1. Introduction
This manual provides detailed instructions for the operation and maintenance of your LAUNCH CR629 OBD2 Scanner. The CR629 is a powerful diagnostic tool designed to support all 10 modes of OBD II tests, offering comprehensive vehicle diagnosis. It features a 3.5" TFT color display for clear data presentation and includes built-in help menus and code definitions to simplify troubleshooting.
Key functions include reading and clearing Diagnostic Trouble Codes (DTCs), viewing live data streams, freeze frame data, I/M readiness status, O2 sensor tests, on-board monitor tests, and retrieving vehicle information. Additionally, it supports advanced functions such as ABS and SRS system diagnosis, Active Tests, and essential reset services for Oil, Steering Angle Sensor (SAS), and Battery Management System (BMS). The device offers lifetime free updates via PC to ensure compatibility with the latest vehicle models and software versions.
The LAUNCH CR629 is designed to work with all OBD II compliant vehicles. This includes most US-based cars from 1996 onwards, EU-based cars from 2000 onwards, and Asia-based cars from 2008 onwards. For older vehicles (1994-1995), ensure the Vehicle Emissions Control Information (VECI) label states "OBD II Certified".

Figure 1.1: LAUNCH CR629 OBD2 Scanner and its components.
2. Safety Precautions and Warnings
To prevent personal injury or damage to vehicles and/or the test equipment, please read this user's manual carefully and observe the following safety precautions at a minimum whenever working on a vehicle:
- Always perform automotive testing in a safe environment.
- Do not attempt to operate or observe the tool while driving a vehicle, as this can cause driver distraction and lead to a fatal accident.
- Wear safety eye protection that meets ANSI standards.
- Keep clothing, hair, hands, tools, and test equipment away from all moving or hot engine parts.
- Operate the vehicle in a well-ventilated work area, as exhaust gases are poisonous.
- Put blocks in front of the drive wheels and never leave the vehicle unattended while running tests.
- Use extreme caution when working around the ignition coil, distributor cap, ignition wires, and spark plugs, as these components create hazardous voltages when the engine is running.
- Put the transmission in Park (P) for automatic transmission (A/T) or Neutral (N) for manual transmission (M/T) and ensure the parking brake is engaged.
- Keep a fire extinguisher suitable for gasoline/chemical/electrical fires nearby.
- Do not connect or disconnect any test equipment while the ignition is on or the engine is running.
- Keep the test equipment dry, clean, free from oil/water or grease. Use a mild detergent on a clean cloth to clean the outside of the test equipment when necessary.
2.1 FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
3. Product Description
3.1 General Controls
The LAUNCH CR629 features an intuitive interface with clearly labeled buttons and indicators:

Figure 3.1: LAUNCH CR629 General Controls Layout.
| No. | Name | Notes |
|---|---|---|
| 1 | DB-15 Diagnostic Connector | Connects the tool to the vehicle’s Data Link Connector (DLC). |
| 2 | USB Port | Connects the tool to a computer via USB cable for upgrade. |
| 3 | Memory Card Slot | Insert the memory card into it to read or write data/files. |
| 4 | DTC Button (F2) | Clears diagnostic trouble codes. |
| 5 | I/M Button (F3) | Quick access to I/M readiness function. Deletes diagnostic record in Print function. |
| 6 | Return Button | Returns to previous menu. |
| 7 | OK Button | Confirms a selection or action from a MENU list. |
| 8 | Navigation Buttons (Up/Down/Left/Right) | Scrolls through menus/submenus. Scrolls screen data (NEXT/PREVIOUS page) when linked to a vehicle. |
| 9 | HELP Button (F1) | Quick access to Help function. |
| 10 | Read DTC Button | Reads diagnostic trouble codes. |
| 11 | LED for different DTC types | Green (No Fault Code), Yellow (Pending Fault Code), Red (Permanent Fault Code). |
| 12 | LCD Screen | Displays test results. |
3.2 Specifications
| Feature | Detail |
|---|---|
| Screen | 3.5" LCD display with 320x480 pixels resolution |
| Input Voltage Range | 9 ~ 18V |
| Operating Temperature | 0°C ~ 50°C (32°F ~ 122°F) |
| Storage Temperature | -20°C ~ 70°C (-4°F ~ 158°F) @ RH60% |
| Product Dimensions | 4.49 x 8.46 x 1.36 inch (approx. 11.4 x 21.5 x 3.45 cm) |
| Weight | About 500g |
| Connection | OBD2 Plug 16 Pin Cable |
| Wireless Function | Yes |
| Wireless Support | Wifi |
| Battery Included | Yes |
| Software Update | Yes (Lifetime Free Update) |
| Warranty | 1 Year |
3.3 Vehicle Coverage
The LAUNCH CR629 supports a wide range of vehicles for OBD2 functions and specific system diagnoses (ABS, SRS, Oil Reset, SAS Reset, BMS Reset). General OBD2 functions are compatible with:
- US-based Cars: 1996 and newer
- EU-based Cars: 2000 and newer
- Asia-based Cars: 2008 and newer
For ABS & SRS, Oil Reset, and SAS Reset, the tool supports numerous brands across different regions:

