1. Introduction
Thank you for purchasing the LEHX L6Pro Android 14 Car Radio. This manual provides detailed instructions for installation, operation, and troubleshooting to ensure optimal performance and a safe driving experience. Please read this manual thoroughly before use.
Important Note: Before installing, please test the unit to ensure it is functioning correctly, as long journeys may affect the product. Do not install the product directly into your car without prior testing.
A PDF version of this manual is available for download. Please refer to the seller's product page for the link.
2. Vehicle Compatibility
This car radio is designed for specific vehicle models. Please ensure your car's center panel matches the compatible design shown below. If your original radio has an incompatible panel, do not purchase this product.


3. Setup and Installation
It is recommended that installation be performed by professionals to avoid damage to the car dashboard or the device.
3.1. Rear Interface Description (Power Plug)
The main power plug connections are as follows:
| Wire Color | Function |
|---|---|
| White | Front speaker L |
| White/black striped | Front speaker R |
| Gray | Rear speaker L |
| Gray/black striped | Rear speaker R |
| Green | Rear speaker L |
| Green/black striped | Rear speaker R |
| Purple | Rear speaker L |
| Purple/black striped | Rear speaker R |
| Black (thick) | GND (Ground Wire/B-) |
| Yellow | BATTERY (Constant Power Supply +12V) |
| Red | ACC (Ignition Switch) |
| Orange | ILLUMINATION (Illuminate Backlight) |
| Pink | REVERSE (Reversing camera control line) |
| Brown | KEY2 (Steering Wheel Control-2) |
| Orange/black striped | KEY1 (Steering Wheel Control -1) |
| Blue | ANT (Auto Antenna Power) |
Notes on Power Connections:
- When the yellow line B+ and the red line ACC have a 12V positive power at the same time, the unit can be turned on normally.
- The yellow line B+ keeps the power on and the machine has a memory function.
- For speaker cables: Each cable cannot be grounded, cannot be shared, and cannot touch other lines. Otherwise, there will be no sound output, output sound distortion, or machine overheating.
3.2. Other Rear Connections
Additional connections include:
- F-CAM(VIDEO-IN-2): Video Input 2 (Front Camera Input)
- AUX R IN: Right Audio Input
- AUX L IN: Left Audio Input
- VIDEO-IN-1: Video Input 1
- VIDEO OUT: Video Output
- FR OUT: Front Right Audio Output
- FL OUT: Front Left Audio Output
- SUB WOOF: Subwoofer Output
- MIC: Microphone Input
- AMP CONT: Amplifier Control
- BT Antenna
- R-CAM: Reversing Camera Input
- WiFi Antenna
- USB1/2: USB Port
- Protocol Box: Use only when needed.

3.3. Reversing Camera Installation
Follow these steps to install the reversing camera:
- Find the accessories: 1 camera + 1 power cord + 1 video cable.
- Locate the wiring port: Find the reverse control line (pink) on the unit's power line and connect it to the positive 12V pole. The screen will turn blue. Then, find the CAM video input interface at the back of the unit, and locate the positive and negative terminals of the backup light.
- The camera has two sockets: The red socket connects to the power cable, the yellow to the video cable. The red wire of the power cable and the video cable are screwed together on the positive pole of the reverse lamp. The black wire of the power cable is not used. The other end of the video cable connects to the CAM video input interface at the back of the unit. The red line from the video line connects to the reversing control line of the power line.
Important: If the reversing camera is not installed, do not connect the REVERSE/BACK cable to any location. Leave it unconnected. Otherwise, the unit may not display properly or may automatically enter reverse mode, leading to malfunction. If this occurs, disconnect the REVERSE/BACK line immediately.


