1. Introduction
Thank you for choosing the ANDELI CUT-50Y PRO X, a professional 220V multi-function machine combining MMA (Manual Metal Arc) welding and Plasma Cutting capabilities. This unit features a convenient built-in air pump, eliminating the need for an external compressor for most cutting tasks, and utilizes a non-HF pilot arc for non-contact metal cutting. This manual provides essential information for safe operation, setup, maintenance, and troubleshooting to ensure optimal performance and longevity of your equipment.

Figure 1: ANDELI CUT-50Y PRO X Plasma Cutter and MMA Welder
2. Safety Information
WARNING: Welding and plasma cutting can be dangerous. Always follow safety precautions to prevent injury or death.
- Eye Protection: Always wear a welding helmet with appropriate shade lenses to protect your eyes from intense light and UV/IR radiation.
- Body Protection: Wear flame-resistant clothing, gloves, and sturdy shoes to protect against sparks, heat, and electric shock.
- Ventilation: Ensure adequate ventilation to remove fumes and gases produced during welding and cutting.
- Electrical Safety: Ensure the machine is properly grounded. Do not operate in wet conditions. Inspect cables and connections for damage before each use.
- Fire Hazards: Keep flammable materials away from the work area. Have a fire extinguisher readily available.
- Compressed Air Safety: If using an external air compressor, ensure it is properly maintained and operated according to its manual.
- Work Area: Keep the work area clean and free of clutter. Ensure stable footing.
3. Package Contents
Upon unpacking, please verify that all items listed below are included and in good condition:
- ANDELI CUT-50Y PRO X Main Unit
- Ground Clamp (2 meters)
- Cutting Torch (6 meters)
- Gas Pipe (3 meters)
- Oil-water Separator
- Electrode (10 pieces)
- Tip (10 pieces)

Figure 2: Main unit and included accessories
4. Product Overview
4.1 Control Panel Introduction

Figure 3: Front Panel Features
- Gas Meter: Displays the output value of air pressure during cutting.
- Function Key: Switch between CUT (Plasma Cutting) and MMA (Manual Metal Arc) welding functions.
- Air Supply Method Selector:
INT: Use the built-in air pump.
EXT: Do not use the built-in air pump; connect and use an external air pump. - Digital Display: Shows current settings and electrode sizes (for MMA).
- Adjustment Knob: Used to adjust current and other parameters.
4.2 Torch Connection

Figure 4: Torch and Ground Clamp Connections
- CUT Function: The cutting torch is connected to interface ⒈, and the ground clamp is connected to interface ⒊.
- MMA Function: The MMA holder is connected to interface ⒉, and the ground clamp is connected to interface ⒊. This CUT-50Y PRO X also supports MMA reverse connection: the MMA holder is connected to interface ⒊, and the ground clamp is connected to interface ⒉.
4.3 Non-HF Cut Torch Components

Figure 5: Exploded view of the Non-HF Cut Torch
The cutting torch consists of the Cutting Torch Body, Electrode, Swirl Ring, Nozzle, and Nozzle Retaining Cap. These components are crucial for effective plasma cutting and should be inspected regularly for wear.
5. Setup
- Power Connection: Connect the machine to a stable 220V AC power supply. Ensure the power outlet is properly grounded and can handle the machine's input current (up to 38A for CUT, 30A for MMA).
- Install Oil-Water Separator: Attach the oil-water separator to the designated air inlet to ensure clean, dry air supply to the torch.
- Connect Ground Clamp: Securely connect the ground clamp cable to the appropriate interface (⒊ for both CUT and MMA) on the front panel. Attach the ground clamp to the workpiece, ensuring good electrical contact.
- Connect Torch:
- For Plasma Cutting: Connect the cutting torch to interface ⒈.
- For MMA Welding: Connect the MMA electrode holder to interface ⒉ (or ⒊ for reverse polarity).
- Air Supply Selection:
- Built-in Air Pump (INT): If using the internal air pump, set the air supply method selector to 'INT'.
- External Air Pump (EXT): If using an external air compressor, connect the gas pipe from your compressor to the machine's air inlet and set the air supply method selector to 'EXT'. Ensure the external compressor can provide sufficient pressure (e.g., 0.4-0.5 MPa).
- Initial Check: Before powering on, double-check all connections for security and proper polarity.
6. Operating Instructions
6.1 Plasma Cutting Operation
The CUT-50Y PRO X offers efficient plasma cutting with a non-HF start to minimize interference with other electronics.