Figure 3.3: Vehicle Coverage Summary.
Specific brand coverage includes:
- Europe: Audi, Benz, BMW, Citroen, Dacia, Fiat, Jaguar, Land Rover, Mini, Opel, Peugeot, Porsche, Renault, Saab, Seat, Skoda, Smart, Sprinter, Volvo, VW, Europe Ford, Alfa Romeo, Vauxhall.
- Asia: Acura, Daewoo, Honda, Hyundai, Infiniti, JP Isuzu, Kia, Mazda, Mitsubishi, Nissan, Subaru, Suzuki, Toyota.
- America: Chrysler, GM, USA Ford.
- Australia: Holden, Australia Ford.
The device also supports multiple languages for user interface:

Figure 3.4: Supported Languages.
3.4 Accessories (Package List)
The following items are included in your LAUNCH CR629 package:
- 1 * OBD II Scanner (LAUNCH CR629 unit)
- 1 * Diagnostic Cable (OBD2 Plug 16 Pin Cable)
- 1 * Memory Card (Gift)
- 1 * Memory Card Adaptor (Gift)
- 1 * USB cable (for connecting to a computer for online upgrading)
- 1 * Quick Start Guide
- 1 * User's Manual (PDF available online: View PDF)

Figure 3.5: Package List for LAUNCH CR629.
4. Initial Use (Connection)
Follow these steps to connect your LAUNCH CR629 to your vehicle:
- Turn the vehicle's ignition OFF.
- Locate the vehicle's 16-pin Data Link Connector (DLC). The DLC is usually located within 12 inches of the center of the instrument panel (dash), under or around the driver's side. For some Asian and European vehicles, it might be behind the ashtray. If you cannot find it, refer to your vehicle's service manual.
- Plug the diagnostic cable of the CR629 tool into the vehicle's DLC.
- Turn the vehicle's ignition ON. The engine can be off or running.
- The system will automatically power on and navigate to the main menu screen.
CAUTION: Do not connect or disconnect any test equipment while the ignition is ON or the engine is running.
Notes:
- A plastic DLC cover may be present on some vehicles; remove it before plugging in the diagnostic cable.
- The cable connector is keyed and will only fit one way. If you encounter difficulty, rotate the connector 180° and try again.
5. Operating the LAUNCH CR629
5.1 Main Menu Overview
The main menu provides access to the following function modules:

