Experiment with different softboxes, beauty dishes, and reflectors to achieve various lighting effects for your subjects.
- Utilize Wireless Control: For optimal workflow and creative flexibility, invest in a compatible Godox X-system trigger (X1, X2, XPro, or XT16). This allows for remote power adjustments and triggering, especially useful when the flash is in hard-to-reach positions.
- Modeling Lamp for Pre-visualization: Use the modeling lamp to pre-visualize your lighting setup before firing the flash. Adjust its brightness to match your ambient light or desired effect.
- Power Management: While the flash has auto memory, it's good practice to note down your preferred power settings for specific setups to quickly recreate them in future shoots.
Warranty and Support
Godox products are designed for reliability and performance. For warranty information, please refer to the documentation provided with your purchase or contact your local Godox distributor. For technical support or service inquiries, please visit the official Godox website or contact their customer service department.