1. Introduction and Overview
The Beitian M9 Chip GNSS Module (e.g., BK-180i variant) is designed to provide superior sensitivity and rapid acquisition time for all L1 GNSS systems. This standard-precision GNSS platform offers meter-level accuracy performance, making it an enhanced solution for various applications. It is particularly suitable for automotive and industrial tracking applications, including navigation, telematics, and drones.
The module supports the simultaneous reception of four GNSS signals, allowing the receiver to select the best available signal. This capability significantly maximizes positioning accuracy, especially in challenging environments such as urban canyons. With a position update rate of up to 25 Hz, the module is ideal for dynamic applications like drones, providing location information with minimal latency. Furthermore, the BK-180i is equipped with features to detect jamming and spoofing events, reporting them to the host system. Advanced filtering algorithms are integrated to mitigate the effects of RF interference, ensuring reliable performance.
2. Product Features
- Maximum location availability with 4 GNSS simultaneous receptions.
- Working modes: GPS, GLONASS, BDS, GALILEO.
- 25 Hz position update rate for dynamic applications.
- Advanced anti-spoofing capabilities and interference detection.
- Pathways to the migration of dead reckoning and high-precision techniques.
- Support for LED light display.
- GPS+ antenna integrated module.
- Built-in electronic compass IST8310.
3. Specifications
3.1. General Performance Indicators (Based on BK-180i)
| Item | Description |
|---|---|
| Chip | M9140-KB |
| Receiver type | GPS L1 C/A, QZSS L1 C/A/S, GLONASS L1OF, BDS B1I, Galileo E1B/C, SBAS L1 C/A (WAAS, EGNOS, MSAS, GAGAN) |
| Default position system | GPS, GLONASS, BDS, GALILEO |
| Augmentation system | SBAS, QZSS |
| Channel | 92 Searching Channel |
| Tracking & Navigation Sensitivity | -167dBm |
| Reacquisition Sensitivity | -160dBm |
| Cold start Sensitivity | -148dBm |
| Hot Start Sensitivity | -159dBm |
| Horizontal position Accuracy | 1.5 m CEP |
| Velocity Accuracy | 0.05m/s |
| Dynamic heading Accuracy | 0.3 deg |
| Time pulse Accuracy | RMS 30ns, 99% 60ns |
| Cold start Acquisition | 24s |
| Hot start Acquisition | 2s |
| Aided start Acquisition | 2s |
| Baud rate | 4800bps - 921600bps, Default 115200bps |
| Level | TTL Level |
| Protocol | NMEA, UBX |
| NMEA messages | RMC, VTG, GGA, GSA, GSV, GLL |
| Update rate | 0.25Hz-25Hz, Default 1Hz |
| FLASH | With FLASH, the configuration can be changed, and the power will not be lost |
| Frequency of time pulse signal | 0.25 Hz to 10 MHz configurable, the default period is 1s, and the high level lasts for 100ms |
| Max Altitude | 80,000m |
| Max Speed | 500m/s |
| Gravitational acceleration | ≤4g |
| Voltage | DC Voltage 3.6V-5.5V, Typical: 5.0V |
| Current | 45mA/5.0V |
| Size | 18*18*6.2mm |
| Weight | 5.4g |
4. Pin Definition and Physical Characteristics
- Package: 1.00/6P unlocked, horizontal SMD socket.
- Operating Temperature: -40 °C to +85°C.
- Storage Temperature: -40°C to +105°C.
- LED Indicators:
- TX LED (Blue): Flashes when data is output.
- PPS LED (Red): Not bright when GPS is not fixed, flashes when fixed.
- Compass: Built-in electronic compass IST8310.
4.1. Pinout Table
| PIN | Name | I/O | Description | Characteristic |
|---|---|---|---|---|
| 1 | TX | O | UART communication interface, TTL level | GPS data output |
| 2 | RX | I | UART communication interface, TTL level | GPS data input |
| 3 | GND | G | Ground | Ground |
| 4 | VCC | I | Supply voltage | DC 3.6V-5.5V; suggest 5.0V |
| 5 | SCL | I | Serial Clock - I2C bus master/slave clock | IST8310 compass clock |
| 6 | SDA | O | Serial Data - I2C Bus Master/Slave Data | IST8310 compass data |
4.2. Rear View and Electronic Compass Orientation
The electronic compass IC IST8310 is positioned on the rear of the module. Its orientation is crucial for accurate heading data.
