1. Introduction and Safety Warnings
1.1 Preface
Thank you for purchasing this product, which is a dual band/dual display/dual watch walkie talkie. This easy-to-use radio is designed to provide secure, instant, and reliable communications. Please read this manual carefully before use to ensure maximum performance and safe operation. This product is a Certified Original BAOFENG device.
1.2 Regulations and Safety Warnings
WARNING!
- European Users: Operation in Transmit mode requires a valid Amateur Radio License. Failure to comply may be unlawful. Refer to EU specification guide 2014/53/EU.
- When programming the radio, always read factory software data first, then rewrite.
- Before using, read the RF Energy Exposure and Product Safety Guide for safe usage and compliance.
- Do not operate near fuels, chemicals, explosives, or in blasting areas.
- Avoid operating near medical or electronic equipment vulnerable to RF signals.
- Do not hold the product while driving.
- Do not operate in areas where wireless communication is prohibited.
- Do not use with a damaged antenna. Contact your dealer for replacement.
1.3 Important Tips
- Use only authorized accessories.
- Keep the product at least 2.5 cm from your body during transmission.
- Avoid prolonged high-volume reception.
- Do not place the product in the air bag deployment area in vehicles.
- Keep out of reach of children and pets.
- Operate within the specified temperature range.
- Allow for cooling if continuous transmission causes heat accumulation.
- Handle with care.
- Do not disassemble, modify, or repair without authorization.
1.4 Precautions for Batteries
- Do not charge or replace the battery near fuels, chemicals, or explosives.
- Dry a wet battery with a soft, clean cloth before charging.
- Do not charge a deformed, leaking, or overheated battery.
- Use only authorized chargers.
- Do not charge in areas with strong radiation.
- Do not short circuit battery terminals.
- Do not remove the casing from the battery pack.
- Do not store the battery in unsafe surroundings or throw it into fire.
1.5 Maintenance Instructions
- Clean charging connector dust with a dry cloth regularly.
- Charge the battery between 5°C~40°C (40°F - 105°F).
- Turn off the radio when charging a battery attached to it.
- Do not remove the battery or unplug the power cord during charging.
- Do not dispose of batteries in fire or expose to direct sunlight/heat sources.
- Do not squeeze, penetrate, or remove the battery housing.
- Do not attempt to open or realign the radio; this will void the warranty.
- Avoid storing the radio in direct sunlight, hot areas, or dusty/dirty environments.
2. Main Features
- **Frequency Range:**
- FM Radio: 65-108 MHz (RX)
- AM Aviation Band: 108-136MHz (RX)
- VHF1: 136-174MHz (RX&TX)
- VHF2: 220-260MHz (RX&TX)
- UHF1: 400-520MHz (RX&TX)
- UHF2: 350-390MHz (RX)
- **High Power Output:** 5W-10W, enabling long-distance communication (up to 16 km in open areas).
- **Channels:** Up to 999 memory channels.
- **Display:** 1.44-inch Large LCD Screen with Display Sync (shows channel name, number, and frequency).
- **Charging:** Type-C fast charging (Car, PC, Power Bank, Socket) and traditional desktop charger.
- **Waterproof/Water-Resistant:** IP45 rating.
- **Model Variations:** The K5+ series (including UV-13 PRO) comes in M and L versions. M version supports AM108-136, Police350-390 MHz scanning reception, and voice scrambling. L version does not support these features.
- **Functions:**
- DTMF encoder and manual dial.
- VOX (voice activated transmit) for hands-free operation.
- Alarm function.
- LED flashlight.
- High/low power selectable.
- Programmable repeater offset.
- Transmission time-out timer.
- End of transmission tone ("Roger Beep").
- Dual Watch / Dual Reception.
- Battery save function.
- Busy channel lock out.
- Ten (10) levels of Squelch adjustment.
- Support NOAA weather reception function (US and Canada).
- PC & Manual Programmable.

Figure 1: Key Features of the UV-13 PRO

Figure 2: UV-13 PRO V1 vs V2 Comparison
3. Package Contents
- 1 x Portable Radio
- 1 x Antenna
- 1 x Li-ion Battery Pack
- 1 x Belt Clip
- 1 x The Sling
- 1 x User's Manual (English version)
- 1 x Fast Desktop Charger (Note: Default plug type may vary by region, e.g., EU plug for Russia, Spain, Germany, etc., US plug for USA.)
