MOES BS-FB-V3

Contents

Moes Tuya Fingerbot Plus Smart Bluetooth Button Pusher

Model: BS-FB-V3

Brand: MOES

FCC ID: 2A2X5-ADFB0301

1. Introduction

Fingerbot is the world's smallest robot for smartly controlling different types of buttons and switches. It can control your existing home appliances with robotic clicks. Switch lights via App, schedule a morning coffee, activate your vacuum cleaner with voice command, and remotely power on your office PC. Now all these become effortless with Fingerbot.

Fingerbot attached to a light switch, with a smartphone displaying the app interface. Shows 'WORKS WITH alexa' and 'WORKS WITH Google Assistant'.
The Fingerbot Plus attached to a light switch, demonstrating app and voice control compatibility.
Fingerbot Plus on a light switch, being manually pressed.
The Fingerbot Plus features a touch panel for manual operation.

2. Important Safety Information

Read Before Use

This document contains important technical and safety information about the device, its safe use and installation. CAUTION! Before beginning the installation, please read carefully and entirely this guide and any other documents accompanying the device.

Failure to follow the installation procedures could lead to malfunction, danger to your health and life, violation of law or refusal of legal and/or commercial guarantee (if any). MOES is not responsible for any loss or damage in case of incorrect installation or improper operation of this device due to failure of following the user and safety instructions in this guide.

General Warnings

  • Do not disassemble, reassemble, modify or attempt to repair this product by yourself. This work should be performed by authorized professionals.
  • The product is non-waterproof. Do not install it on an underwater appliance.
  • The product contains a lithium battery, therefore prohibited in humid, high-temperature environments.
  • Do not hinder the movement of the Fingerbot's arm when it is working. Otherwise it may cause the arm to fall off and damage to the motor inside Fingerbot.

Battery Safety Warnings

Warning symbol for button cell battery ingestion hazard.

INGESTION HAZARD: This product contains a button cell or coin battery.

  • DEATH or serious injury can occur if ingested.
  • A swallowed button cell or coin battery can cause Internal Chemical Burns in as little as 2 hours.
  • KEEP new and used batteries OUT OF REACH of CHILDREN.
  • Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body.
  • Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. Do NOT dispose of batteries in household trash or incinerate.
  • Even used batteries may cause severe injury or death.
  • Call a local poison control center for treatment information.
  • The battery type: CR2.
  • The battery voltage: 3V.
  • Non-rechargeable batteries are not to be recharged.
  • Do not force discharge, recharge, disassemble, heat above 60°C or incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in chemical burns.
  • Ensure that the battery is correctly loaded into the battery compartment according to the polarity marked, and the positive and negative poles cannot be installed reversely.
  • Do not mix old and new batteries, different brands or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries.
  • Remove and immediately recycle or dispose of batteries from equipment not used for an extended period of time according to local regulations.
  • Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.

3. Setup

3.1. Power Supply

To open the device, open the case from the back and remove the insulating tab of the battery before use.

Diagram showing how to open the Fingerbot case to remove the insulating tab of the battery.
Remove the battery insulating tab before first use.

3.2. Device Installation

  1. Clean the surface of the button or switch panel where you want to install Fingerbot.
  2. Attach Fingerbot to the panel using the double-sided tape provided in the Fingerbot package.
  3. Connect your Fingerbot with the App and calibrate the movement of Fingerbot's robotic arm to fit your switches and buttons.

After installation, we recommend resting Fingerbot for 24 hours to reach maximum adhesion.

3.3. Robotic Arm Extension

With the modular design, the arm of Fingerbot is replaceable in order to meet different needs in diverse situations. The ToolPack is not included in the package with the Fingerbot Plus; it needs to be purchased separately from MOES.

Diagram showing modular design with various tool arms and dimensions (34mm/1.339in cube).
Modular design allows for various tool arms to fit different use cases.
Detailed diagram of various tool arms with dimensions.
Various tool arms are available for different switch types (sold separately).

3.3.1. Straight Arm Installation

You can install the straight arm by following the picture below. We provide three straight arms with different lengths to assist Fingerbot better fitting various button-control cases.

Diagram showing how to install a straight arm onto the Fingerbot.
Installation of the straight arm.

3.3.2. Rocker Arm Installation

Fingerbot makes use of the rocker arm to push and pull the switch button to change the switch status of equipment. Please follow the instructions below to install the rocker arm.

