E-ACE K01/K02

Contents

E-ACE Solar Power TPMS Car Tire Pressure Alarm Monitor System

User Manual

1. Product Overview

Thank you for purchasing the E-ACE Tire Pressure Monitoring System (TPMS). This system is designed to enhance driving safety by providing real-time tire pressure and temperature monitoring. It alerts the driver to abnormal tire conditions with warning sounds and flashing icons, helping to prevent accidents and ensure the safety of occupants.

Key Features:

  • Dual Charging: Solar power charging and USB charging for continuous operation.
  • Clear Display: Colorful LCD Digital display shows tire information clearly.
  • Real-time Monitoring: Continuously monitors pressure and temperature of 4 tires.
  • Multiple Alarms: Alerts for low air pressure, high temperature, leakage, and low battery.
  • Intelligent On/Off: Automatically activates when the car moves and shuts down when stationary.
  • Easy Installation: Wireless connection by sensors for straightforward setup.
  • Sensor Options: Available with both built-in and external sensors to suit various needs.
  • Wide Compatibility: Freescale chip sensors are compatible with almost 98% of cars on the market.

Video: Unboxing and demonstration of the E-ACE TPMS system.

2. Setup Instructions

2.1. Package Contents

The package contents vary slightly depending on whether you choose the K01 (External Sensor) or K02 (Built-in Sensor) model.

Package contents for K01 External Sensor model

Image: Package contents for K01 External Sensor model, including monitor, spare battery, external sensors, fixed sticker, instructions, screw nuts, wrench, and USB power cable.

Package contents for K02 Built-in Sensor model

Image: Package contents for K02 Built-in Sensor model, including monitor, built-in sensors, fixed sticker, instructions, and USB power cable.

2.2. Monitor Interface and Buttons

The monitor features a clear display and intuitive buttons for operation.

E-ACE TPMS Monitor Display and Buttons

Image: E-ACE TPMS Monitor Display and Buttons. This diagram shows the solar panel, USB charging interface, tire pressure and temperature displays, battery status, and the Select, Menu, and Power/Left buttons.

Button Functions:

  • Power/Left Button: Short press to adjust brightness in standby mode, long press to turn on/off. Also used to switch menu items to the left.
  • SET Button (M): In standby mode, long press to enter menu mode. Short press to confirm selected parameters.
  • Right Button: Short press to adjust brightness in standby mode, long press to turn off alarm. Also used to switch menu items to the right.

2.3. Initial Charging and Activation

Important: Please charge the monitor first to activate the battery before installation.

Upon receiving the product, charge the monitor via USB for approximately 3-4 hours. The TPMS may automatically start during transportation and deplete its battery. It is normal if the device does not turn on immediately upon arrival; a full charge will activate it.

Monitor Charging Activation Diagram

Image: Diagram illustrating the monitor's state before and after initial USB charging, showing it unable to work, then charging for 3-4 hours, and finally working normally.

2.4. Sensor Installation

Important: Turn on the monitor before installing the sensors.

After turning on the monitor by pressing and holding the power button, proceed with sensor installation. Install external or built-in sensors one by one according to the instructions below.

Monitor Power-On and Sensor Installation Steps

Image: Steps for powering on the monitor and installing sensors. First, press and hold the power button to turn on the monitor, then install the sensors one by one.

External Sensor Installation:

  1. Screw the anti-theft nut onto the valve stem first.
  2. Install the sensor onto the valve stem according to its position (e.g., F.L for Front Left) and tighten it.
  3. Screw the anti-theft nut counter-clockwise against the sensor.
  4. Use the provided wrench to tighten both the sensor and the anti-theft nut securely.
  5. If no pressure is displayed for the corresponding position on the monitor, reinstall the sensor.
External Sensor Installation Diagram

Image: Step-by-step diagram for external sensor installation, showing how to screw on the anti-theft nut, tighten the sensor, and secure it with the nut and wrench.

Built-in Sensor Installation:

Built-in sensors require professional installation. It is recommended to have them installed by a professional car service center.

  1. Remove the original tire valve.
  2. Mount the tire pressure sensor.
  3. Pump up the tires.
  4. Cover the valve bonnet.
  5. Perform balancing machine test.
  6. Regulate and counterbalance, installing balance block.
Built-in Sensor Installation Diagram

Image: Step-by-step diagram for built-in sensor installation, showing removal of original valve, mounting sensor, inflating tire, covering valve, balancing, and counterbalancing.