4. Setup
4.1 Battery Charging
The Li-ion battery pack is not charged at the factory. Please charge it before first use. Full capacity may require two or three charge/discharge cycles. Always use the specified charger.
Charging Procedure:
- Plug the AC adaptor into an AC outlet, then connect it to the DC jack on the back of the desktop charger. The indicator will blink orange.
- Place the battery or the radio (with battery installed) into the charger. Ensure good contact with charging terminals. The indicator will turn red.
- A full charge takes approximately 2-5 hours. The indicator turns green when charging is complete.
- Remove the battery or radio from the charger.
Note: If the radio is powered on during charging, the indicator may not turn green even when fully charged. For accurate indication, turn off the radio while charging.
Type-C USB Charging:
The UV-13 PRO also supports convenient Type-C USB charging.
- Ensure the radio is turned OFF.
- Plug the Type-C USB cable into the charging port on your battery.
- Connect the other end of the cable to a wall power outlet, car charger, PC, or power bank.
- An empty battery will be fully charged in approximately 4 hours.
- The battery meter on the LCD will show charging progress.
Note: It is recommended to power off the radio while charging. For optimal battery life, avoid overcharging and remove the radio from the charger within 6 hours.
LED Indicator Status:
| Status | LED Indication |
|---|
| No Battery | Green and red alternately flashing |
| Charge Normally | Red |
| Fully Charged | Green |
| Trouble (e.g., battery too warm, short-circuited) | Red blinks fast |

Figure 3: Type-C Fast Charging Options
4.2 Accessory Installation
Before installing or removing accessories, ensure the radio is turned off by rotating the power/volume knob counter-clockwise.
Antenna:
- **Installing:** Screw the antenna clockwise into the connector on top of the transceiver until secure.
- **Removing:** Turn the antenna counter-clockwise to remove it.
Belt Clip:
- **Installing:** Remove the two parallel screws above the battery, thread them through the belt clip holes, and screw them back into the radio body.
- **Removing:** Unscrew counter-clockwise.
Battery Pack:
- **Installing:** Align the battery pack in parallel with the radio body, with its lower edge about 1-2cm below the radio's edge. Slide it upward along the guide-rails until it clicks into place.
- **Removing:** Press the battery release above the battery pack and slide the battery downward.
Additional Speaker/Microphone (Optional):
Pry open the rubber MIC-Headset jack cover and insert the Speaker/Microphone plug into the double jack.
5. Radio Overview
Familiarize yourself with the buttons, controls, and display of your UV-13 PRO walkie talkie.

Figure 4: UV-13 PRO Parts Diagram
- **Antenna:** For transmitting and receiving signals.
- **Power/Volume knob:** Rotate clockwise to power on and increase volume; counter-clockwise to decrease volume and power off.
- **Speaker:** Audio output.
- **Microphone:** Audio input.
- **LCD Display:** Two-line display for frequency, channel, and status.
- **MENU Key:** Activates menu, selects options, confirms parameters. Press and hold to switch between VFO and MR modes.
- **Numeric Keypad:** Input frequencies, channel numbers, DTMF codes.
- **EXIT Key:** Exits menu/functions. Press and hold to activate one-touch search.
- **PTT Key (Push-To-Talk):** Press to transmit.
- **Side Key 1 (Broadcast FM/Emergency Alert):** Momentary press for FM receiver; press and hold for alarm function.
- **Side Key 2 (Flashlight/Monitor):** Momentary press for LED flashlight; press and hold to monitor signal (open squelch).
- **TX/RX Status LED:** Red for transmit, Green for receive.
- **LED Flashlight:** Integrated light source.
- **Type-C Charging Port:** For direct USB charging.
- **Type-C Charging Indicator:** Shows charging status.
- **Battery Release Latch:** Releases the battery pack.
5.2 LCD Display Icons
| Icon | Description |
|---|
| RSSI | Squelch Open/Close Indicator |
| H/L | Transmit power level indicator (High/Low) |
| ♪ | DTMF side tone audible |
| D | DCS enabled |
| C | CTCSS enabled |
| + | Repeater access (TX shifted higher than RX) |
| - | Repeater access (TX shifted lower than RX) |
| S | Dual watch enabled |
| 🔒 | Keypad lock enabled |
| VOX | VOX enabled |
| N | Narrowband enabled |
| R | Reverse function enabled |
| SCR | Voice scramble function activated |
Battery Level Indicator: When the battery icon shows empty, the battery is depleted. The radio will beep, flash the display backlight, and announce "Low Voltage" if voice prompts are enabled. Charge or replace the battery.