5. Functional Frame Diagram
The following diagrams illustrate the functional layout of the Beitian GNSS module from both front and rear perspectives, highlighting key components such as the GPS module, ceramic antenna, compass, indicator lights, and serial port output.
6. Dimensions
The physical dimensions of the Beitian GNSS module are detailed in the diagram below. Understanding these measurements is essential for integration into various projects and enclosures.
Video 6.1: Demonstrating the compact size of the Beitian BK-122 GPS module using a caliper.
7. Hardware Interface
7.1. Power Supply (VCC)
The module features a VCC pin for power input. A built-in Farad capacitor stores energy to supply power to the RTC (Real-Time Clock) circuit when the main VCC is powered off. This ensures that key information is retained, enabling the hot start function.
7.2. Module Serial Port
The module utilizes a 1.00 6P UART serial port for communication. The pins are: TX, RX, GND, VCC, SCL, SDA.
7.3. 1PPS Signal Interface
The 1PPS (One Pulse Per Second) signal interface is available for precise timing applications.
7.4. UART Interface Details
The UART serial port (TX and RX) outputs NMEA data at the UTC second boundary. The host computer can interact with the module to switch working modes and upgrade software via this port. The supported baud rate range is 4800bps to 921600bps, with a default setting of 115200bps. The data format is 1 start bit, 8 data bits, 1 stop bit, and no check bit. It can be used for custom data output and software upgrades.
8. Data Output Protocol
The module outputs data using standard NMEA and UBX protocols. Below is a summary of common NMEA messages and their fields.
8.1. NMEA Messages
- $GNRMC (Recommended Minimum Specific GNSS Data): Provides time, status, latitude, longitude, speed, course, date, and magnetic variation.
- $GNVTG (Course Over Ground and Ground Speed): Reports course and speed relative to the ground.
- $GNGGA (Global Positioning System Fix Data): Contains time, position, fix indicator, number of satellites, HDOP, altitude, and geoid separation.
- $GNGSA (GNSS DOP and Active Satellites): Details the dilution of precision (DOP) and the IDs of satellites used in the fix.
- $GPGSV / $GLGSV / $GAGSV / $GBGSV (GNSS Satellites in View): Provides information about satellites in view, including satellite ID, elevation, azimuth, and signal strength.
- $GNGLL (Geographic Position - Latitude/Longitude): Reports latitude, longitude, time, and data validity.
For detailed field descriptions and examples of NMEA sentences, please refer to the comprehensive PDF user manual available for download.
9. Installation Guide
When handling the module, carefully inspect all components for any signs of looseness or damage. The installation process for other modules in the series is generally similar.
9.1. Connection Diagram
To connect the GNSS module to a PC for configuration or data monitoring, a USB to TTL level conversion cable (e.g., using a PL-2303HX/TA chip) is required.
10. Precautions
- The VCC power supply ripple for the module should be controlled within 45mA/5.0V. Avoid any interference on the power supply line.
- Ensure that the baud rate of the host computer's serial port is consistent with the module's baud rate (default 115200bps).
- Control the temperature carefully during module soldering to prevent damage.
- To ensure the hot start function operates correctly, verify that the backup power supply (Farad capacitor) is functioning normally.
11. User Tips
- Check Update Rate: If you require a high update rate for dynamic applications like drones, ensure your specific module variant supports 25Hz output. The BK-180i is designed to support up to 25Hz.
- Power Stability: Maintain a stable and clean power supply to the module to prevent erratic behavior or signal loss.
- Compass Calibration: For applications relying on the built-in IST8310 compass, perform proper calibration to ensure accurate heading information.
12. Frequently Asked Questions (FAQ)
- Q: Does the M9 Chip GNSS Module (e.g., BK-280U variant) support a 25Hz update rate?
- A: Yes, the M9 Chip GNSS Modules, including variants like the BK-180i and others in the series, are designed to support a position update rate of up to 25Hz for dynamic applications. The default update rate is 1Hz, but it can be configured to 25Hz.
13. Warranty and Support
Beitian is responsible for the safety, reliability, and performance of the module under the following conditions:
- Assembly, expansion, readjustment, improvement, or repair are performed by personnel approved by Beitian Communication Co., Ltd.
- The equipment is used in accordance with the operating requirements specified in this manual.
For technical support, inquiries, or service, please contact Shenzhen Beitian Communication Co., Ltd. directly:
- Address: Whole Floor 9, Building 1, Phase 5, Fucheng Digital Innovation Park, Shijing Road, Fucheng Street, Longhua District, Shenzhen
- Tel: 0755-22225474
- Fax: 0755-22225474
- Website: www.beitian.com