1. Introduction
Thank you for choosing the ANDELI MIG-270 Multifunctional Professional Welding Machine. This 3-in-1 inverter welder is designed for versatility and ease of use, supporting MIG (CO2/MIX/FLUX), Lift TIG, and MMA welding processes. It features synergic control for intuitive operation and is capable of welding various materials, including aluminum, carbon steel, and stainless steel.
This manual provides essential information for the safe and efficient operation, setup, maintenance, and troubleshooting of your MIG-270 welding machine. Please read it thoroughly before using the equipment.

Figure 1: ANDELI MIG-270 Welding Machine
2. Safety Information
WARNING: Welding can be dangerous. Always follow safety precautions to prevent injury or death.
- Electric Shock: Can kill. Do not touch live electrical parts. Wear dry, insulating gloves and protective clothing. Ensure the workpiece is properly grounded.
- Fumes and Gases: Can be hazardous to your health. Keep your head out of the fumes. Use enough ventilation or exhaust at the arc to keep fumes and gases away from the breathing zone.
- Arc Rays: Can burn eyes and skin. Wear a welding helmet with a proper shade of filter lens to protect your face and eyes when welding or watching. Wear safety glasses with side shields under your helmet. Wear protective clothing made from durable, flame-resistant material.
- Fire and Explosion: Welding sparks and hot metal can cause fires and explosions. Keep flammable materials away from the welding area. Have a fire extinguisher nearby.
- Burns: Hot metal can cause severe burns. Do not touch hot parts with bare hands.
- Overheating Protection: The machine is equipped with automatic protection against overheating. If the machine overheats, it will shut down temporarily. Allow it to cool before resuming operation.
- Ensure the machine is connected to a power supply that matches its voltage requirements (110V/220V).
- This product is CE certified, indicating compliance with European safety standards.
3. Package Contents
The standard package for the MIG-270 welding machine typically includes the following items. Please verify all components upon receipt.

Figure 2: Typical Package Contents
- ANDELI MIG-270 Welding Machine
- Ground Clamp (2M)
- MMA Holder (3M)
- 15AK MIG Torch (3M)
- Wire Feeding Tube
- WP-17V TIG Torch (4M)
- Gas Pipe (3M)
- W Wire Feed Roller
- U Wire Feed Roller
- Welding Rods (5 pcs)
- Brush
- Tungsten Electrodes (10 pcs)
- 15AK Nozzles (10 pcs)
- Nozzle Shield (2 pcs)
- Collets (10 pcs)
- Flux-cored Wire
4. Product Overview
The ANDELI MIG-270 is a versatile welding machine offering MIG, Lift TIG, and MMA functionalities. Its user-friendly control panel and synergic design make it suitable for both beginners and experienced welders.
4.1. Key Features
- 3-in-1 Functionality: Supports MIG (Gas/Gasless), Lift TIG, and MMA welding.
- Dual Voltage: Operates on 110V or 220V power supplies, offering flexibility.
- Synergic Control: Automatically adjusts voltage and wire feeding speed based on amperage or material thickness, simplifying setup.
- Aluminum Welding Capability: Can weld aluminum, compatible with a spool gun or MIG torch with a graphite wire feed tube.
- IGBT Inverter Technology: Ensures high efficiency, reliability, and a strong 200A output current.
- Safety Features: Includes automatic protection against overheating and over-current/voltage.

Figure 3: Key Features of MIG-270
4.2. Control Panel Introduction
The control panel is designed for intuitive operation. Refer to the diagram below for a detailed explanation of each control and indicator.