6. Basic Operations
6.1 Power On/Off
- **To Turn On:** Rotate the Power/Volume knob clockwise until you hear a "click". The radio will emit a double beep and display frequency/channel information.
- **To Turn Off:** Rotate the Power/Volume knob counter-clockwise until you hear a "click".
6.2 Adjusting the Volume
Rotate the Power/Volume knob clockwise to increase volume, and counter-clockwise to decrease volume. Be careful not to turn it too far and accidentally power off the radio.
6.3 Main Band/Sub Band Select
In standby mode, press the [MENU] key to switch between the A (upper) and B (lower) displays. The selected display's frequency or channel becomes active for listening and transmitting.
6.4 VFO/Channel Switch
Press and hold the [MENU] key to toggle between VFO (Frequency) mode and Channel (MR) mode.
- **Channel (MR) Mode:** Displays the channel number.
- **Frequency (VFO) Mode:** Displays 'VFO'.
6.5 Frequency (VFO) Mode
In VFO mode, use the ▲ or ▼ keys to navigate frequencies, or input directly using the numeric keypad. Example: To enter 436.61250 MHz on display A:
- In standby, press and hold [MENU] to switch to VFO mode.
- Enter [4][3][6][6][1][2][5][0] on the numeric keypad.
WARNING! Transmitting on unauthorized frequencies is illegal and can result in serious penalties. Always verify local regulations.
6.6 Channel (MR) Mode and Channel Selection
Channel mode is practical for everyday use with pre-programmed channels.
- Use the ▲ or ▼ keys or the encoder to navigate channels.
- Alternatively, input channel numbers directly using the keypad (e.g., [0][1][2] for channel 12).
6.7 Making a Call
Press [EXIT] to switch the main channel if two channels are displayed.
- **Channel Mode Call:** Select a channel, then hold [PTT] to transmit. Speak into the microphone (2.5-5 cm away). The red LED will illuminate.
- **Frequency Mode Call:** Switch to VFO mode, input the desired frequency, then hold [PTT] to transmit. The red LED will illuminate.
- **Receiving a Call:** Release [PTT]. The green LED will illuminate when receiving.
6.8 Using the Flashlight
Press [SK2] momentarily to turn on the LED flashlight. Press again to flash, and a third time to turn off. The radio operates normally when the flashlight is active.

Figure 5: LED Flashlight in Use
6.9 Emergency Alert
Press and hold [SK1] for 3 seconds to activate the emergency alert (loud siren and flashing flashlight). Press [SK1] again to exit. Use only in genuine emergencies.
6.10 FM Radio (FM)
The radio can receive FM broadcasts from 65-108MHz.
- In frequency or channel mode, press [SK1] to turn on the radio.
- Select the desired frequency with ▲ or ▼ keys, or input directly. Press [#z] to auto-search stations.
- Press [SK1] to exit FM radio.
Note: While listening to FM, the radio will automatically switch to the active frequency/channel mode for normal transmitting/receiving if a signal is detected. It will return to FM mode when the signal disappears.

Figure 6: FM Radio Functionality
6.11 Monitor
In standby, press and hold [SK2] to enter Monitor mode. This opens the squelch to listen to weak signals or matched carriers without signaling. Release [SK2] to return to standby.
6.12 Keypad Lock
To enable/disable keypad lock, press and hold the [*] key for about two seconds. The radio can also be set to automatically lock the keypad after ten seconds via the menu.
6.13 Frequency Reversal
A momentary press of the [*] key enables frequency reversal, swapping transmit and receive frequencies. An "R" will appear on the screen.
6.14 TX Repeaters Tone
Press [PTT] + [SK2] to send a 1750Hz repeater tone. This is useful for accessing repeaters. This function works even with keypad lock enabled.
6.15 One-Touch Frequency Search
The radio acts as a receiver to find active frequencies.
- Press and hold [EXIT]; "SEARCH SEEK..." will display.