  1. After connecting Fingerbot with the App, set Fingerbot to the 'Switch' mode.
  2. Move the arm of Fingerbot to the bottom and fix the Fingerbot on the switch panel.
  3. Tear off the tape covering on the rocker arm to stick the arm to the switch button.
  4. After ensuring the firmness, use the App to adjust the rising range of Fingerbot's arm, so that its movement range can be adapted to the switch button.
  5. If the app is showing the opposite status to the actual status, please use the 'invert' function to invert the display mode.
Diagram showing how to install a rocker arm onto the Fingerbot and switch.
Installation of the rocker arm for toggle switches.

3.3.3. Ring Arm Installation

Fingerbot makes use of the ring arm to push and pull the toggle switch to change the switch status of equipment. Please follow the instructions below to install the ring arm.

  1. After connecting Fingerbot with the App, set Fingerbot to the 'Switch' mode.
  2. Following the picture, fix two cushion blocks to Fingerbot with tape.
  3. Put the ring of the arm on the toggle button, and tear off the tape covering on the other side of the cushion block to fix the Fingerbot on the switch panel.
  4. After ensuring the firmness, use the App to adjust the movement range of Fingerbot's arm, so that its movement range can be adapted to the toggle.
Diagram showing how to install a ring arm onto the Fingerbot and toggle switch.
Installation of the ring arm for toggle switches.

3.4. App Preparation and Connection

The Moes application is much more compatible than Tuya Smart / Smart Life application. It also provides a new customized service for controlling scenes through Siri, widgets and scene recommendation. (Note: Tuya Smart / Smart Life app is still working, but Moes app is highly recommended)

  1. Download the MOES App from the App Store or Google Play, or scan the QR code below.
  2. QR code for MOES App download and Google Play/App Store buttons.
    Scan to download the MOES App.
  3. Register or Log in to your MOES account.
  4. Ensure your phone's Bluetooth is turned on.
  5. Confirm the blue light on the Fingerbot is flashing. If not, press and hold the reset/function button until a prompt tone is heard and the blue light starts slow flashing, indicating the device has entered distribution network state.
  6. Open the MOES App, click "+" and select "Add Device". The prompt page will automatically show on the screen. Click "Add".
  7. Once the device is added successfully, you can edit its name and click "Done" to enter the device page.

4. Operating Instructions

4.1. App Control

You can control Fingerbot directly via Bluetooth with the App. Up and down movement is optional with 0-100 adjustable to meet your own demand on concrete devices; even featured as sustain time set for added convenience.

Fingerbot controlling a coffee maker via smartphone app.
Control your appliances like a coffee maker via the Tuya Smart App.
Screenshot of the app showing 'Sustain Time' setting, with an example of a coffee machine.
Set the sustain time for precise control in the app.
Image of a child near a fan, with a smartphone app showing 'Touch Control' disabled.
Disable touch control in the app to prevent accidental operations.

4.2. Scheduling

You can set schedulers in the App to automatically activate Fingerbot at certain times. Timer your own schedule for specific devices to turn on/off at a preset time in App.

Fingerbot on a traditional curtain switch, with a smartphone app showing 'Add Schedule'.
Schedule automatic ON/OFF times for your devices. A Bluetooth hub is required for timing schedules.

4.3. Remote Control (Requires Bluetooth Hub)

With a Fingerbot Bridge (needs to be purchased separately), you can control your Fingerbot through the Internet from anywhere.

Diagram illustrating when a Bluetooth hub is required for remote control.
A Bluetooth hub is required for wireless remote control when you are not at home.

4.4. Voice Control (Requires Bluetooth Hub)

With a Fingerbot Bridge, you can connect Fingerbot with voice assistants such as Google Home Assistant and Amazon Alexa. You can set up voice commands in the App to activate voice-control function.

Fingerbot being used with voice commands (Alexa, Google Home) to control a robot vacuum.
Control your appliances with voice commands via Alexa or Google Home.

4.5. Group Control and Sharing

You can create groups in the App to manage all the Fingerbot Plus devices in your house and share the device with your family members.

Diagram showing 'Multiple people control one' and 'One person controls more than one' Fingerbot.
Manage multiple Fingerbots and share control with family members.

4.6. Product Demonstration Video

Video demonstrating the Fingerbot controlling a water dispenser and a lamp.

5. Maintenance

5.1. Battery Replacement

The Fingerbot uses a CR2 battery (3V). When the battery is low, replace it with a new one. Ensure correct polarity during installation.

5.2. Recycling Information

All products marked with the symbol for separate collection of waste electrical and electronic equipment (WEEE Directive 2012/19/EU) must be disposed of separately from unsorted municipal waste. To protect your health and the environment, this equipment must be disposed of at designated collection points for electrical and electronic equipment designated by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences for the environment and human health. To find out where these collection points are and how they work, contact the installer or your local authority.