Figure 5.1: LAUNCH CR629 Main Menu.
- ABS/SRS: Accesses Anti-Lock Braking System and Supplemental Restraint System for deep diagnostics.
- OBD II: Provides full OBD2 functions for engine diagnostics, including reading/clearing DTCs, I/M readiness, live data, and more.
- SERVICE: Performs common repair and maintenance items like oil lamp reset and steering angle calibration.
- REVIEW: Allows reviewing and deleting recorded DTCs, data streams, and freeze frame data.
- LOOKUP: Provides definitions for Diagnostic Trouble Codes.
- PRINT: Manages printing of diagnostic records via PC.
- HELP: Offers general knowledge about DLC location, tool information, and OBD.
- SETUP: Configures tool settings such as language, unit of measure, and record mode.
5.2 OBDII/EOBD Diagnosing
This module provides a quick way to check for DTCs, isolate the cause of the Malfunction Indicator Lamp (MIL), check monitor status, verify repairs, and perform other emission-related services.
- From the main menu, select [OBD II] and press [OK]. The tool will automatically detect the vehicle's communication protocol and establish a link.
- The screen will then display the Monitor Status, indicating the status of various emission-related monitors.
Note:
- A PROTOCOL is a set of rules for data transmission. The tool supports ISO 9141, Keyword 2000, J1850 PWM, J1850 VPW, and CAN.
- The "Malfunction Indicator Lamp" (MIL) is the dashboard light (often "Check Engine" or "Service Engine Soon") that warns of an emissions-related fault.
5.2.1 Read Codes
This function allows you to view Diagnostic Trouble Codes (DTCs) retrieved from the vehicle's computer.
- Select [Read Codes] from the Diagnostic Menu and press [OK]. The system will display SAE-standard DTCs.
- DTC Structure: DTCs are five-digit alphanumeric codes. The 1st character indicates the main system (B=Body, C=Chassis, P=Powertrain, U=Network). The 2nd character (0-3) indicates the code type (0=Generic, 1=Manufacturer Specific, 2/3=Generic/Manufacturer Specific). The 3rd character (0-9, A-F) identifies the specific system/sub-system. The 4th and 5th characters identify the malfunctioning section.
- Pending DTC: A code recorded on the "first trip" for a "two-trip" code. The YELLOW LED on the scanner will light up.
- Permanent DTC: A DTC that indicates a problem in one or more systems. The RED LED on the scanner will light up, and the MIL will be steady ON.
- Use the navigation buttons to scroll through multiple DTCs or long definitions. Press [OK] to record DTCs for printing.
- If manufacturer-specific codes are found, you may need to manually select the vehicle manufacturer.
CAUTION: Never replace a part based solely on the DTC definition. Always consult the vehicle's service manual for proper testing procedures.
5.2.2 Erase Codes
This function clears DTCs from the vehicle's computer. Note that "Freeze Frame" data will also be erased, and "Permanent" DTCs are NOT erased.
WARNING: If you plan to take the vehicle for repair, DO NOT erase codes as valuable diagnostic information will be lost. Ensure the ignition is ON and the engine is OFF before erasing codes.
Note:
- Erasing DTCs resets I/M Readiness Monitors to "Not Completed". An OBD II Drive Cycle must be performed to set them to "Completed".
- After clearing, re-check for codes. If codes persist, troubleshoot using a factory diagnosis guide.
5.2.3 I/M Readiness
This indicates whether emission-related systems are operating properly and are ready for Inspection and Maintenance testing. Select [I/M Readiness] from the Diagnostic Menu and press [OK] to view the results (N/A = not available, INC = incomplete/not ready, OK = completed/monitor OK).
5.2.4 Data Stream
Retrieves and displays live data and parameters from the vehicle's Engine Control Unit (ECU). The CR629 supports graphic data stream display for easier analysis.
5.2.5 View Freeze Frame
When an emission-related fault occurs, the on-board computer records a "snapshot" of operating conditions at that moment. This data is called Freeze Frame data.
5.2.6 O2 Sensor Test
Retrieves and displays O2 sensor monitor test results for recently completed tests.
5.2.7 On-board Monitor Test
Reads results of on-board diagnostic monitoring tests for specific components/systems.
5.2.8 EVAP System Test
Initiates a leak test for the vehicle's Evaporative System (EVAP). The tool signals the vehicle's computer to perform the test; it does not perform the test itself. Refer to your vehicle's service manual for test procedures.
5.2.9 Vehicle Info
Retrieves information from the vehicle's on-board computer, including VIN (Vehicle Identification Number), CID (Calibration ID), and CVN (Calibration Verification Number).
5.3 System Diagnosing (ABS & SRS)
This function is specifically designed to diagnose Anti-lock Braking System (ABS) and Supplemental Restraint System (SRS) for single vehicle models.