- If an effective signal is received, the frequency, CTCSS, or DCS value will be displayed.
- Press [MENU] to save the found frequency/tone to a channel.
Note: During search, press [#z] to switch between UHF/VHF bands.
6.16 Weather Radio/Scan Weather Channel
The radio has a NOAA Weather Radio function for receiving weather reports and scanning NOAA channels.
- Press and hold [OsQL] for 3 seconds to enter Weather band mode.
- Press and hold [#z] for 3 seconds to start scanning all 10 NOAA channels. Press again to stop.
- Manually select channels with ▲ or ▼ keys after stopping scan.
- Press [EXIT] or [PTT] to exit Weather Radio mode.
Note: NOAA channels are receive-only; transmission is not possible.
7. Advanced Features
The menu system allows customization of various radio parameters. Refer to Appendix B (in the full PDF manual) for a complete list of menu items.
- Press [MENU] to enter the menu.
- Use ▲/▼ keys to navigate.
- Press [MENU] again to select an item.
- Use ▲/▼ keys to select a parameter.
- Press [MENU] to confirm and save.
- Press [EXIT] to cancel changes or exit the menu.
Using Short-Cuts:
Each menu item has a numerical value for direct access.
- Press [MENU].
- Enter the menu item number using the keypad.
- Press [MENU] to enter the item.
- Enter the desired parameter using ▲/▼ keys or numerical keypad.
- Press [MENU] to confirm and save.
- Press [EXIT] to cancel or exit.
7.2 Scanning
The Radios features a built-in scanner for VHF and UHF bands. In VFO mode, it scans by frequency steps; in MR mode, it scans channels. Dual Watch is inhibited during scanning.
To Enable/Exit Scanner:
Press and hold [#z] for about two seconds to enable. Press and hold [#z] again to exit.
- **Time Operation (TO):** Scanner stops on a signal, then resumes after a preset time.
- **Carrier Operation (CO):** Scanner stops on a signal, then resumes after a preset time with no signal.
- **Search Operation (SE):** Scanner stops on a signal and remains stopped until [#z] is pressed again.
Frequency Scanning:
In frequency mode, press [#z] for >2 seconds to start. Change direction with ▲/▼. Press [#z] to stop.
Channel Scanning:
In channel mode, press [#z] for >2 seconds to start. Change direction with ▲/▼. Press [#z] to stop.
Allows scanning for frequencies with CTCSS or DCS tones. Not active in Channel mode. Scan starts only when a signal is detected.
7.3 Manual Programming (Channels Memory)
The radio has 999 memory channels. These can store receive/transmit frequencies, power, signaling, bandwidth, and a six-character alphanumeric name.
Programming a Channel Repeater Offset with CTCSS Tone (Example):
To program a new memory in Channel 10 with RX = 432.55000 MHz, TX = 437.55000 MHz (+5 Offset), and TX CTCSS tone 123.0:
- Press [EXIT] to switch menus.
- Press and hold [MENU] to set radio to VFO mode.
- [MENU] [3][1] [MENU] [1][0] [MENU] [EXIT] (Deletes prior data in Channel 10).
- [MENU] [1][2] [MENU] 123.0 [MENU] [EXIT] (Selects desired TX encode tone).
- Enter RX frequency (e.g., 43255000).
- [MENU] [3][0] [MENU] [1][0] [MENU] -> [EXIT] (RX has been added).
- Enter TX frequency (e.g., 43755000).
- [MENU] [3][0] [MENU] [1][0] [MENU] -> [EXIT] (TX has been added).
- Press and hold [MENU] to return to MR mode.

Figure 7: Manual Programming in VFO Mode
7.4 Repeaters Programming
To program repeaters, you need to know the transmit and receive frequencies and be authorized to use them.
- Press and hold [MENU] to set the radio to VFO mode.
- Use the numeric keypad to enter the repeater's output (receiving) frequency.
- Press [MENU] to enter the menu.
- Enter [2][9] for frequency offset.
- Press [MENU] to select.
- Use the numeric keypad to enter the frequency offset.
- Press [MENU] to confirm and save.
- Enter [2][8] for offset direction (positive or negative).
- Use ▲/▼ keys to select + (positive) or - (negative) offset.
- Press [MENU] to confirm and save.
- (Optional) Save to memory or set up CTCSS.
