ANDELI MCT-416

Contents

ANDELI MCT-416 4-in-1 Multifunctional Welder Instruction Manual

Model: MCT-416

Introduction

Thank you for choosing the ANDELI MCT-416 4-in-1 Multifunctional Welder. This machine is designed for versatility, offering MIG, TIG, MMA (Stick), and Plasma Cutting capabilities in a single compact unit. This manual provides essential information for safe and effective operation, maintenance, and troubleshooting. Please read it thoroughly before using the equipment.

ANDELI MCT-416 4-in-1 Multifunctional Welder front view

Front view of the ANDELI MCT-416 4-in-1 Multifunctional Welder.

Safety Information

Always prioritize safety when operating welding and cutting equipment. Failure to follow safety guidelines can result in serious injury or death.

  • Eye and Face Protection: Always wear a welding helmet with appropriate shade lenses to protect your eyes and face from arc rays and sparks.
  • Body Protection: Wear flame-resistant clothing, heavy-duty gloves, and safety shoes. Avoid synthetic fabrics.
  • Ventilation: Ensure adequate ventilation to remove welding fumes and gases from your work area.
  • Fire Prevention: Keep a fire extinguisher nearby. Remove all flammable materials from the work area.
  • Electrical Safety: Ensure the machine is properly grounded. Do not operate in wet conditions. Inspect cables and connections for damage before each use.
  • Hot Surfaces: Welding equipment and workpieces become extremely hot. Allow them to cool before handling.
  • Gas Cylinders: Secure gas cylinders properly to prevent them from falling. Handle with care.
  • Children and Bystanders: Keep children and unauthorized personnel away from the welding area.

Package Contents

The following items are typically included with your ANDELI MCT-416 welder:

  • ANDELI MCT-416 4-in-1 Welder Unit
  • Ground Clamp
  • MIG Torch (3M)
  • Gas Pipe (3M)
  • Nozzle (20 pieces)
  • Nozzle Shield (2 pieces)
  • Flux-cored Wire
  • Teflon Tape
  • TIG Torch (4M)
  • Collet (10 pieces)
  • Nozzle (10 pieces)
  • Tungsten Electrode (10 pieces)
ANDELI MCT-416 with included accessories

The ANDELI MCT-416 welder and its standard accessories.

Product Overview

The MCT-416 is a versatile welding and cutting machine featuring an intuitive LED display and robust construction.

Key Features:

  • 4-in-1 Functionality: MIG, TIG, MMA, and Plasma Cutting.
  • LED Display: Large digital screen for easy adjustment of welding parameters.
  • Synergic Control: Stepless adjustment knob for simplified parameter setting in MIG mode.
  • Non-HF Plasma Cutting: Capable of clean cutting up to 20mm and limit cutting up to 25mm.
  • Portable Design: Compact dimensions (490x225x340mm) and lightweight (12.8KG) for easy transport.
ANDELI MCT-416 dimensions and weight

Dimensions and weight of the ANDELI MCT-416 welder.

Applications:

This welder is suitable for a wide range of applications, including:

  • Welding Angle Iron, Square Tube, Stainless Steel
  • Fabrication of Steel Sheds, Steel Plates, Railings
  • Repair and construction of Iron Doors, Metal Baskets, Metal Shelves
ANDELI MCT-416 application examples

Examples of materials and structures that can be worked on with the MCT-416.

Setup

Proper connection of welding torches and accessories is crucial for safe and effective operation. Refer to the diagrams below for correct setup for each welding/cutting process.

Welding Torch Connection:

Welding Torch Connection diagrams for MIG/MAG, Flux MIG, LIFT TIG, CUT, MMA

Diagrams illustrating the correct connection of torches for MIG/MAG, Flux MIG, LIFT TIG, CUT, and MMA processes.

General Setup Steps:

  1. Ensure the machine is turned off and unplugged from the power source.
  2. Connect the ground clamp securely to the workpiece or welding table.
  3. Attach the appropriate torch (MIG, TIG, or Plasma) to the corresponding connectors on the front panel.
  4. For MIG (Gas) and TIG welding, connect the gas hose from the machine to your shielding gas cylinder (e.g., CO2, Argon).
  5. For MIG welding, install the correct size welding wire spool inside the machine and feed the wire through the torch liner.
  6. For MMA welding, insert the electrode into the electrode holder.
  7. For Plasma Cutting, ensure the air compressor is connected and supplying adequate air pressure.
  8. Plug the machine into a suitable power outlet (220V).
  9. Turn on the machine and select the desired welding/cutting mode.

Operating Modes

The MCT-416 offers four primary operating modes, each with specific applications and parameter adjustments.

LED Display and Controls:

LED screen details for MIG, LIFT TIG, CUT, MMA

The LED screen provides clear readouts and allows for easy parameter adjustments.

Simple Panel details for MIG, TIG, CUT, MMA

Detailed view of the control panel functions for each mode.