After installation, inflate the tires sequentially. The air must be filled when the main unit is turned on. The main unit can be placed on the left side of the center console using the adhesive pad. The product does not require manual on/off.

3. Operating Instructions

The system defaults to factory settings. To enter system settings, long press the 'Menu' button for 3 seconds. If there is no operation for 30 seconds, the system will automatically exit the menu. Settings not confirmed will not be saved.

3.1. Unit Setting (Factory Default: Bar, °C)

  1. In standby mode, long press the 'Menu' button for 3 seconds to enter system settings. The 'Bar' icon will appear.
  2. Press the 'Menu' button to enter the operable setting state.
  3. Use the 'Left' and 'Right' buttons to select 'Psi' or 'Bar'.
  4. Press the 'Menu' button to confirm the unit.
  5. To set the temperature unit, press the 'Right' button once to navigate to temperature unit setting.
  6. Press the 'Menu' button to enter the operable setting state.
  7. Use the 'Left' and 'Right' buttons to select '°C' or '°F'.
  8. Press the 'Menu' button to confirm the unit.

3.2. Time Setting (For models with clock function only)

  1. In standby mode, long press the 'Menu' button for 3 seconds to enter system settings.
  2. Press the 'Right' button twice to enter time setting.
  3. Short press the 'Menu' button twice; the hour number will flash.
  4. Use the 'Left' and 'Right' buttons to adjust the hour.
  5. Short press the 'Menu' button to set the minutes.
  6. Adjust the minutes using the 'Left' and 'Right' buttons.
  7. Long press the 'Menu' button to exit the setting.

3.3. Adjusting Tire Pressure Limits

  1. In standby mode, long press the 'Menu' button for 3 seconds to enter system settings.
  2. Press the 'Right' button twice to enter the maximum air pressure setting.
  3. Press the 'Menu' button once; the air pressure number will flash.
  4. Use the 'Left' and 'Right' buttons to set the maximum air pressure.
  5. Long press the 'Menu' button to exit.
  6. To set the lower limit, press the 'Right' button three times to enter the lower limit setting.
  7. Press the 'Menu' button once; the barometric pressure number will flash.
  8. Use the 'Left' and 'Right' buttons to set the lower limit parameter value.
  9. Long press the 'Menu' button to exit.

3.4. Adjusting Temperature Limits

  1. In standby mode, long press the 'Menu' button for 3 seconds to enter system settings.
  2. Press the 'Right' button four times to enter the tire temperature upper limit setting.
  3. Short press the 'Menu' button once; the tire temperature number will flash.
  4. Use the 'Left' and 'Right' buttons to set the highest upper limit tire temperature.
  5. Long press the 'Menu' button to exit.

4. Maintenance

4.1. External Sensor Battery Replacement

External sensors use replaceable CR1632 button batteries with a working temperature range of -30℃ to 80℃. It is recommended to replace batteries one by one to avoid mixing or incorrect reassembly.

  1. Remove the dismantling gasket.
  2. Use the provided wrench to unscrew the shell.
  3. Remove the old battery.
  4. Insert a new CR1632 battery, ensuring the positive (+) side faces upwards.
  5. Reassemble the sensor and tighten it with the wrench.
External Sensor Battery Replacement Steps

Image: Diagram showing the steps to replace the battery in an external sensor: remove gasket, wrench shell, remove battery, replace with new battery.

4.2. Built-in Sensor Battery Life

Built-in sensors have a battery life of approximately 5 years and are generally not user-replaceable. If the battery runs out, the sensor typically needs to be replaced by a professional.

5. Troubleshooting

5.1. Single Sensor Replacement and Pairing

If a single sensor needs replacement, first remove the old sensor and install the new one. Then, re-pair it with the monitor:

  1. In standby mode, long press the 'Menu' button for 3 seconds to enter system settings.
  2. Press the 'Right' button five times to enter pairing selection mode.
  3. Press the 'Menu' button once; the '0' on the interface will flash, indicating the front left wheel by default.
  4. Use the 'Left' and 'Right' buttons to select the position of the sensor to be replaced (0=front left, 1=front right, 2=rear left, 3=rear right).
  5. After selecting the position, press the 'Menu' button; the number will flash.
  6. Install the new sensor on the tire. Observe if the number on the monitor changes.
  7. Once the number changes, long press the 'Menu' button to exit.