Figure 4: Control Panel Layout
- Gas Checking: Indicator for gas flow status.
- MIG/Synergy MIG/MMA/TIG Selection: Buttons to select the desired welding mode.
- MIG Parameter (CO2/MIX/Flux): Buttons to select MIG gas type or flux-cored wire.
- Aluminium Welding: Indicator for aluminum welding mode.
- Wire Checking: Indicator for wire feed status.
- 2T/4T: Toggle for 2-stroke or 4-stroke trigger operation.
- Spot Welding: Indicator for spot welding function.
- Welding Wire Diameter: Selection for wire diameter (1.0, 0.9, 0.8, 0.6 mm).
- Digital Displays: Show current welding parameters (Voltage/Amperage).
- Adjusting Knobs: For fine-tuning voltage and amperage.
5. Setup Instructions
Proper setup is crucial for safe and effective welding. Follow these steps carefully:
5.1. Power Connection
- Ensure the welding machine is turned off before connecting to power.
- Connect the power cord to a suitable 110V or 220V power outlet, depending on your machine's configuration and local power supply. The machine automatically detects voltage.
5.2. Ground Clamp Connection
- Connect the ground clamp cable to the negative (-) terminal on the front panel of the machine.
- Securely attach the ground clamp to the workpiece or a sturdy metal workbench that is properly grounded. Ensure good electrical contact.
5.3. MIG Welding Setup (Gas/Gasless)
- MIG Torch: Connect the MIG torch to the designated connector on the front panel.
- Wire Spool Installation: Open the side panel of the machine. Install the appropriate welding wire spool (e.g., flux-cored for gasless, solid wire for gas MIG). Ensure the wire feed roller matches the wire diameter.
- Wire Feeding: Thread the welding wire through the wire feed mechanism and into the MIG torch liner. Press the wire feed button (if available) or trigger the torch to feed the wire until it exits the nozzle.
- Gas Connection (for Gas MIG): Connect the gas pipe from your shielding gas cylinder (CO2 or Argon/CO2 mix) to the gas inlet on the rear of the machine. Ensure the gas regulator is properly installed and set to the recommended flow rate.
- Nozzle and Contact Tip: Ensure the correct contact tip and nozzle are installed on the MIG torch for your wire diameter and welding process.
5.4. Lift TIG Welding Setup
- TIG Torch: Connect the WP-17V TIG torch to the appropriate terminal (usually negative for DC TIG) on the front panel.
- Gas Connection: Connect the gas pipe from your Argon shielding gas cylinder to the gas inlet on the rear of the machine.
- Tungsten Electrode: Install a sharpened tungsten electrode of the correct size into the TIG torch collet.
5.5. MMA (Stick) Welding Setup
- MMA Holder: Connect the MMA electrode holder cable to the positive (+) terminal on the front panel.
- Electrode: Insert the appropriate welding electrode into the holder.
6. Operating Instructions
Before operating, ensure all safety precautions are observed and the machine is correctly set up for your chosen welding process.
6.1. General Operation Steps
- Turn on the welding machine using the power switch.
- Select the desired welding mode (MIG, MMA, or TIG) using the buttons on the control panel (refer to Figure 4, item 2).
- Adjust welding parameters (voltage, amperage, wire feed speed) using the adjusting knobs and digital displays. For MIG, select the gas type (CO2/MIX/FLUX) and wire diameter (Figure 4, items 3 & 8).
- Perform a test weld on scrap material to fine-tune settings before welding your actual workpiece.
6.2. MIG Welding (Gas/Gasless)
The MIG-270 supports both gas-shielded MIG and gasless flux-cored welding. It features synergic control for easier parameter setting.

Figure 5: MIG Welding Process and Weld Types
- Synergic Control: When enabled, adjusting the amperage knob will automatically adjust the voltage and wire feed speed for optimal welding.
- 2T/4T Function:
- 2T (Two-Touch): Press and hold the torch trigger to start welding; release to stop.
- 4T (Four-Touch): Press and release the trigger to start welding; press and release again to stop. This is useful for longer welds to reduce hand fatigue.
- Aluminum Welding (AL Welding): Select the aluminum welding mode. Ensure you use a graphite wire feed tube in your MIG torch and appropriate aluminum welding wire. The machine is suitable for aluminum welding with thicknesses of approximately 2-4mm.

Figure 6: Aluminum Welding

Figure 7: Aluminum Welding Effect (Pulse Options)
6.3. Lift TIG Welding
For precise welding of iron and stainless steel.

Figure 8: Lift TIG Welding
- Select TIG mode.
- Ensure Argon gas is flowing.
- Touch the tungsten electrode to the workpiece to initiate the arc (Lift Arc), then lift slightly to maintain the arc.
6.4. MMA (Stick) Welding
For general-purpose welding with coated electrodes.

