PZEM-008 Din Rail Electricity Digital Power Energy Meter User Manual

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of the PZEM-008 Din Rail Electricity Digital Power Energy Meter. This device is designed to measure AC voltage, current, active power, and energy consumption, displaying the data on an LCD screen. Please read this manual thoroughly before use and retain it for future reference.

2. Important Safety Instructions

Before using this product, read and understand all instructions in this manual. Retain this manual for future reference.

Intended Use:

This product is for household use only. Use only as described in this manual.

Product Condition:

Do not use the product if it is damaged in any way.

User Suitability:

This product is intended for persons aged 18 years and above. It may be used by persons with reduced physical, sensory or mental capabilities, or lack of experience/knowledge, only if they are supervised or instructed on safe use and understand the hazards involved.

WARNING: Electrical work should only be performed by qualified personnel. Ensure power is OFF before installation or maintenance.

3. Product Overview

The PZEM-008 is a compact digital power energy meter designed for DIN rail mounting. It features a BTN wide viewing angle LCD for clear display of multiple parameters.

3.1. Display Interface

The LCD displays Voltage, Current, Active Power, and Energy simultaneously. A 'CLR' key is present for control functions.

4. Specifications

4.1. Dimensions

5. Setup and Installation

The PZEM-008 is designed for 35mm DIN rail mounting. Ensure all power is disconnected before proceeding with installation.

5.1. Wiring Instructions

This meter features a built-in current transformer (CT) for no-screw wiring, helping to avoid poor contact and heating issues. It is a single-phase meter.

General Wiring Steps:

1. Turn off Power: Before any wiring, ensure the main power supply is completely off.
2. Mount the Meter: Securely lock the PZEM-008 onto the 35mm DIN rail.
3. Connect L Line through CT: Take the Live (L) line from your main switch and pass it through the current transformer (CT) ring of the PZEM-008.
4. Connect L Line to Meter: Connect the Live (L) line from the PZEM-008's terminal to the main switch, ensuring it's connected with the same L line that passed through the CT ring.
5. Connect N Line: Connect the Neutral (N) line from the PZEM-008's terminal to the main switch's Neutral (N) line.
6. Tighten Connections: Ensure all screws are securely tightened to prevent loose connections.
7. Restore Power: After verifying all connections are correct and secure, turn on the main power supply.

Note:

• You do not need to distinguish between the Neutral (N) or Live (L) line when passing it through the CT ring. Either line can go through the ring.
• However, do NOT pass both the N and L lines together through the CT ring. Only one line should pass through.
• The measurement voltage and ampere shall not exceed the calibration range.
• Make sure the wiring is correct before powering on.

Wiring Diagrams:

Video Demonstration:

Video: A demonstration of the wiring process for the PZEM-008 meter in an electrical box.

6. Operation

The PZEM-008 measures AC voltage, current, active power, and energy, displaying them on its LCD screen.

6.1. Display Instructions

• Voltage: Measurement range AC50-300V. Starting test voltage: 50V. Accuracy: ±1%.
• Current: Measurement range 0-100A. Display format: <10A as 9.99A, <100A as 99.9A. Starting test current: 0.02A. Accuracy: ±1%.
• Active Power: Measurement range 0-30kW. Display format: <10W as 9.99W, <100W as 99.9W, <1000W as 999W, <10000W as 9.99kW, ≥10000W as 30.0kW. Starting test power: 0.5W. Accuracy: ±1%.
• Energy: Measurement range 0-1999kWh. Display format: <10kWh as 9.99kWh, <100kWh as 99.9kWh, <1000kWh as 999kWh, <10000kWh as 1999kWh. Over the test range, the data will be maintained; otherwise, you reset it. Accuracy: ±1%.

6.2. Other Functions

• Backlight Control: The backlight can be turned on or off by a short press of the 'CLR' key.
• Reset Energy: Long press the 'CLR' key for over 3 seconds until the energy data flashes. Then, release the key and short press it again to reset the energy. If you do not short press again within 3 seconds, it will stop flashing, and the energy will not be reset.
• Data Storage: When the power is off, the energy data and backlight status are automatically saved.

7. Maintenance

• Keep the device clean and dry.
• Avoid exposing the device to extreme temperatures or humidity.
• Do not attempt to open or repair the device yourself. Refer to qualified service personnel.
• Ensure all connections remain tight and secure.

8. Troubleshooting

If the device is not displaying readings or functioning correctly, please check the following:

• No Display: Verify that the power supply is connected correctly and is within the specified voltage range (AC50-300V).
• Incorrect Readings: Ensure the wiring is correct, especially that only one Live (L) or Neutral (N) line passes through the CT ring, not both. Check that the measurement range is not exceeded.
• Energy Not Resetting: Follow the 'Reset Energy' procedure carefully (long press, release, then short press the 'CLR' key).

If problems persist, consult the manufacturer or a qualified electrician.

9. User Tips

• The PZEM-008 is supplied as a single unit.
• This meter is specifically designed for DIN Rail Mounting, making it easy to integrate into existing electrical panels.

10. Warranty and Support

Manufacturer Information:

Manufacturer: Shenzhen Pingtudi Electronic Technology Co., Ltd.
Address: Building A, Jianye Tai Industrial Zone, No. 11 Minhuan Road, Longhua District, Longhua Street, Shenzhen, Guangdong, CN (China)

Certifications:

This product is CE and FCC certified, indicating compliance with relevant European and US safety and performance standards.

Additional Documentation:

A comprehensive user manual in PDF format is available for download: View User Manual (PDF)