Note: If it's a built-in sensor, inflate and deflate the tire when the number below flashes. Any sensor can be matched to any position during this process.

5.2. Restore Factory Settings (Re-pairing All Sensors)

To restore the monitor to factory settings and re-pair all sensors:

  1. While powered on, long press the 'Menu' button for 3 seconds to enter settings.
  2. Press the 'Left' button to navigate to item 7.
  3. Press the 'Menu' button twice to reset the machine and restore factory settings. The monitor will then search for sensors.
  4. To update sensors, install new sensors on the valves in order, or drive the car at a speed of 30 km/h or more after resetting.
  5. After driving for about 10-30 minutes, the monitor will automatically search for sensor signals. Once all 4 sensors are found, pairing is complete.

After restoring factory settings, any previously manually set data will revert to factory defaults.

5.3. Common Issues and Solutions

  • Monitor not charging via solar: Ensure the solar panel is exposed to direct sunlight. If not, use the USB charging cable.
  • Sensor not working or showing incorrect values: Try re-pairing the sensor as described in section 5.1. For external sensors, replace the battery (CR1632). For built-in sensors, professional inspection or replacement may be needed.
  • Screen turns off after 5 minutes: This might be the intelligent on/off feature. The monitor turns off when stationary and turns on with vibration. If it's not turning on with movement, ensure it's charged.
  • Monitor beeps continuously: Check the tire pressure and temperature readings against the set limits. Adjust limits if necessary (sections 3.3, 3.4).
  • Air pressure display not accurate: While the system is designed for accuracy, some users report minor offsets. The manual does not provide a manual calibration for delta correction. Ensure sensors are correctly installed and tires are properly inflated.

6. Specifications

FeatureSpecification
Model NameK01/K02
Brand NameE-ACE
Item TypeAlarm Systems & Security
Voltage5V
Special FeaturesSolar Energy
External Testing CertificationCE
CertificationRoHS, FCC, ECE, CE
Is Batteries IncludedYes
High-concerned chemicalNone
Working Temperature (Built-in Sensor)-40℃ to 125℃
Working Temperature (External Sensor)-20℃ to 80℃
Battery Life (Built-in Sensor)5 Years (non-replaceable)
Battery Life (External Sensor)2 Years (replaceable CR1632)
IP RatingIP67 (Waterproof/Dust-proof)
Pressure Range0-3.5 Bar / 0-50 PSI
Frequency433.92 MHz
External Sensor Specifications and Dimensions

Image: External Sensor Specifications and Dimensions, including working voltage, temperature, pressure accuracy, frequency, pressure rate, temperature rate, temperature accuracy, and battery life.

Built-in Sensor Specifications and Dimensions

Image: Built-in Sensor Specifications and Dimensions, including working voltage, temperature, pressure accuracy, frequency, pressure rate, temperature rate, temperature accuracy, and battery life.

7. Warranty and Support

7.1. Product Certifications

The E-ACE TPMS system holds several important certifications, ensuring its quality and compliance with international standards.

Qualification Certifications for E-ACE TPMS

Image: Certificates of Compliance for CE, FCC, and RoHS standards.

7.2. Additional Support

For further assistance or detailed information, please refer to the comprehensive user manual available in PDF format. A link to the PDF manual is provided by the seller: E-ACE TPMS User Manual (PDF).

The product comes with a 365-day free replacement policy, offering maximum security for your purchase.

8. User Tips

  • Initial Charge: Always ensure the monitor is fully charged via USB for 3-4 hours before first use, especially if it doesn't turn on immediately after unboxing.
  • Sensor Security: If using external sensors, consider additional anti-theft measures or secure caps, as they can be prone to theft in some areas.
  • Professional Installation: For built-in sensors, professional installation is highly recommended to ensure accuracy, stability, and proper wheel balancing.
  • Troubleshooting Sensors: If a sensor stops working or shows incorrect values, first try re-pairing it with the monitor. For external sensors, replacing the CR1632 battery is a common solution.
  • Vehicle Compatibility: This device is suitable for a wide range of vehicles including cars, SUVs, ORVs, MPVs, Minibuses, and Wagons.
  • Display Units: The display units for pressure (BAR/PSI) and temperature (°C/°F) can be easily configured in the settings menu to match your preference.
  • Trailer Use: While designed for cars, some users find it useful for trailers. However, verify the signal range is sufficient for your specific trailer length.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.