3.4. CANBUS Connection
The CANBUS system allows communication between the car radio and your vehicle's systems.
- For high-end model cars: Disconnect the existing connection and connect the CANBUS box.
- For low-end model cars: Connect the CANBUS box and disconnect the existing connection.
Attention: If the CANBUS box and black buckle are connected simultaneously, it may cause the radio to fail to shut down after the car is turned off.
4. Operating Instructions
4.1. Learning Steering Wheel Controls
To configure your steering wheel controls:
- Press and hold a button on the original car's steering wheel.
- Find the corresponding button icon on the car radio's interface.
- Click the icon to change its color, indicating successful learning.

4.2. Apple CarPlay and Android Auto
The LEHX L6Pro supports both Apple CarPlay and Android Auto for seamless smartphone integration.
Wired Connection:
Simply connect your USB data cable to the car radio, and it will automatically enter the CarPlay or Android Auto interface.
Wireless Connection:
- First, enable Bluetooth and Wi-Fi functions on your mobile phone.
- Connect your phone to the car radio via Bluetooth.
- The system will automatically enter the CarPlay or Android Auto interface. (Note: The signal is transmitted via Wi-Fi, so it will function normally even if Bluetooth is turned off. If Wi-Fi is turned off, the connection will be disconnected.)
Android Auto Specifics: This feature may not be supported in all countries, and Google Play services must be available locally. You need to download and install the Android Auto app from Google Play and use a mobile phone with Android 6.0 or higher with a valid data cable connection.

4.3. Key Features and Functions
- Split Screen: Use two applications simultaneously on the screen.
- Adjustable Button Color: Customize the color of the physical buttons on the unit.
- Offline/Online GPS Navigation: Pre-installed offline maps with free updates. Supports Waze, Navitel, Yandex, and IGO.
- Voice Control: Control various functions using voice commands (e.g., "Close navigator," "Turn off the radio," "Open music").
- Bluetooth 5.1: Built-in smart Bluetooth system for mobile phone pairing, music streaming, and hands-free calling.
- DSP (Digital Sound Processor): Provides higher-level stereo surround sound with DTS HiFi digital audio authorization, Trubass, and Phantom Center modes.
- 4G LTE & Dual SIM: Supports 4G internet connectivity with an external SIM card slot, allowing for two SIM cards (integrated and external).
- ADAS DVR Support: Provides 1080P video recording and clear night image quality, with reminders for front collision and lane departure.
- TPMS (Tire Pressure Monitoring System) Support: Real-time temperature visualization and immediate alarms if tire pressure or temperature limits are exceeded.
- DAB+ Tuner Ready: Enjoy high-quality digital audio broadcasting with an optional DAB+ radio receiver stick connected via USB.
- Video Output: 4-core models support headrest connection video output. 8-core models do not support rear view headrests directly but can with additional USB adapters.










