MicroZone MC6RE, MC7RB, MC9002, M-SBUS, MC8RE

Contents

MicroZone RC Receiver Instruction Manual

Models: MC6RE, MC7RB, MC9002, M-SBUS, MC8RE

1. Introduction

This manual provides essential information for the proper setup, operation, and maintenance of your MicroZone RC receivers. Please read this manual thoroughly before using your receiver to ensure safe and optimal performance. These receivers are designed for use with various RC models, including airplanes and drones, and are compatible with specific MicroZone transmitters.

Assortment of MicroZone RC receivers including MC6RE, MC7RB, MC9002, M-SBUS, and others

Figure 1: Various MicroZone RC Receiver Models

2. Transmitter & Receiver Compatibility

Ensure your receiver is compatible with your MicroZone transmitter. Refer to the compatibility table below for details.

Compatibility table showing MicroZone receivers (MC7RB, MC6RE, E6R-E, MC9002, MC8RE, E7R, E7-GPS, MC9008S, 6C Mini SBUS, 8C Mini SBUS) and their compatibility with transmitters (MC6C, E6, MC7, MC8B, MC10, E7, E7S). A checkmark indicates compatibility, an orange dot indicates partial or specific compatibility.

Figure 2: Comparison Table of Transmitter & Receiver Compatibility

Note: A checkmark (✓) indicates full compatibility. An orange dot (•) indicates specific or partial compatibility, please consult your transmitter's manual for further details on these pairings.

3. Specifications

Detailed specifications for each receiver model are provided below.

3.1. MC6RE Mini Receiver

MicroZone MC6RE Mini 6-channel receiver with specifications table

Figure 3: MC6RE Mini Receiver

FeatureSpecification
Size37 x 23 x 13 mm
Weight8g
Antenna Length110mm
Output Channels6 PWM, 1 SBUS
Receiving Frequency2401MHz-2479MHz
Receiving DistanceAir distance > 800M
Voltage RangeDC 3.5V-7.4V
Frequency MatchingContact frequency
Applicable TransmitterMC6C

3.2. MC7RB Receiver

MicroZone MC7RB built-in antenna receiver with specifications table

Figure 4: MC7RB Receiver

FeatureSpecification
ModelMC7RB
Size42 x 28 x 13 mm
Weight9g
Antenna LengthBuilt-in antenna design
Output Channels7 PWM, 1 SBUS
Receiving Frequency2401MHz-2479MHz
Receiving DistanceAir distance > 800M
Voltage RangeDC 3.5V-7.4V
Decoding Way1024 PPM/PCMS
System2.4G S-FHSS
Frequency MatchingContact frequency

3.3. MC8RE Receiver

MicroZone MC8RE 8-channel receiver with specifications table

Figure 5: MC8RE Receiver

FeatureSpecification
Product NameMC8RE
Size42 x 28 x 12 mm
Weight12g
Antenna Length110mm
Output Channels8 PWM, 1 SBUS
Receiving Frequency2401MHz-2479MHZ
Voltage RangeDC 2V-9V
Frequency MatchingContact pair frequency
Applicable TransmittersMC7, MC8B, MC10, E7, E7S
ApplicationFixed wing models, UAV, helicopter models, trams, tanker models, ship models

3.4. MC9002 Receiver PWM/SBUS

MicroZone MC9002 8CH+M.BUS receiver with specifications table

Figure 6: MC9002 Receiver

FeatureSpecification
Size47 x 25 x 14 mm
Weight10g
Antenna Length150mm (Dual antenna design)
Output Channels8 PWM, 1 SBUS
Receiving DistanceAir distance > 1000M
Receiving Frequency2.4GHz
Voltage RangeDC 4V-9V
Frequency MatchingContact frequency matching

3.5. MC9008S Receiver

MicroZone MC9008S receiver with specifications

Figure 7: MC9008S Receiver

FeatureSpecification
ModelMC9008S
Size47 x 25 x 14 mm
Weight10g
Output Channel Resolution2048 resolution
OutputM.BUS (compatible with S.BUS)
Receiving Frequency Band2.4GHz
Working Voltage4V to 9V
AntennaDual antennas for stronger sensitivity
ProtectionSupport out of control protection
Frequency MethodContact frequency
Applicable TransmitterMC10

3.6. Mini M-SBUS Receiver (for MC6C)

MicroZone Mini M-BUS (6C) receiver with specifications table

Figure 8: Mini M-SBUS Receiver

FeatureSpecification
Product NameMini MSBUS receiver
Size21 x 8 x 2 mm
Weight2g
Antenna Length27mm
Output Channels1 SBUS (DuPont connector)
Receiving Frequency2401MHz-2479MHZ
Voltage RangeDC 3.5V-7.4V
Frequency MatchingContact pair frequency
ApplicationTraversing machine, DIY small UAV
Applicable TransmitterMC6C

4. Setup and Binding

Before operating your RC model, the receiver must be properly connected and bound to your compatible MicroZone transmitter.

