1. Introduction
Thank you for choosing the RETEKESS TD032 Wireless Call Button. This product features a minimalist design, is easy to operate and install, and is suitable for various basic calling scenarios. To ensure smooth use, please read this instruction manual before use.
The TD032 is a simple universal call button designed for efficient communication in service environments. It is a transmitter that needs to be paired with a compatible RETEKESS receiver (such as a watch receiver) for full functionality. The watch receiver is not included in this package.

2. Product Overview
2.1. Product Structure
External Structure:
- Housing: Made of ABS plastic material, compact and lightweight.
- Call Button: Single-point button on the front, made of soft and comfortable silicone.
- Indicator Light: Embedded LED light in the center of the button to indicate the call status.
- Battery Compartment: Screw-down design on the back, with one built-in specific model battery.
- Mounting Components: High-adhesion adhesive on the back, supports adhesive installation without additional tools.
Internal Structure:
- Simple Wireless Module: Low-power design, stable signal, compatible with universal call hosts.
- Trigger Switch: Linked with the button to ensure activation upon pressing.
2.2. Function Introduction
- One-button Call: A simple press of the button triggers a call signal; easy to use, even for the elderly and children.
- Status Indicator: The LED flashes (red) during a call and automatically turns off after a response.
- Low Power Consumption Design: Extremely low standby power consumption; a single battery lasts for approximately 6000 cycles (around 12 months).
- Easy Installation: Adhesive backing design allows for 3-second installation and easy repositioning.
- Wide Compatibility: Supports pairing with most general-purpose call hosts, adapting to basic call needs.


3. Applicable Scenarios
The RETEKESS TD032 Call Button is ideal for various service environments requiring quick and efficient communication. These include:
- Small restaurants and cafes
- Convenience stores
- Offices
- Homes
- Small clinics and hospitals
- Bars and hookah lounges
- Hotels

4. Setup
4.1. Installation Preparation
- Battery Installation: Unscrew the battery compartment cover on the back of the call button. Insert one 23A12V battery with the positive terminal facing up. Tighten the cover securely.
- Mounting: Select a flat, dry mounting surface. Clean the surface thoroughly. Peel off the protective film from the high-adhesion adhesive backing on the call button and firmly attach the button in the desired location. The adhesive design allows for easy repositioning if needed.

4.2. Device Pairing
The TD032 call button must be paired with a compatible RETEKESS receiver (e.g., a watch receiver) before use. The pairing process typically involves the following steps:
- On your RETEKESS receiver, navigate to the 'Caller Setting' menu.
- Select 'Add/Delete Caller' or a similar option to add a new call button.
- When prompted by the receiver, press and hold the TD032 call button for approximately 5 seconds. The indicator light on the call button will flash rapidly, indicating it has entered pairing mode.
- Once the receiver displays a message like "Pairing Successful," the indicator light on the call button will turn off, confirming successful pairing.
Note: The specific steps for pairing may vary slightly depending on your RETEKESS receiver model. Refer to your receiver's user manual for detailed instructions.
5. Operation
5.1. Call Operation
Once the call button is successfully paired with a receiver, simply press the call button on the front. The LED light will flash briefly, indicating that a call signal has been sent to the paired receiver. The LED light will automatically turn off after the call is acknowledged or answered by the receiver.


6. Maintenance
6.1. Battery Replacement
If the indicator light does not illuminate or flashes weakly after pressing the button, the battery is low and needs to be replaced. To replace the battery:
- Unscrew the battery compartment cover on the back of the call button.
- Remove the old 23A12V battery.
- Insert a new 23A12V battery, ensuring the positive terminal is facing up.
- Tighten the battery compartment cover securely.
6.2. Cleaning
Wipe the call button with a soft, dry cloth. Do not use harsh chemicals or abrasive cleaners, as these may damage the device.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Call button not responding / Indicator light not flashing. | Low or dead battery. | Replace the 23A12V battery (refer to Section 6.1). |
| Call button not communicating with receiver. | Not paired or pairing failed. | Perform the device pairing process again (refer to Section 4.2). Ensure the receiver is in pairing mode. |
| Reduced transmission range. | Obstructions (thick walls, metal structures) or interference. | Ensure clear line of sight or minimize obstructions between the call button and receiver. Check for other wireless devices causing interference. |
| Call button accidentally triggers. | Button pressed unintentionally. | Ensure proper placement where accidental presses are minimized. |
8. Specifications
| Feature | Specification |
|---|---|
| Model Number | TD032 |
| Brand Name | RETEKESS |
| Operating Frequency | 433MHz |
| Wireless Coding | 1527 |
| Operating Voltage | DC12V (23A12V battery) |
| Operating Current | 15±3mA |
| Indicator Light | Red |
| Range | 80m (open area) / 262 ft |
| Waterproof Rating | IP55 |
| Size | Ø60 x H16mm |
| Key Options | 1, 2, 3, 4 series key (English/Russian options available) |
| Color Options | Black |
| Battery Included | Yes |
| Certification | CE, FCC |
| Origin | Mainland China |



9. Package Contents
The standard package for the RETEKESS TD032 Call Button includes:
- 10 x RETEKESS TD032 Call Pager (available in one key, two key, three key, four key, four key-RU, or four key-hookah variants)
- 10 x Stickers


10. User Tips
- For optimal performance, ensure call buttons are placed within the specified transmission range of the receiver.
- Regularly check the indicator light on the call button. A dim or non-flashing light indicates a low battery, which should be replaced promptly.
- When installing, consider placing buttons in easily accessible yet secure locations to prevent accidental activation or tampering.
- If using multiple call buttons, ensure each is uniquely paired to avoid confusion in call identification on the receiver.
11. Safety and Precautions
- Avoid installing the device in direct sunlight or high-temperature, humid environments.
- Do not press or drop the device forcefully to avoid damaging internal components.
- Ensure the battery is installed correctly with the positive and negative terminals aligned to avoid short circuits.
- When not in use for extended periods, remove the battery to prevent leakage and damage to the device.
12. Warranty and Support
For any questions or support needs, please contact RETEKESS customer service:
- Company: Henan Eshow Electronic Commerce Co., Ltd
- Address: 7/F, Sanjiang Building, No.170 Nanyang Road, Huiji District, Zhengzhou, Henan, China
- Website: www.retekess.com
- Facebook: facebook.com/RetekessRadio
- E-mail: support@retekess.com
This product is certified with CE and FCC standards.