Figure 9: MMA Welding
- Select MMA mode.
- Strike the electrode against the workpiece to initiate the arc.
- Maintain a consistent arc length and travel speed.
7. Maintenance
Regular maintenance ensures the longevity and optimal performance of your welding machine.
- Cleaning: Regularly clean the machine's exterior with a dry cloth. Use compressed air to blow out dust and debris from inside the machine, especially from cooling vents, at least once a month or more frequently in dusty environments.
- Cable Inspection: Check all welding cables, power cords, and gas hoses for cuts, fraying, or damage before each use. Replace damaged components immediately.
- Torch Maintenance:
- MIG Torch: Clean the nozzle, replace worn contact tips, and check the wire liner for blockages or wear.
- TIG Torch: Inspect the tungsten electrode for proper sharpening and replace if contaminated or too short. Check collets and collet bodies.
- MMA Holder: Ensure good contact with the electrode and check for damage.
- Wire Feed System (MIG): Clean the wire feed rollers and guide tubes. Ensure the rollers are free of debris and correctly tensioned for the wire being used.
- Storage: Store the machine in a clean, dry environment when not in use.
8. Troubleshooting
This section addresses common issues you might encounter. For problems not listed here, contact customer support.
| Problem | Possible Cause | Solution |
|---|---|---|
| Machine does not power on | No power supply; Power switch off; Faulty power cord. | Check power outlet and circuit breaker; Ensure power switch is ON; Inspect power cord for damage. |
| No welding arc | Poor ground connection; Incorrect welding mode selected; Incorrect parameters; Damaged torch/electrode holder. | Ensure ground clamp has good contact; Select correct mode; Adjust parameters; Inspect and replace damaged parts. |
| Wire not feeding (MIG) | Wire spool tangled; Wire feed roller tension incorrect; Contact tip blocked; Liner clogged. | Untangle wire; Adjust roller tension; Clean/replace contact tip; Clean/replace liner. |
| Poor weld quality | Incorrect parameters; Improper technique; Contaminated workpiece; Wrong shielding gas (MIG/TIG). | Adjust voltage/amperage/wire speed; Practice technique; Clean workpiece; Verify gas type and flow rate. |
| Machine overheats (shuts down) | Exceeded duty cycle; Blocked cooling vents; High ambient temperature. | Allow machine to cool down; Ensure proper ventilation; Clean cooling vents. |
9. Specifications
Technical parameters for the ANDELI MIG-270 welding machine:

Figure 10: MIG-270 Technical Specifications
| Parameter | MIG-270 Value |
|---|---|
| Power Supply Voltage (V) | 220 (Dual Voltage 110V/220V compatible) |
| Frequency (Hz) | 50 |
| Function | MIG, MMA, LIFT TIG |
| Rated Input Power (KW) | MIG: 5.9, MMA: 6, LIFT TIG: 4.4 |
| Rated Input Current (A) | MIG: 26.8, MMA: 27.7, LIFT TIG: 20.1 |
| Effective Input Current (A) | MIG: 9.4, MMA: 10.7, LIFT TIG: 7 |
| Welding Current Range (A) | MIG: 30-180, MMA: 20-160, LIFT TIG: 30-180 |
| Load Voltage (V) | MIG: 23, MMA: 26.4, LIFT TIG: 17.2 |
| No-Load Voltage (V) | 62 |
| Efficiency (%) | 85% |
| Power Factor | 0.93 |
| Protection Class | IP21S |
| Insulation Class | H |
| Cooling | Fan |
| Dimension (MM) | 490×200×320 |
| Net Weight (KG) | 10 |
10. User Tips
- Accessory Check: Always confirm all necessary accessories (torches, clamps, wires, gas) are present and correctly connected before starting any welding task.
- Synergic Mode for Beginners: Utilize the synergic control feature, especially if you are new to welding, as it simplifies parameter adjustments.
- Aluminum Welding Prep: When welding aluminum, ensure your MIG torch has a graphite wire feed tube to prevent wire feeding issues.
- Practice Makes Perfect: Always practice on scrap material to get a feel for the machine and fine-tune your settings for the specific material and thickness you are working with.
- Ventilation: Always ensure adequate ventilation in your welding area to disperse fumes and gases.
11. Warranty and Support
ANDELI provides a two-year warranty for the MIG-270 welding machine. In case of any issues or for free guidance, please contact the efficient customer service team. They offer returns and exchanges within 30 days of receiving the goods, and free replacement of parts under warranty.
For technical support or warranty claims, please refer to the contact information provided by your seller or on the official ANDELI website.