Figure 5.2: ABS & SRS Diagnostic Capabilities.
Notes:
- Ensure the diagnostic program for the specific vehicle model is installed on the tool.
- Diagnostic menus may vary between vehicle manufacturers. Follow on-screen instructions.
The diagnostic process typically involves:
- Select "ABS/SRS" from the main menu.
- Select Vehicle Manufacturer and then Vehicle Model (e.g., by make year or chassis).
- Choose a scan mode (Automatic or Manual Select).
- Select the desired test function:
- Read Version Info: Identifies specific control unit information (unit type, version numbers).
- Read / Clear DTCs: Reads diagnostic trouble codes to identify faults and clears them after repairs to turn off warning lights.
- Read Live Data: Retrieves real-time data streams (coolant temperature, MAP, TPS, vehicle speed, etc.) for analysis.
- Active Test: (Manual mode only) Sends commands to vehicle control modules to test devices.
5.4 Service (Oil/SAS/BMS Reset)
The CR629 offers essential service functions for common maintenance tasks:

Figure 5.3: Oil, SAS, and BMS Reset Services.
- Oil Lamp Reset: Resets the oil service light after an oil change. This is crucial for tracking maintenance intervals.
- Steering Angle Sensor (SAS) Reset: Recalibrates the SAS after steering system changes (e.g., alignment) to ensure accurate steering wheel angle information for the Electronic Stability Control (ESC) module.
- Battery Management System (BMS) Reset: Clears unhealthy status memories of a replaced battery in the ECU, allowing the ECU to properly recognize and record the new battery's status.
There are two methods for service reset: Manual Reset and Auto Reset. Auto Reset sends commands from the tool to the vehicle's ECU. Manual Reset requires users to follow on-screen instructions, select options, enter data, and perform necessary actions.
The general procedure for performing a service reset is:
- Select "SERVICE" from the main menu.
- Choose the desired service function (e.g., oil lamp reset).
- Select the desired car brand.
- Select the reset mode (varies by vehicle).
- Follow the on-screen instructions to proceed.
5.5 DTC Lookup Function
This option allows users to quickly retrieve diagnostic trouble code definitions from the built-in DTC library.

Figure 5.4: DTC Lookup Interface.
To use the DTC Lookup function:
- Select [LOOKUP] on the main menu screen and press [OK].
- Input the target DTC using the navigation buttons to move the highlight bar and alter values.
- Press [OK] to confirm, and the screen will display the detailed definition of the DTC.
6. Maintenance
6.1 Register & Update
To ensure optimal performance and access to the latest vehicle data, it is recommended to register and update your CR629 scanner. The tool can be updated via memory card.
Prerequisite Conditions:
- A computer with Windows XP, 7, 8, or 10 operating system.
- Internet access to download the update tool.
Steps for Registration and Update:
- Download Update Tool: Go to www.x431.com/CR629 to download and install the update tool on your computer.
- Note Down Serial Number and Register Code:
- Connect the CR629 to your computer via the USB cable.
- Once the tool powers up and enters the main menu, navigate to the "Help" icon and press [OK].
- Highlight "Tool Information" and press [OK] to view the Boot version, Display program version, Diagnostic program version, Diagnostic library version, Serial Number, and Register Code. Note down the Serial Number and Register Code as they are required for registration.
- Register the Scanner on the Update Tool:
- Launch the update tool on your computer.
- Enter your E-mail address and the Register Code. Click [Submit] to complete the sign-up. (For initial update, a registration process is required. Subsequent updates will not require re-registration).
- Copy the Update Package to Memory Card:
- Install the memory card from the tool into the supplied memory card adaptor and insert it into your computer's USB port.
- Reopen the update tool, select the updates you wish to perform (or "Select All"), and click [Download] to transfer the update package to the memory card.
- Reinsert Memory Card and Start Update:
- Once the download is complete, reinsert the memory card into the CR629 tool.
- Power up the tool via the USB cable. The tool will automatically verify files and begin updating. A green progress bar will indicate the update status. Be patient until the update is finished.