Figure 6: Cutting thickness examples (5mm, 10mm, 15mm)
- Power On: Turn on the main power switch.
- Select CUT Function: Press the function key to select 'CUT'.
- Set Air Supply: Choose 'INT' for the built-in air pump or 'EXT' for an external air compressor.
- Adjust Cutting Current: Use the adjustment knob to set the desired cutting current. The digital display will show the current value.
- Check Air Pressure: Monitor the gas meter to ensure adequate air pressure for cutting. Recommended pressure for 1-15mm cutting is 0.4 MPa, and up to 20mm cutting requires 0.5 MPa (with stable power supply).
- Start Cutting: Position the torch nozzle close to the workpiece (non-contact start). Press the torch trigger to initiate the pilot arc and then the main cutting arc. Move the torch steadily along the cutting line.
- Cutting Capacity: The machine can easily cut 1-15mm thickness. Under stable power conditions, it can cut up to 20mm.
6.2 MMA Welding Operation
- Power On: Turn on the main power switch.
- Select MMA Function: Press the function key to select 'MMA'.
- Connect Electrode Holder: Ensure the MMA electrode holder and ground clamp are correctly connected (refer to Section 4.2).
- Insert Electrode: Insert the appropriate size electrode into the holder. The digital display indicates compatible electrode sizes (e.g., Ø2.0, Ø2.5, Ø3.2, Ø4.0).
- Adjust Welding Current: Use the adjustment knob to set the desired welding current based on the electrode size and material thickness.
- Start Welding: Strike the arc by lightly touching and then lifting the electrode from the workpiece. Maintain a consistent arc length and travel speed.
7. Maintenance
Regular maintenance ensures the longevity and safe operation of your ANDELI CUT-50Y PRO X.
- Cleaning: Regularly clean the machine's exterior with a dry cloth. Use compressed air to blow out dust from the internal components, especially the cooling vents, to prevent overheating.
- Torch and Consumables: Inspect the cutting torch and MMA electrode holder regularly. Replace worn electrodes, nozzles, swirl rings, and tips as needed.
- Air Filter: Check and clean or replace the filter in the oil-water separator periodically to ensure a clean air supply.
- Cable Inspection: Inspect all cables (power, ground, torch) for cuts, abrasions, or loose connections. Replace damaged cables immediately.
- Storage: Store the machine in a clean, dry environment when not in use.
8. Troubleshooting
This section addresses common issues you might encounter. For problems not listed here, please contact customer support.
- No Power: Check the power cable connection, main power switch, and circuit breaker. Ensure the input voltage is 220V.
- No Arc (Plasma): Ensure the ground clamp has good contact with the workpiece. Check torch consumables for wear. Verify air pressure is sufficient.
- Poor Cut Quality: Adjust cutting speed, current, and air pressure. Ensure consumables are not worn. Check for proper torch standoff distance.
- No Arc (MMA): Ensure the electrode is properly inserted and the ground clamp has good contact. Check welding current settings.
- Overheating: If the machine stops due to overheating, allow it to cool down. Ensure cooling vents are clear and the duty cycle is not exceeded.
9. Specifications

Figure 7: Technical Specifications
| Parameter | MMA | CUT |
|---|---|---|
| Function | MMA | CUT |
| Power Supply Voltage(V) | AC220±15% | |
| Frequency(Hz) | 50/60 | |
| Power Factor | 0.76 | |
| Efficiency(%) | 80 | |
| Rated Output Power(KW) | 4.3 | 7 |
| Rated Input Power(KW) | 5 | 8.5 |
| Rated Input Current(A) | 30 | 38 |
| Effective Input Current(A) | 19.5 | 25.5 |
| Welding Current Range(A) | 20-170 | 15-45 |
| No-Load Voltage(V) | 70 | 320 |
| Duty cycle (% 40°C 10min) | ||
| 40% | 165 | 45 |
| 60% | 134 | 36 |
| 100% | 104 | 28 |
| Welding/Cutting Thickness | / | 25mm |
| Protection Class | IP21S | |
| Insulation Class | H | |
| Cooling | Air cooling | |
| Dimension(MM) | 430x175x265 | |
| Net Weight(KG) | 13 | |
10. User Tips
While no specific user reviews or Q&A were available, here are some general tips for optimizing your experience with the ANDELI CUT-50Y PRO X:
- Practice Makes Perfect: If new to plasma cutting or MMA welding, practice on scrap materials to get a feel for the machine and achieve desired results.
- Consumable Life: The life of your torch consumables (electrodes, nozzles) is directly related to proper use and maintenance. Avoid dragging the torch, and replace consumables when they show signs of wear for optimal cut quality.
- Air Quality: Even with the built-in air pump, ensuring the air is as dry and oil-free as possible will extend consumable life and improve cut quality. Regularly check and maintain the oil-water separator.
- Duty Cycle Awareness: Pay attention to the machine's duty cycle. Exceeding it can lead to overheating and premature wear. Allow the machine to cool down if the thermal overload indicator activates.
11. Warranty and Support
ANDELI products are manufactured to high-quality standards. For warranty information, technical support, or service inquiries, please contact your authorized dealer or the manufacturer directly. Keep your purchase receipt as proof of purchase for any warranty claims.