- Press [EXIT] to exit the menu.
7.5 VOX (Voice Activated Transmit)
VOX allows hands-free communication. Speak into the microphone to activate transmission.
- In standby, press [MENU] + 7. "VOX" will display.
- Press [MENU] to enter.
- Use ▲/▼ keys to turn off VOX or select a VOX level (1-10). Level 1 is least sensitive, 9 is most sensitive.
- Press [MENU] to confirm.
- Press [EXIT] to return to standby.
Note: VOX is not enabled in Scan or FM Radio mode.
7.6 Dual Watch
Monitor two channels simultaneously. The radio will flip-flop between two frequencies at a fixed interval.
- Press [MENU].
- Enter 7 for Dual Watch.
- Press [MENU] to select.
- Use ▲/▼ keys to enable or disable.
- Press [MENU] to confirm.
- Press [EXIT] to exit.
7.7 Stopwatch Timer
To use the stopwatch function:
- In standby, press [MENU] + 44. "STOP WATCH" will display.
- Press [MENU] to enter.
- Use ▲/▼ keys to enable (ON). Press [MENU] to confirm.
- Press [MENU] to start counting. Press [MENU] again to restart.
- To exit, stop counting first, then press [EXIT].
7.8 Scrambler
The scrambler protects communications by voice inversion, preventing others from understanding your voice. The "SCR" icon appears when enabled.
- In standby, press [MENU] + 45. "SCRAMBLE" will display.
- Press [MENU] to enter.
- Use ▲/▼ keys to select a scramble mode (MODE1-MODE3) to activate.
7.9 DTMF (Dual-Tone Multi-Frequency)
DTMF is an in-band signaling method used for automation systems and remote control, often to activate amateur radio repeaters.
DTMF Frequencies and Codes:
| 1209Hz | 1336Hz | 1477Hz | 1633Hz |
|---|
| 697Hz | 1 | 2 | 3 | A |
| 770Hz | 4 | 5 | 6 | B |
| 852Hz | 7 | 8 | 9 | C |
| 941Hz | * | 0 | # | D |
To send DTMF codes, press the corresponding key(s) while holding down the PTT key. This works even with keypad lock enabled.
7.10 Customization Options
- **Display Backlight (ABR - Menu 7):** Set backlight duration (ON/5sec/10sec/15sec/20sec).
- **Beep Prompt (BEEP - Menu 8):** Enable/disable key press tones.
- **Voice Function (VOICE - Menu 17):** Enable/disable voice prompts.
- **Language of the Menu (LANGUAGE - Menu 18):** Select English or Chinese.
- **Working Mode (MDF-A - Menu 24):** Choose between Frequency mode (FREQ), Channel mode (CH), or Channel name (NAME) display.
- **Roger Beep (ROGER - Menu 36):** Enable/disable end-of-transmission tone.
- **Power On Message (POWER ON MSG - Menu 40):** Customize welcome message (VOLTAGE, MESSAGE, LOGO, MODEL NAME).
- **Power On Password (POWER ON PWD - Menu 43):** Set a password required to turn on the radio.
- **Reset (Menu 42):** Reset VFO settings or ALL settings to default.
8. Programming Instructions
The BaoFeng UV-13 PRO can be programmed manually via the keypad or using programming software on a computer. For detailed manual programming steps, refer to section 7.3.
8.1 Programming with Software
To program your UV-13 PRO using a computer, you will need a 2-pin programming cable and the dedicated programming software (e.g., P15UV CPS).
- **Choose a 2-Pin Programming Cable:** Ensure you have the correct cable for your radio.
- **Connect the Cable:** Plug the 2-pin connector into the radio's accessory jack and the USB end into your computer.
- **Confirm Port:** Check your computer's Device Manager to confirm the USB cable port (e.g., COM4).
- **Disable Antivirus:** Temporarily turn off your computer's antivirus software to prevent interference with the programming software.
- **Download Software:** Obtain the official UV-13 PRO Programming Software.
- **Read from Radio:** Open the software and select "Read From Radio" to download the current settings.
- **Edit Frequencies:** Modify channel frequencies and other parameters as needed within the software.
- **Write to Radio:** Select "Write To Radio" to upload the new settings to your device.
Note: Always back up your radio's original settings before making changes. If you encounter issues with programming software (e.g., CHIRP or Abbree not working), ensure you are using the specific software designed for the UV-13 PRO model.
