Teverun Speed Limiter

Contents

Teverun Remote Control Speed Limiter User Manual

For Blade GT/GT+ II, Teverun Fighter Mini/10/11/11+ Electric Scooters (Manufactured Before 2024)

1. Introduction

This manual provides essential information for the safe and effective use of your Teverun Remote Control Speed Limiter. Please read all instructions carefully before installation and operation to ensure proper function and to prevent damage or injury. This speed limiter is designed to be compatible with specific Teverun and Blade electric scooter models manufactured before the year 2024.

The kit includes the speed limiter unit, a remote control, and an adapter cable (either XT60 or XT90, depending on your selection).

Teverun Speed Limiter Kit with remote control and XT60 connector

Image: Teverun Speed Limiter Kit, showing the main unit, remote control, and XT60 connector cable.

2. Safety & Warnings

Important Safety Information: Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture.
  • WARNING: Please mind potential fire risk and strictly follow the instruction manual for charging and storage.
  • While using the product, please wear protective equipment and fully comply with the applicable law and regulations.

3. Product Overview & Compatibility

The Teverun Remote Control Speed Limiter is designed to regulate the speed of compatible electric scooters. It comes in two main variants based on the battery connector type:

  • XT60 Speed Limiter: Suitable for Blade GT/GT+, Blade GT/GT+ II, Teverun Fighter 10/10+, and Teverun Fighter 11/11+ electric scooters.
  • XT90 Speed Limiter: Suitable for Teverun Fighter Supreme electric scooters.

Crucial Compatibility Note:

  • This speed limiter is ONLY compatible with Blade and Teverun scooters manufactured before 2024.
  • If your scooter is a 2024 version or newer, this speed limiter is NOT compatible as newer controllers may lack the necessary speed limit wires.
  • Your scooter's controller must have the appropriate XT60 or XT90 battery connector AND dedicated speed limiter wires for this product to function.
XT90 for 72V Teverun Fighter Supreme, XT60 for other models

Image: Visual guide for XT60 and XT90 connector types and their respective compatible scooter models.

Warning about 2024 scooter models not being compatible

Image: Important notice regarding incompatibility with 2024 version scooters due to controller changes.

4. Setup & Installation

Before beginning installation, ensure your scooter is powered off and the battery is disconnected for safety.

  1. Preparation: Remove all protective films from the speed limiter device and remote control.
  2. Verify Controller: Confirm that your scooter's controller has the correct XT60 or XT90 battery connector and the dedicated speed limiter wires.
  3. Connect Power: Connect the speed limiter unit's XT-type cable between your scooter's battery and the controller. Ensure the connectors are securely fastened.
  4. Connect Speed Limiter Wires: Connect the small two-pin connector from the speed limiter unit to the corresponding speed limiter wire on your scooter's controller.
XT60 Speed Limiter installation diagram showing battery and speed limiter wire connections

Image: Installation diagram for XT60 version, highlighting the battery connector and speed limiter wire connections on the controller.

XT90 Speed Limiter installation diagram showing power and speed limit wires

Image: Installation diagram for XT90 version, highlighting the power connector and speed limit wires on the controller.

Remote Control Charging

The remote control requires charging. Connect the provided USB cable to the remote control and a certified 5V power adapter (not included).

5. Operating Instructions

  1. Power On: Press and hold the 'ON' button on the remote control for 3 seconds to turn on the speed limiter device.
  2. Change Modes: Short press the 'ON' button to cycle through different speed modes (if applicable).
  3. Power Off: Press and hold the 'OFF' button on the remote control for 3 seconds to turn off the speed limiter device.

6. Maintenance

  • After use, turn off the speed limiter device using the remote control.
  • Store the device in a dry place, away from direct sunlight and extreme temperatures.
  • Keep the device and its components clean and free from dust and debris.
  • Regularly inspect all cables and connectors for any signs of wear or damage. Do not use if damaged.

7. Troubleshooting

If you encounter issues with your speed limiter, consider the following:

  • Device not powering on: Ensure the remote control is charged. Check all cable connections for security.
  • Speed limiter not functioning: Verify that your scooter model and manufacturing year are compatible (before 2024). Confirm your controller has the correct XT connector type and speed limiter wires.
  • Intermittent operation: Check for loose connections or damaged wiring. Ensure the device is not exposed to moisture.

If problems persist, please contact customer support for assistance.

8. Specifications

Feature Detail
Product Name Electric Scooter Parts
Model Number KB-PS1442355509
Type Remote Control Speed Limiter
Connector Types XT60, XT90 (variant dependent)
Compatibility Blade GT/GT+ II, Teverun Fighter Mini/10/11/11+ (pre-2024 models)
Origin Mainland China
Package Dimensions (approx.) Length: 10 cm, Width: 10 cm, Height: 5 cm
Package Weight (approx.) 0.3 kg

9. User Tips

  • Always verify your scooter's exact model and manufacturing year to ensure compatibility, especially the 'before 2024' requirement.
  • Before purchasing, check your scooter's controller for the correct battery connector type (XT60 or XT90) and confirm the presence of dedicated speed limiter wires.
  • If you are unsure about compatibility or installation, it is recommended to seek professional assistance or contact the seller for technical support.
  • Avoid any unauthorized modifications to your scooter or the speed limiter, as this may void warranties and pose safety risks.

10. Warranty & Support

LOOMO Wheel Store guarantees that all goods sold are original and have undergone rigorous quality checks to ensure good quality upon receipt. We also sell all accessories for the products we offer.

If you encounter any quality problems with your product, please contact us as soon as possible for a resolution. Old customers may enjoy preferential prices on future accessory purchases.

All items are professionally packed with great care to ensure safe delivery.

For technical support or any queries regarding the product, please contact the seller directly.

11. Compliance Information

Product name: Electric Scooter Parts

Model: KB-PS1442355509

Manufacturer: Ningbo Kaabo Technology Co., Ltd. (Address: 238 Yunlin Middle Road, Haishu District, Ningbo, Zhejiang, China)

Date of Manufacture: June 2024

E-mail: support_e_wheel@163.com

EU Authorized Representative: Bright star consulting e.K. (Humboldtstr.5, 31812 Bad Pyrmont, Germany; Phone: +49 2385772667; Email: utaundnico@hotmail.com)

MADE IN CHINA

Compliance Markings:

Compliance markings including CE, UKCA, FC, RoHS

Image: Compliance markings (CE, UKCA, FC, RoHS) indicating adherence to relevant standards.

A detailed user manual in PDF format is also available for download: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.