6. Troubleshooting

If you have problems installing or operating your device, please review its product data sheet: https://www.moestech.com/blogs/news/bs-fb-v3

  • Device not pairing: Ensure Bluetooth is enabled on your phone and the Fingerbot's blue light is flashing. If not, long-press the reset button for 5 seconds to enter pairing mode.
  • Remote control not working: A Bluetooth gateway (hub) is required for remote control when you are not within Bluetooth range (approx. 10 meters).
  • Voice control not working: A Bluetooth gateway (hub) is required for voice control via Alexa or Google Home.
  • Fingerbot not adhering: Ensure the surface is clean and dry before applying the 3M sticker. Allow 24 hours for maximum adhesion after installation.
  • Arm movement issues: Calibrate the movement range in the app to fit your specific switch or button.
  • App showing opposite status: Use the 'invert' function in the app to correct the display mode.

7. Specifications

Feature Detail
Model BS-FB-V3
Dimensions 34.5 x 34.5 x 34.5 mm
Weight 38g
Communication Protocol BLE 4.2
Functionalities App Control, Voice Control, Cloud Control, Scheduler
Stall Torque 2.0 kgf·cm (Updated to 9N→15N for Plus version)
Working Temperature -10 ~ 55℃ / 14 °F ~ 131 °F
Battery Capacity 500 mAh (Updated to 800mAh for Plus version)
Battery Type CR2
Frequency Band 2.4GHz
Maximum Radio Transmit Power +4dbm
Maximum Arm Movement 12 mm
Clicking Life 15K Clicks
Material Plastic
Certifications CCC, CE, FCC ID: 2A2X5-ADFB0301
Radar chart comparing Fingerbot Plus vs. Fingerbot, showing updates in Clicking life, Movement range, Force, and Battery capacity.
Comparison of Fingerbot Plus features with previous version.

8. Warranty and Support

8.1. Warranty Instructions

Products are covered by a 24-month warranty, effective from the date of purchase of the covered product by a retail customer.

To exercise warranty rights, the purchaser must present: a) Warranty card, b) Proof of purchase (VAT invoice, financial receipt or other document confirming the actual date of purchase), unless the purchase date of the product comes from the warranty card.

If product quality problems occur within 24 months from the date of receipt, please prepare the product and packaging and go to the place or store where you purchased it to apply for after-sales maintenance. If the product is damaged due to personal reasons, a certain maintenance fee will be charged.

The warranty does not include the performance of maintenance and similar operations specified in the user manual, and users are obliged to do it themselves.

If defects occur due to natural wear and tear during use, the warranty does not cover it.

The warranty does not cover:

  • Mechanical damage caused by the user's fault and product defects caused by such damage.
  • Damage caused by improper use of the product.

The rights under the guarantee will expire in the following circumstances:

  • Remove the warranty seal from the product.
  • Remove the serial number from the product.
  • Take action to eliminate physical defects in the product outside of authorized service.
  • Use non-original parts and consumables.

8.2. Declaration of Conformity

Hereby, WENZHOU NOVA NEW ENERGY CO., LTD declares that the radio equipment type BS-FB-V3 is in compliance with Directive 2014/53/EU, 2014/30/EU, 2011/65/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.moestech.com/blogs/news/bs-fb-v3

8.3. Manufacturer Information

Manufacturer: WENZHOU NOVA NEW ENERGY CO.,LTD
Address: Power Science and Technology Innovation Center, NO.238, Wei 11 Road, Yueqing Economic Development Zone, Yueqing, Zhejiang, China
Tel: +86-577-57186815
After Service Email: service@moeshouse.com

8.4. Official User Manual (PDF)

For the complete official user manual in PDF format, please refer to: https://manuals.plus/m/8d3565251f17a0ca1a6987334d4a0394d481a1dad8fce3bf9bcd51cdf3092d6b

9. User Tips

  • A Bluetooth gateway (hub) is required for wireless remote control and voice control by voice assistants (Alexa, Google Home).
  • The robotic arm can be used alone, but it can only be controlled properly within the Bluetooth-compatible connection range (about 10 meters).
  • The Fingerbot works well through the app and can be set to specific times for automation.
  • The device is sturdy and includes a battery for immediate use.
  • The app connection via Bluetooth is generally stable and works effectively.
  • The Fingerbot uses a replaceable CR2 battery and does not require charging.

© 2023 MOES. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.