4.1. Connections

Connect the receiver to your flight controller or servos according to your model's wiring diagram. Ensure correct polarity for power connections. PWM channels are typically connected directly to servos, while SBUS outputs connect to flight controllers that support SBUS input.

MicroZone MC-GPS and E7R Stabilize Receiver connected, showing wiring

Figure 9: Example Receiver Connections (MC-GPS and E7R shown)

4.2. Binding Procedure (Frequency Matching)

The binding process, also referred to as 'contact frequency' or 'electric shock frequency', establishes a secure communication link between your transmitter and receiver. The exact steps may vary slightly by transmitter model, but generally involve:

  1. Ensure both the transmitter and receiver are powered off.
  2. Connect a bind plug (if required by your receiver model) to the 'BIND' port on the receiver.
  3. Power on the receiver. The LED indicator on the receiver should start flashing, indicating it is in bind mode.
  4. While holding the bind button on your transmitter (if applicable), power on the transmitter.
  5. Observe the receiver's LED. Once binding is successful, the LED should turn solid or flash in a different pattern (refer to your specific receiver's LED indicator guide).
  6. Power off both the receiver and transmitter.
  7. Remove the bind plug from the receiver.
  8. Power on the transmitter first, then the receiver. Verify that the receiver's LED is solid, indicating a successful connection. Test control surfaces or motor response carefully.

For models like the MC9008S, which feature dual antennas, ensure both antennas are positioned optimally for signal reception, typically at 90-degree angles to each other, away from carbon fiber or metal components.

5. Operation

Once successfully bound, your receiver will relay control signals from your transmitter to your RC model. Always perform a range check before flying or operating your model to ensure a stable connection.

  • Pre-flight Check: Before each use, verify that all control surfaces respond correctly to transmitter inputs and that the receiver's LED indicates a stable link.
  • Signal Loss Protection: Some receivers support 'out of control protection' (failsafe). Configure this feature on your transmitter to ensure your model reacts predictably in case of signal loss (e.g., motors off, control surfaces neutral).
  • Voltage Monitoring: Pay attention to the receiver's voltage range. Operating outside this range can lead to performance issues or damage.

Video 1: MicroZone Receiver Product Overview

6. Maintenance

To ensure the longevity and reliable performance of your MicroZone receiver:

  • Keep the receiver clean and free from dust, dirt, and moisture.
  • Avoid exposing the receiver to extreme temperatures or direct sunlight for prolonged periods.
  • Regularly inspect antenna wires for any damage or kinks. Ensure they are securely attached.
  • Store the receiver in a dry, cool place when not in use.

7. Troubleshooting

If you encounter issues with your MicroZone receiver, consider the following common troubleshooting steps:

  • No Link/Binding Failure:
    • Ensure both transmitter and receiver are fully charged.
    • Verify the binding procedure is followed correctly (refer to Section 4.2).
    • Check for interference from other 2.4GHz devices.
    • Confirm receiver compatibility with your transmitter (refer to Section 2).
  • Intermittent Signal/Short Range:
    • Inspect antenna placement and condition. Ensure antennas are not obstructed by carbon fiber or metal.
    • Check for loose connections or damaged wiring.
    • Ensure the receiver is not too close to high-current components (ESCs, motors) that can generate electrical noise.
  • Incorrect Control Response:
    • Verify correct channel mapping on your transmitter and flight controller.
    • Ensure servos are connected to the correct PWM ports.

If problems persist, consult your transmitter's manual or seek assistance from experienced RC enthusiasts or the seller.

8. User Tips

  • For optimal signal reception, especially with dual-antenna receivers like the MC9008S, position the antennas at a 90-degree angle to each other. This helps minimize signal loss due to orientation.
  • Always perform a thorough range check before the first flight of a new setup or after any significant changes to your RC model.
  • Consider using a voltage alarm if your model does not have built-in telemetry to monitor receiver voltage and prevent unexpected power loss.

9. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the seller or manufacturer directly. Keep your purchase records for any warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.