WINXU LCD Speed Display Throttle

Contents

WINXU LCD Speed Display Throttle Instruction Manual

For Electric Bicycles, E-bikes, Scooters, and Motorbikes

1. Product Overview

The WINXU LCD Speed Display Throttle is a versatile twist throttle designed for electric bicycles, e-bikes, scooters, and motorbikes. It features an integrated LCD screen that provides essential information such as real-time battery voltage, battery capacity, real-time speed, and mileage. This throttle supports multiple voltage systems (24V, 36V, 48V, 60V) and is compatible with both lithium and lead-acid batteries.

WINXU LCD Speed Display Throttle with key ignition

Figure 1: WINXU LCD Speed Display Throttle

Video 1: Product demonstration of the WINXU LCD Speed Display Throttle.

2. Safety Information

⚠️ Disclaimer: Please mind potential fire risk and strictly follow the instruction manual for charging and storage of your vehicle's battery.

  • Ensure all connections are secure and properly insulated to prevent short circuits.
  • Always turn off the vehicle's power before performing any installation or maintenance.
  • Do not attempt to modify the throttle or its wiring, as this may void the warranty and create safety hazards.
  • Keep the throttle clean and free from debris.

3. Installation Guide

3.1 Physical Installation

  1. Ensure your vehicle's power is OFF.
  2. Remove your existing throttle grip from the handlebar. The WINXU throttle is designed for standard 22mm (0.87 inch) diameter handlebars.
  3. Slide the new WINXU LCD Speed Display Throttle onto the right side of your handlebar.
  4. Secure the throttle in place using any provided fasteners or screws.
Dimensions of the throttle and handlebar diameter

Figure 2: Throttle Dimensions and Handlebar Compatibility (22mm / 0.87 inch)

3.2 Wiring Diagram and Connections

The throttle features a 1.5m (approx. 59 inches) wire length for flexible installation.

Wiring diagram for the LCD Speed Display Throttle

Figure 3: Detailed Wiring Diagram

Connect the wires according to the following descriptions:

  1. Throttle Signal Wire: Connect this wire to the signal wire on your vehicle's controller.
  2. Throttle +5V Wire: Connect this wire to the +5V voltage output for the throttle on your controller.
  3. Throttle -5V Wire: Connect this wire to the negative (ground) for the throttle on your controller.
  4. Electric Door Lock Wire: Connect this wire to the door lock wire on your controller.
  5. Battery Input + Wire: Connect this wire to the controller's power input positive (+) or directly to the battery positive (+).
  6. Speed Display Wire: This throttle uses a phase wire speed measurement design. Connect this wire to the LCD speed display wire on the controller or to the blue phase wire of the motor.

Important Tip: Ensure the Speed Display Wire is correctly connected to a phase wire for accurate speed readings.

4. Operating Instructions

4.1 Powering On/Off

Insert the key into the ignition slot on the throttle and turn it to the 'ON' position to power on the display and activate the throttle. Turn the key to 'OFF' to power down the system.

4.2 LCD Display Functions

The LCD screen provides the following information:

  • Real-time Battery Voltage: Displays the current voltage of your battery (e.g., 39V, 42V).
  • Battery Capacity Display: Shows the remaining battery charge level through a visual indicator.
  • Real-time Speed Display: Shows your current speed in km/h.
  • Mileage Display: Shows the accumulated distance traveled. This mileage is typically cleared when the device is switched off.
LCD display showing battery voltage and mileage

Figure 4: Display in Parking State (Battery Voltage)

LCD display showing real-time speed and mileage

Figure 5: Display in Running State (Real-time Speed)

Note on Speed Accuracy: The speed shown on this LCD is a reference speed. For 100% accurate speed readings, a more advanced and typically more expensive model may be required. Please consult the seller for alternative models if precise speed measurement is critical for your application.

4.3 Using the Throttle

Once powered on, gently twist the throttle grip to accelerate your vehicle. Release the grip to decelerate. The amount of twist directly corresponds to the power delivered to the motor.

5. Maintenance

  • Cleaning: Wipe the throttle and display screen with a soft, dry cloth. Avoid using abrasive cleaners or solvents that could damage the plastic or electronic components.
  • Inspection: Periodically check all wiring connections to ensure they are secure and free from damage. Inspect the throttle grip for any signs of wear or damage.
  • Storage: If the vehicle is not in use for an extended period, store it in a dry, cool place. Ensure the power is turned off.

6. Troubleshooting

ProblemPossible CauseSolution
Display not turning onKey not in 'ON' position, loose wiring, no power from battery/controller.Ensure key is turned to 'ON'. Check all wiring connections, especially Battery Input + and Electric Door Lock wires. Verify battery has charge.
Throttle not respondingLoose throttle signal/power wires, faulty throttle.Check Throttle Signal, Throttle +5V, and Throttle -5V connections. Ensure the display is powered on.
Incorrect speed displaySpeed Display wire incorrectly connected.Ensure the Speed Display wire is connected to the correct phase wire on the motor or controller. Note that this model provides a reference speed.
Mileage resets after power offNormal operation for this model.This is expected behavior. The mileage is not cumulative across power cycles on this specific model.

7. Specifications

FeatureSpecification
Brand NameWINXU
Product NameLCD display throttle
TypeThrottle
Throttle TypeTwist throttle
Battery Voltage Compatibility24V / 36V / 48V / 60V
Working Voltage5V
Signal Output Voltage1.1V - 4.1V
Sensor TypeHall sensor
Wire Length1.5m (approx. 59 inches)
Handlebar Diameter22mm (0.87 inch)
Product Dimensions (approx.)Total Length: 162mm (6.38 inches)
Display Width: 49mm (1.93 inches)
Display Height: 36mm (1.42 inches)
Grip Length: 113mm (4.45 inches)
Package Weight (approx.)0.45 kg
OriginMainland China

8. User Tips

  • Grip Customization: While the throttle comes with a standard grip, some users may wish to replace the non-throttle grip with a custom one. Ensure any replacement grip is compatible with the handlebar diameter and does not interfere with the throttle's operation or wiring.
  • Voltage Compatibility: This throttle is designed to work with a wide range of battery voltages (24V, 36V, 48V, 60V). When connecting, ensure your vehicle's battery voltage falls within this range for proper function and display accuracy. For example, a 30V battery system would be compatible.
  • Wheel Size Setting: This specific model does not provide explicit instructions for setting wheel size. If your controller or vehicle system requires wheel size input for accurate speed/mileage, you may need to configure it through the controller's interface, not the throttle itself.

9. Warranty and Support

For warranty information, technical support, or any product-related inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.