1. MIG Welding (Gas/Gasless)

MIG (Metal Inert Gas) welding is ideal for fast and efficient welding of various metals. The MCT-416 supports both gas-shielded and gasless (flux-cored) MIG welding.

  • Gas Modes: CO2, MIX, Flux.
  • Recommended Welding Thickness: 1-8 mm.
  • Controls: Use the stepless adjustment knob for synergic control of voltage and wire feed speed. Features include Gas Check and Wire Check.
MIG welding with wire spool and gas modes

MIG welding setup showing wire spool and gas mode selection.

Video demonstrating the various welding and cutting processes of the MCT-416, including MIG, TIG, MMA, and Plasma Cut.

2. LIFT TIG Welding

LIFT TIG (Tungsten Inert Gas) welding provides precise control and high-quality welds, especially for thinner materials.

  • Type: Non-high frequency TIG welding.
  • Suitable for Welding: 1-8mm thickness.
  • Process: Lift arc ignition for minimal tungsten contamination.
LIFT TIG welding in progress

LIFT TIG welding process for high-quality, precise welds.

3. MMA Welding (Stick)

MMA (Manual Metal Arc) welding, also known as Stick welding, is versatile for outdoor use and on dirty or rusty materials.

  • Electrode Compatibility: Capable of welding with 1.6mm, 2.0mm, and 3.2mm welding rods.
MMA welding in progress

MMA welding in action, suitable for various electrode sizes.

4. Plasma Cutting (CUT)

Plasma cutting uses an accelerated jet of hot plasma to cut through electrically conductive materials.

  • Type: Non-high frequency plasma cutting.
  • Cutting Capacity: Up to 20mm for clean cutting, 25mm for limit cutting.
  • Pilot Arc Start: Improves cutting performance.
Plasma cutting in progress

Plasma cutting process for efficient material separation.

Specifications

Detailed technical specifications for the ANDELI MCT-416 welder:

FunctionMIGTIGMMACUT
Power Supply Voltage220V
Frequency50/60Hz
Power Factor0.73
Efficiency77%
No-Load Voltage (V)53290
Rated Input Power (KW)5.74.276.2
Rated Input Current (A)26193228
Welding Current Range (A)50-16010-16010-16020-40
Duty Cycle (40% 10min)20% (160A), 60% (92A), 100% (72A) for MIG/TIG/MMA; 20% (40A), 60% (33A), 100% (18A) for CUT
Per Flow Time (S)1-100-1.0
Post-Flow Time (S)-0-5.0-0-5.0
Protection ClassIP21S
Insulation ClassH
CoolingAir Cooling
Dimensions (MM)490*225*340mm
Net Weight (KG)12.8KG

Technical specifications for the ANDELI MCT-416.

Maintenance

Regular maintenance ensures the longevity and optimal performance of your welding machine.

  • Cleaning: Regularly clean the machine's exterior and ventilation openings to prevent dust and debris buildup. Use compressed air to clear internal components if necessary, ensuring the machine is unplugged.
  • Cable Inspection: Periodically inspect all cables, hoses, and connections for wear, cuts, or damage. Replace any damaged components immediately.
  • Torch Maintenance: Clean MIG gun nozzles, contact tips, and diffusers. For TIG, ensure the tungsten electrode is sharp and free of contamination. For plasma, check electrodes and nozzles for wear.
  • Wire Feeder: Clean the wire feeder rollers and ensure they are properly aligned and tensioned for smooth wire feeding.
  • Storage: Store the machine in a clean, dry environment when not in use.

Troubleshooting

This section provides general guidance for common issues. For complex problems, contact customer support.

  • No Power: Check power cord connection, circuit breaker, and ensure the power switch is on.
  • No Arc: Verify ground clamp connection, electrode/wire contact, and correct current settings. For TIG, check tungsten sharpness and gas flow. For plasma, check air pressure.
  • Poor Weld Quality: Adjust current/voltage, wire feed speed (MIG), gas flow, or travel speed. Ensure material is clean.
  • Wire Feeding Issues (MIG): Check wire spool installation, tension on feeder rollers, and ensure the contact tip and liner are not clogged or worn.
  • Overheating: Allow the machine to cool down. Ensure ventilation openings are clear and the duty cycle is not exceeded.

User Tips

  • Practice on Scrap: Before working on important projects, practice on scrap pieces of the same material and thickness to fine-tune your settings and technique.
  • Cleanliness is Key: Always ensure your workpiece is clean and free of rust, paint, or oil for the best welding and cutting results.
  • Proper PPE: Never compromise on personal protective equipment. Your safety is paramount.
  • Gas Management: For gas-shielded processes, monitor your gas levels to avoid running out mid-weld, which can lead to porous welds.

Warranty and Support

For warranty information, technical support, or service inquiries, please contact the ANDELI customer service department or your authorized dealer. Keep your purchase receipt and product serial number handy for faster service.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.