5. Maintenance
- Screen Cleaning: Use a soft, lint-free cloth to gently wipe the screen. Do not use harsh chemicals or abrasive materials.
- Software Updates: Periodically check for software updates to ensure optimal performance and access to new features. Updates may change existing functions without prior notice.
- General Care: Keep the unit free from dust and moisture. Avoid exposing it to extreme temperatures.
6. Troubleshooting
This section addresses common problems and provides solutions.
6.1. Cannot Boot Normally
- Wiring Check: Ensure the yellow (B+), red (ACC), and black (GND) wires are correctly connected to the positive, key control, and negative poles, respectively. Incorrect or incomplete connections will prevent booting.
- Color Mismatch: Do not connect the original car lines and unit wiring by color alone, as car line colors may not be standard. Incorrect connections can cause damage.
- Original Car Plug: The original car plug cannot be directly plugged into the new unit. Even if it fits, it may not work or could cause damage.
- Fuse Check: If the 3 wires are connected correctly but the unit doesn't boot, check the fuse on the yellow line. If the fuse is intact, twist the yellow and red wires together, turn on the key, and press the power button.
- Repeated Fuse Burning: If the fuse burns repeatedly, it indicates a short circuit in the unit's protection circuit. Do not replace the fuse again. The unit may require professional repair. To confirm, connect the yellow and red wires to a 12V battery (positive) and the black wire to negative. If it boots, the car's wiring is faulty. If not, the unit is broken.
6.2. Automatic Shut-down
- Cable Error: If the blue cable (automatic antenna power supply) is connected to the unit's power cable, an automatic shutdown will occur. Follow correct wiring methods.
- Unstable Voltage: Find a 12V-5A power supply and re-test. If the unit still shuts down, replace the power supply. If it continues to shut down, the unit is faulty.
6.3. Noise Issues
- Low Speaker Power: If the original speaker power is too low, noise may occur when the volume is turned up. Solution: Keep the volume moderate when replacing speakers or listening to music.
- Grounded Speaker Cable: If a speaker cable is grounded, connect the iron speaker cable directly to the unit's speaker cable.
6.4. Remote Control Not Working
- Test Method: Use your mobile phone camera to check the remote control's infrared light. If the light doesn't illuminate when a button is pressed, replace the battery. If it illuminates, the remote control is functional.
6.5. Settings Not Saved (No Memory)
- Wiring Check: Ensure the yellow and red lines are connected correctly (yellow to positive, red to key control).
- Reversed Wires: If yellow and red wires are reversed, simply switch their positions.
6.6. Bluetooth Not Working
Turn on the unit, search for its Bluetooth name on your mobile phone, and click "Connect." After connecting, you should be able to answer calls or play music via Bluetooth.
6.7. Product Emits Smoke
Replace the FUSE. If the problem persists, the internal circuit is likely burned, and after-sales service is required.
6.8. Sound Cannot Be Adjusted
- Reset the unit or unplug and replug the power cord.
- If the volume knob is broken, it needs to be replaced.
6.9. Reversing Camera Does Not Display
- Wiring Issues: Check for wrong or missing wiring. Refer to section 3.3 for correct connection methods.
- Faulty Camera: If the camera's light does not illuminate when properly wired, the camera is broken and needs replacement.
6.10. USB Devices Cannot Be Played
Format the USB flash drive to FAT32. Re-download one or two songs and try again. If it still doesn't work, replace the USB flash drive.
6.11. FM Radio Station Not Received
- Antenna Connection: Ensure the antenna plug is fully inserted and the antenna line is not disconnected.
- Station Search: Use the "AS" button to automatically search for stations, or manually search using the "before" or "after" buttons.
- Antenna Replacement: If the above steps don't work, unplug the antenna plug and try inserting a screwdriver or metal strip in its place to test.
6.12. No Sound Immediately After Installation
If there is no sound after installation, it is usually due to a wiring error or a short-circuited original car speaker wire. Follow these steps:
- Check if the speaker cable is short-circuited and re-connect if necessary.