Figure 6.1: Update and Data Printing Process.
6.2 Printing Diagnostic Reports
This function allows you to print records saved from the Read Codes or Data Stream screens.
Note: The Print Manager is integrated into the update tool. You must download and install the update tool on your computer to use this function.
Steps for Printing:
- Launch the update tool on your computer.
- Connect the CR629 to your computer via the USB cable. The tool's serial number should be automatically detected.
- Click [Print Manager] in the update tool.
- On the CR629, select [PRINT] from the main menu and press [OK] to enter the diagnostic record list screen. Select the desired record and press [OK].
- The Print Manager on your computer will synchronize and display all reports from the scanner.
- Use the on-screen buttons in the Print Manager to:
- Modify personal information (displayed on the report).
- Export the current report to your local disk.
- Clear all contents of the current report.
- Print the current report via a connected printer.
- Exit the update tool.
7. Troubleshooting (FAQ)
Here are some frequently asked questions and answers regarding the LAUNCH CR629:
- Question: System halts when reading data stream. What is the reason?
- Answer: This may be caused by a slackened connector. Turn off the tool, firmly connect the connector, and switch it on again.
- Question: Screen of main unit flashes at engine ignition start.
- Answer: This is a normal phenomenon caused by electromagnetic disturbing.
- Question: There is no response when communicating with the on-board computer.
- Answer: Confirm the proper voltage of the power supply. Check if the throttle has been closed, the transmission is in the neutral position, and the water temperature is proper.
- Question: Why are there so many fault codes?
- Answer: Usually, this is caused by poor connection or fault circuit grounding.
- Question: What to do if the tool fails to boot up?
- Answer: Connect the tool to the USB port of a computer to fix the firmware.
8. User Tips
- ABS Sensor Diagnosis: The CR629 is effective in identifying issues with ABS sensors. Users have successfully used it to pinpoint defective ABS sensors, such as those in a BMW 325I.
- Vehicle Compatibility: While the CR629 supports a wide range of OBD II compliant vehicles, always verify compatibility for your specific make, model, and year, especially for older vehicles (e.g., 2004 Suzuki Ignis). Refer to your vehicle's manual or the CR629's specifications for detailed coverage.
9. Warranty and Customer Support
9.1 Warranty Information
The LAUNCH electronic product is warranted against defects in materials and workmanship for one year (12 months) from the date of delivery to the user. This warranty is expressly limited to persons who purchase LAUNCH products for purposes of resale or use in the ordinary course of the buyer's business.
What the Warranty Does NOT Cover:
- Any part that has been abused, altered, or used for a purpose other than its intended use.
- Use in a manner inconsistent with instructions regarding use.
The exclusive remedy for any defective automotive meter is repair or replacement. LAUNCH shall not be liable for any consequential or incidental damages. Final determination of defects will be made by LAUNCH in accordance with established procedures. No agent, employee, or representative of LAUNCH has the authority to bind LAUNCH to any affirmation, representation, or warranty concerning LAUNCH automotive meters, except as stated herein.
9.2 Customer Service
If you have any questions regarding the operation of the unit, please contact your local dealer or LAUNCH TECH. CO., LTD. directly:
- Telephone: +86-755-84527891
- E-mail: overseas.service@cnlaunch.com