Video 1: How to Program the UV-13 PRO Walkie Talkie using a computer and programming software.
9. User Tips
- **Compatibility:** The UV-13 PRO can communicate with other Baofeng radios (e.g., UV-5R, BF-888S) as long as they are set to the same frequency.
- **Long-Range Communication:** Expect 3-10km in open areas (rural, suburbs, seaside) and 2-5km in cities/towns. Actual range depends on environmental obstructions.
- **Manual Programming:** Many settings, including frequencies, can be programmed directly from the radio's keypad without a computer. Refer to section 7.3 for detailed steps.
- **Software Issues:** If generic programming software like CHIRP or Abbree does not work, ensure you are using the specific programming software provided for the UV-13 PRO model.
- **Battery Life:** For optimal battery longevity, avoid overcharging and remove the radio from the charger within 6 hours of full charge.
- **Airband Reception:** The M version of the UV-13 PRO supports AM airband reception (108-136MHz). Check your specific model version if this feature is important to you.
10. Troubleshooting Guide
| Phenomena | Analysis | Solution |
|---|
| Cannot turn on the radio. | Battery improperly installed, battery power low, poor battery contact. | Reattach/recharge/replace battery, clean contacts. |
| Weak or intermittent voice during reception. | Battery voltage low, volume low, loose/incorrectly installed antenna, blocked speaker. | Recharge battery, increase volume, reattach antenna, clean speaker. |
| Cannot communicate with other group members. | Inconsistent frequency/signaling type, too far from others. | Verify TX/RX frequency/signaling, move closer. |
| Hear unknown voices or noise. | Interrupted by radios on same frequency, analog mode without signaling, too far from others, unfavorable position (e.g., blocked by buildings), external disturbance. | Change frequency/squelch level, request dealer to set signaling, move to open area, restart radio, avoid interference. |
| Radio keeps transmitting. | VOX turned on, headset not in place. | Turn off VOX, check headset. |
Note: If these solutions do not resolve your issues, please contact your dealer for technical support.
11. Technical Specifications
| Category | Specification |
|---|
| Brand Name | BAOFENG |
| Model Number | UV-13 PRO |
| Output Power (W) | 5W-10W |
| Maximum Range | 5km-10km (up to 16km in open areas) |
| Frequency Range | Multi Band: 136-174MHz (TX&RX), 220-260MHz (TX&RX), 400-520 MHz (TX&RX), FM65-108MHz (RX), AM108-136MHz (RX), Police350-390MHz (RX) |
| Storage Channel | 999 Groups |
| Battery Capacity (mAh) | High Capacity |
| Battery Included | Yes |
| Waterproof / Water-Resistant | IP45 |
| Dimensions | 13cm * 3cm * 5.5cm (Radio body: 26.9cm/10.6" H, 5.59cm/2.2" W, 3.56cm/1.4" D) |
| Material | Plastic |
| Is_Display | Yes |
| Walkie Talkie Type | Portable |
| Use | Others |
| Certification | CE, FCC |
| Channel Spacing | 25.0KHz (Wide) / 12.5KHz (Narrow) |
| Operation Voltage | DC 7.4 V ±10% |
| Transmission current | ≤1600mA |
| Receive Sensitivity | 0.25μV (12dB SINAD) |
| Rated Audio Power Output | 1W @ 16 ohms |
| Receive current | ≤380mA |
| Connection for accessories | 2 pin Kenwood jack |
| Antenna Impedance | 50 Ohm |
Note: All specifications are subject to change without prior notice or liability.

Figure 8: Product Dimensions and Specifications

Figure 9: EU Type Examination Certificate
12. Support and Disclaimer
12.1 Disclaimer
The Company strives for accuracy and completeness in this manual, but provides no warranty of accuracy or reliability. All specifications and designs are subject to change without notice due to continuous technological development. No part of this manual may be copied, modified, translated, or distributed without prior written consent. The Company does not guarantee the accuracy, validity, timeliness, legitimacy, or completeness of third-party products and contents involved in this manual.
12.2 Technical Support
If you encounter any issues not covered in this manual or require further assistance, please contact your dealer or the Superadio Store for technical support. An electronic version of this user manual (PDF) is available for download from the seller's product page.