- Verify the number of speaker cables. If your original car line has only 2 speaker cables and does not match the unit's requirements, you need to re-route the original car line. One speaker requires 2 speaker wires; 2 speakers require 4 speaker cables.
6.13. No Sound After A While
Disconnect all speaker cables from the unit (do not remove them). Find an external speaker and connect it to the gray and purple wires of the tail line. Connect any group to green and check for sound. If there is sound, the car's speaker line is short-circuited or the speaker is damaged. If there is no sound, the unit is broken.
7. Specifications
The LEHX L6Pro car radio comes in various configurations. Below are the general specifications and model-specific details:
7.1. General Specifications
| Feature | Specification |
|---|---|
| Operating System | Android 14 |
| Display Size | 10.1" |
| Resolution | QLED 1280*720 |
| Din Type | Double Din |
| Out Power | 50x4 |
| Voltage | 12 V |
| Item Weight | 1.7kg |
| Item Size | 255mm-151mm |
| Max External Memory | 128G |
| Material Type | ABS+ |
| Certification | CE |
| Built-in DVD Player | No |
| Built-in CD Player | No |
| Touch Screen | Yes |
| Built-in Screen | Yes |
| TF/Micro SD Slot | 0 |
| Special Features | WiFi, Steering Wheel Control, 4G Network, Built-in GPS, Mobile Phone, MP3 players, Voice Control, DSP, CarPlay, Android Auto, Reversing Input, Split Screen |
| Digital Media Format | CD, DVD-R/RW, DVD-RAM, VIDEO CD, Mp3, MP4, WMA, JPEG |
| OSD Language | Multi-language support including English, Spanish, Russian, French, German, Italian, etc. |
| Subwoofer Output | Support |
| GPS Navigation Map | Built-in offline map free update (support Navitel/Igo) |
| Rear View Camera Input | Support (Free Gift) |
| Mirror Link | Iphone & Android |
| AV-OUT | WiFi version support, 4G version not support |
| WIFI | Built-in |
| Interface | 2*USB RCA Bluetooth |
| RCA Cable | 7 channels including subwoofer cable |
| Steering Wheel Control | Support |
| Microphone | Built-in |
| External Microphone | Optional |
| Bluetooth Phone Book | Support |
| Bluetooth Music | Support |
| Antenna Adapter | Included |
7.2. Model Variants
| Model | CPU | RAM/ROM | Connectivity | Features |
|---|---|---|---|---|
| LQ | UIS8141 4 Core | 1GB RAM / 32GB ROM | WIFI H2.4G, Bluetooth 5.0 | ASP, 2*USB ports |
| L6X | UIS8141 4 Core | 2GB RAM / 32/64GB ROM | WIFI H2.4G, Bluetooth 5.0 | ASP, 2*USB ports, Wireless Carplay + Android AUTO |
| L6 Plus | 9863/UIS8581 64BIT 8 Core | 2GB RAM / 32GB ROM | WIFI 5G, Bluetooth 5.3 | HIFI DSP, 2*USB ports |
| L7Plus | 9863/UIS8581 64BIT 8 Core | 2/4GB RAM / 32/64GB ROM | 4G LTE, WIFI 5G, Bluetooth 5.3 | ASP, 2*USB ports, Wireless Carplay + Android AUTO |
| L5 Pro | 9863/UIS8581 64BIT 8 Core | 2/4GB RAM / 32/64GB ROM | 4G LTE, WIFI 5G, Bluetooth 5.3 | HIFI DSP, 2*USB ports, Wireless Carplay + Android AUTO |
| L6 Pro | 7862 64BIT 8 Core | 4/6GB RAM / 32/64/128GB ROM | 4G LTE, WIFI 5G, Bluetooth 5.3 | HIFI DSP, 3*USB ports, Wireless Carplay + Android AUTO |

8. User Tips
- Professional Installation: It is highly recommended to have the unit installed by professionals to prevent damage to your car or the device.
- CANBUS Configuration: If your order includes a CANBUS module, ensure you set the correct CANBUS type in the settings for proper button functionality. Contact customer service for assistance if needed.
- Google Services: Google Play services may not be available in all countries. Check local availability if this is a critical feature for you.
- Boot Logo: To change the boot logo, navigate to Configuration > Car Information > General > Boot Logo. Use password L6/L6Plus 8888 or L6Pro 3368, then select your desired logo.
- Satellite Signal: After the first successful search for satellite signals, the time and date will be updated automatically.
- Memory Usage: Be aware that the operating system and pre-installed applications will consume a portion of the device's memory. For example, the map of Russia requires about 2.8GB, and the map of Europe requires about 6.8GB.
9. Warranty and Support
9.1. Warranty
The LEHX L6Pro Car Radio comes with a 1-year warranty.
9.2. Customer Support
If you encounter any questions or issues with the product, delivery, or service, please contact LEHX customer service. We are committed to providing prompt assistance.
You can also find support and community information through the following channels:



For additional support, you can scan the following QR codes:
